1. DL manuals
  2. BIRO
  3. Grinder
  4. EMG-32
  5. Operating Manual And Parts List

BIRO EMG-32 Operating Manual And Parts List

Summary of EMG-32

  • Page 1

    Model emg-32 ergonomic mixer-grinder/chopper operating manual and parts list item no. Emg92099 manual form no. Emg32man-11-03-6 comm important notice this manual contains important safety instructions which must be strictly followed when using this equipment. Item no. Emg92099 manual form no. Em...

  • Page 2: Table of Contents

    Table of contents page notice to owner and operators ..................................................................................1 safety tips ....................................................................................................................................2 installation .......

  • Page 3

    Biro’s products are designed to process food products safely and efficiently. Unless the oper- ator is properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner to assure that this machine is used properly and safely, strictly follo...

  • Page 4: Safety Tips

    Safety tips rotating grinding auger & rotating mixing paddles to avoid serious personal injury never touch this machine without training and authorization by your supervisor. never place hands into machine input or output openings. never open machine during operation. only use a qualified el...

  • Page 5: Installation

    Installation to avoid serious personal injury, properly install equipment in adequate work area always use qualified technician and electrician for installation. always connect to proper voltage & phase. always install equipment in work area with adequate light and space away from children and...

  • Page 6

    Motor wiring and electrical requirements 1. Interchange of current is made in motor outlet box. Leads are properly marked. Changing instructions are on the motor plate or motor outlet box. 2. All mixer-grinder/choppers are wired 208 volts unless otherwise specified. Be sure motor specifications (vol...

  • Page 7: Operation

    10. Two sets of green and red pushbuttons are located at the front of the machine that activate the magnetic contactors that control the mix and grind motors. The time delay product mixer safety cover interlock switch is mounted in the motor compartment. The product mixer safety cover cannot be open...

  • Page 8: Operation (Cont.)

    Operation (cont.) never open machine during operation. do not wear gloves while operating. do not tamper with, bypass, alter, or modify this equipment in any way from its original condition. never operate machine with product mixer safety cover opened or removed or magnetic interlock switch ...

  • Page 9: Maintenance

    Maintenance rotating grinding auger to avoid serious personal injury always turn off, unplug from power source and perform lockout/tagout procedure to this machine before servicing. never touch this machine without training and authorization by your supervisor. never place hands into machine i...

  • Page 10

    B. Lubrication (cont.) recommended types of chain lubricant are those with molybdenum disulphide or graphite added. Also bonded lubricants such as dow corning molykote 321r or equivalent are excellent for open chains. The lubricant should be of a viscosity whereby it will “flow” somewhat and penetra...

  • Page 11

    9.

  • Page 12

    Lubrication for grove gear reducer 1. Factory filling the speed reducers are oil filled at the factory to the proper level for the standard mounting position. The oil level should be checked and adjusted (if necessary) prior to operation, using the oil level plug provided and while the unit is orien...

  • Page 13: Lubrication and Maintenance

    Emg20301g-r grove gear reducer lubrication and maintenance after serial no. 6987 view is from opposite end of drum lubricants for emg20301g-r grove gear worm reducer the precision-made gears and bearings in grove gear speed reducers require high-grade lubricants of the proper viscosity to maintain t...

  • Page 14

    #53953, mixer drive shaft seal replacement 1. Clean the inside of the groove of the mixer drive shaft seal and mating contact surface of the tub wall throughly with scotch-bright or a roughing pad. 2. Dispense a small amount of #454 loctite adhesive to both these areas - assure even coverage. 3. Wip...

  • Page 15: Cleaning

    Cleaning to avoid serious personal injury always turn off, unplug machine from power source and perform lockout/tagout procedure to this machine before cleaning or servicing. only use recommended cleaning equipment, materials, and procedures. never spray water or other liquid substances direct...

  • Page 16: Mixing Paddle Installation

    Mixing paddle installation s/n’s 6001 to 6057 10 the mixing paddles are not inter- changeable, however they are timed to allow for proper mix action. Paddle installation: install the corresponding mixer paddles by matching the male and female hub drives with the respective female and male paddle hub...

  • Page 17: Mixing Paddle History

    Mixing paddle history by serial number 11 15.

  • Page 18: Electric Foot Switch

    Electric foot switch 12 footswitch parts list 224-2 cord connector, wt, straight, 3 4 " 52654 male plug w/6’ cord, 5 wire 56292 female receptacle 90° 52661 male plug w/12’ cord, 5 wire 52668 footswitch w/12’ cord and plug 53693 footswitch 53693-a cover guard 53693-c cover gasket 53693-d cover screw ...

  • Page 19: Electrical Schematic

    Electrical schematic 13 17.

  • Page 20

    14 electrical schematic emg-32 with serial no. 6075-6300 with electrical foot switch option three phase 18.

  • Page 21

    15 19.

  • Page 22: Electrical Schematic

    Electrical schematic 16 starting with serial no. 6301 – on with pneumatic foot switch option three phase 20

  • Page 23

    17 electrical schematic emg-32 with serial no. 6075-6300 with pneumatic foot switch option three phase 21.

  • Page 24

    22 part no. Description 226ee-0l01.9g overload, b18k-g, 1.3-1.9 amp, 440-460 volt 226ee-0l4i overload, b18k-i, 2.5-4 amp, 208-240 volt 56300r air switch – dpdt momentary 56301e air switch mounting bracket blk323 end barrier emg90177a contactor 24v coil w/aux.Contacts emg90180 aux. Contact block – n....

  • Page 25: Items Not Shown

    19 items not shown 14672 multi hole strain relief 1773-1 lock ring, ½” 241-b boot, hubbell 2567 ring terminal, red 418 wire nut, orange 419 wire nut, yellow 420 wire nut, red 53511 cord connector, 14/4 al 53687 decal “caution do not fill above line” 53689 cord connector, 10/4 al 53891 auger drive sh...

  • Page 26

    24.

  • Page 27

    25.

  • Page 28

    26.

  • Page 29

    23 journal box assembly p/n – 53886 item no. Description 53609 journal box, #62001 on 53724 auger drive shaft, #62001 on 53785 journal box seal (2 ea.) 53886 journal box assembly complete 53888, 53940 front bearing cup/cone assembly, order h310a item no. Description 53889, 53939 rear bearing cup/con...

  • Page 30: Optional Equipment

    Optional equipment 24 28.

  • Page 31: Safety Label Locations

    Safety label locations caution keep hands out of hopper 25 29.

  • Page 32: Tande

    30 tande m op er at ion il lust r at ion.

  • Page 33: Warning

    31 operator’s signature page warning read and understand this entire manual before signing below my signature attests that i have completely read and understand this manual. I realize that this machine, if operated carelessly, can cause serious injury to myself and others. Name (print) signature dat...

  • Page 34

    28 limited warranty: warranty: the biro manufacturing company warrants that the biro emg-32 mixer grinder/chopper will be free from defects in material and workmanship under normal use and with recommended service. Biro will replace defective parts, which are covered by this limited war- ranty, prov...