1. DL manuals
  2. Bissell
  3. Vacuum Cleaner
  4. 1698
  5. Repair Manual

Bissell 1698 Repair Manual

Other manuals for 1698: Service Manual
Manual is about: Service Center Repair Guide

Summary of 1698

  • Page 1

    Powersteamer® proheat pro-tech™ #1698’s, #1699’s, & #7920’s service center repair guide.

  • Page 2: Table of Contents

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 1 table of contents how to use this repair guide page 2 ul recommended high voltage test page 2 using the servicing platform page 3 preliminary diagnostic checks page 3 functional systems...

  • Page 3: How to Use This Repair Guide

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 2 how to use this repair guide the instructions in this repair guide pertain to the bissell powersteamer proheat (#1698) and the bissell proheat clearview(#1699). The information identifi...

  • Page 4: Using The Servicing Platform

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 3 using the servicing platform begin by placing the unit on the servicing platform. Servicing platform should fit securely under the unit and raise its wheels off the servicing surface. P...

  • Page 5

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 4 3. Check seals on clear water tank and solution tank. If necessary, re-seat or replace seals. 4. Check valve action on clear water tank and solution tank by depressing them with your fi...

  • Page 6: Functional Systems Check

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 5 8. Manually rotate motor shaft to determine that motor, brush and pump are moving smoothly and quietly. 9. Remove any debris which may be hindering the free movement of these components...

  • Page 7: Taking The Unit Apart

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 6 taking the unit apart 1. Unplug the unit. 2. Recline the handle backwards fully. 3. Turn smartmix to "normal" traffic setting. 4. Remove the solution and clean water tanks. 5. Remove cl...

  • Page 8

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 7 10. Check lines for evidence of pinching and restricted flow. Straighten and un-pinch lines as necessary. ( see base photo page 18) 11. After removing housing, check that the smartmix p...

  • Page 9: Lower Handle Issues

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 8 lower handle issues 1. Handles must be reassembled to ensure that hoses are not pinched. 2. Clear any blockages in the heater inlet and outlet lines with a finishing nail or similar obj...

  • Page 10: Motor Replacement Procedure

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 9 2. Make certain the background window has its tabs placed properly. 3. Make certain the gasket is in place on top of the background window. Motor replacement procedure 1. Remove main ho...

  • Page 11

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 10 5. Remove the four screws on the motor cover. 6. Rock the motor duct out of position. 7. Lift out the motor. 8. Disconnect all wires. 9. Remove, clean and save the two gaskets on the m...

  • Page 12

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 11 13. Attach the "hot" and "neutral" terminals onto the new motor. 14. Turn the motor so that the "ground" terminal is oriented downward. 15. Loop the wires around the bottom of the moto...

  • Page 13

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 12 20. Replace the spray tips. 21. Replace the flow indicator by pulling the two tubes downward and making sure the flow indicator is seated snugly. 22. Replace all tubing and wiring in i...

  • Page 14

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 13 putting the unit back together 1. Follow the assembly diagram to ensure that all parts are replaced properly. 2. Make sure the foot pedal is in the proper position. 3. The smartmix sho...

  • Page 15

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 14 7. Clean any debris from the flow indicator. Insert with post up, then lightly tighten flow indicator cap. 8. Make sure the rope gasket for the window is in place on the housing. Also,...

  • Page 16: Pump Replacement

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 15 pump replacement 1. Unplug the unit. 2. Remove the two solution tanks. 3. Remove spray tips from guides. 4. Remove the brush and cog belt by removing the screw from the orange retainin...

  • Page 17

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 16 8. Place stretch belt on new pump. 9. Re-seat new pump into position and screw into place (4 screws). 10. Reattach tubing 11. Reattach brush, cogbelt, and retainer arm. 12. Screw orang...

  • Page 18

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 17 wiring diagram.

  • Page 19

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 18 overhead view of base.

  • Page 20

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 19 lower handle disassembly 1. Remove the two screws located near the bottom of the tool caddy on the back of the machine. 2. Remove the two bolts and nuts that go through the upper part ...

  • Page 21

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 20 circuit board replacement 1. Disassemble lower handle assembly according to instructions on page nineteen. 2. Remove the black circuit board wire from the power switch (this is the bla...

  • Page 22

    B issell powersteamer® proheat™ series service center repair guide printed february, 2001 1/30/2004 (revision 1) 21 speed sensor replacement 1. Remove the main housing according to instructions on page six. 2. Remove the right side wheel (held in place by an e-clip on the end of the axle). 3. Gently...