Bissell 28F4 SERIES User Manual - Roubleshooting

Page of 16

Download

Print this page

Bookmark us

w w w. b i s s e l l . c o m

roubleshooting

WARNING:

To reduce the risk of electric

shock, turn power OFF and dis-

connect plug from electrical

outlet before performing

maintenance or troubleshooting.

Vacuum cleaner won't pick up dirt

Possible causes

1. Incorrect height adjustment

2. Hose not attached to suction opening

3. Twist 'n Snap hose not securely attached

4. Crack or hole in hose

5. Broken or worn drive belt

6. Rotating floor brush bristles worn

7. Rotating floor brush jammed

8. Clog in vacuum

9. Dirt container full

10. Dirt container not installed properly

11. Filters are dirty

12. Primary separator missing or installed incorrectly

13. TurboBrush™ Tool is clogged or debris is

wrapped around the brush

Remedies

1. Adjust powerfoot to correct height setting

2. Grasp Quick Release handle and firmly push

hose wand onto the suction opening.

3. Make sure Twist 'n Snap hose is snapped

into locked position

4. Check hose and replace if needed

5. Replace drive belt, see page 11

6. Replace brush

7. Remove brush and clean debris from brush ends

8. Follow instructions for clearing clogs on page 12

9. Empty dirt container

10. Position correctly and lock in place

11. Check and clean inner and outer circular filters and,

pre-motor filter, replace post-motor filter

12. Check for a clog in the tube in the center of the dirt

container, clear and properly install primary separator

13. Maintain TurboBrush™ Tool, see page 10

Tools won't pick up dirt

Possible causes

1. Crack or hole in hose

2. Vacuum hose, wand or tools clogged

3. Dirt container full

4. Dirt container or upper tank not installed properly

5. Filters are dirty

6. Primary separator missing or installed incorrectly

Remedies

1. Check hose and replace if needed

2. Follow instructions for clearing clogs on page 12

3. Empty dirt container

4. Position correctly and lock in place

5. Check and clean inner and outer circular filters and,

pre-motor filter, replace post-motor filter

6. Check for a clog in the tube in the center of the dirt

container, clear and properly install primary separator

Vacuum cleaner won’t turn

Possible causes

1. Power cord not firmly plugged in

Remedies

1. Check electrical plug

Vacuum cleaner difficult to push

Possible causes

1. Incorrect height adjustment

Remedies

1. Adjust powerfoot to correct height setting

Visible dirt escaping from cleaner

Possible causes

1. Dirt container full

2. Filters missing or installed incorrectly

Remedies

1. Empty dirt container

2. Check inner and outer circular filter and post-motor

filter for correct installation

« ‹ Prev 10 11 12 13 14 15 16 Next › »

Summary of 28F4 SERIES

Page 1
2 thank you user's guide 28f4, 59q4 series 220-240v safety instructions product view assembly operations maintenance and care troubleshooting replacement parts 3 4 5 6-7 8-12 13-14 14 warranty consumer services 15 16 bagless turbo.
Page 2
W w w. B i s s e l l . C o m t hanks for buying a bissell powerforce™ pet cyclonic vacuum we’re glad you purchased a bissell powerforce pet cyclonic vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your bissell powerf...
Page 3: Mportant Safety Instructions
T hanks for buying a bissell powerforce™ pet cyclonic vacuum w w w. B i s s e l l . C o m i mportant safety instructions 3 when using an electrical appliance, basic precautions should be observed, including the following: read all instructions before using your upright vacuum. Warning: to reduce the...
Page 4: Roduct View
W w w. B i s s e l l . C o m 4 p roduct view caution: do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures. Handle turbobrush ™ tool powerfoot furniture protection guard height adjustment knob carrying handle power switch crevice tool quick reach ™...
Page 5: Ssembly
W w w. B i s s e l l . C o m a ssembly the only tool you’ll need to assemble your vacuum cleaner is a screwdriver. Attach handle to vacuum 1. Locate the vacuum handle and remove the screw packet taped to the base of the handle. 2. Stand the vacuum upright and place the handle on the top of the vacuu...
Page 6: Perations
W w w. B i s s e l l . C o m o perations 6 handle position press the handle release pedal with your foot to place your bissell powerforce pet into one of three cleaning positions. 1. Upright- for storage and above floor cleaning with special tools. 2. Normal cleaning- press handle release pedal once...
Page 7: Perations
W w w. B i s s e l l . C o m 7 o perations special tools your bissell powerforce pet is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools. 1. Raise handle to upright position. 2. Grasp the quick reach handle a...
Page 8: Aintenance and Care
W w w. B i s s e l l . C o m m aintenance and care 8 to maintain maximum cleaning performance from your bissell powerforce pet cyclonic, perform these simple maintenance steps. 1. Empty the dirt container when the dirt reaches the “full” line on the side. 2. Check the inner and outer circular filter...
Page 9: Aintenance and Care
W w w. B i s s e l l . C o m 9 m aintenance and care 1. Unplug cleaner from electrical outlet. 2. Remove the dirt container as described in the previous section. Grasp the filter cup located at the bottom of the dirt container and twist counterclockwise to unlock and remove. 3. Grasp the circular fi...
Page 10: Aintenance and Care
W w w. B i s s e l l . C o m m aintenance and care 10 the post-motor filter is a hepa media filter*, which assists in the filtration process to return clean air to the room. 1. Unplug the vacuum from electrical outlet. 2. Remove the filter door, located on the front of the vacuum. 3. Remove the post...
Page 11: Aintenance and Care
W w w. B i s s e l l . C o m 11 m aintenance and care you should check your vacuum cleaner’s rotating floor brush and drive belt regu- larly for wear or damage. You should also clean the brush and brush ends of string, hair and carpet fibers. These can wrap around the brush and hamper its ability to...
Page 12: Aintenance and Care
W w w. B i s s e l l . C o m m aintenance and care 12 replace light bulb 1. Unplug cleaner from electrical outlet. 2. Using a flat screwdriver, table knife or coin, insert into the slot on the right of the lens and gently push inner latch to the left, as shown, to remove the lens. 3. Remove the bulb...
Page 13: Roubleshooting
W w w. B i s s e l l . C o m 13 t roubleshooting warning: to reduce the risk of electric shock, turn power off and dis- connect plug from electrical outlet before performing maintenance or troubleshooting. Vacuum cleaner won't pick up dirt possible causes 1. Incorrect height adjustment 2. Hose not a...
Page 14: Roubleshooting
Item part no. Part name 1 32074 style 7/9/10/12/14 drive belt (2-pack) 2 203-1297 standard headlight bulb 3 203-1056 crevice tool 4 203-1059 combination dusting brush/upholstery tool 5 203-1068 extension wand 6 203-1216 wire reinforced twist ‘n snap vacuum hose) 7 203-5624 wide brush roll 8 32064 st...
Page 15: Arranty - Bissell Powerforce
W w w. B i s s e l l . C o m 15 w arranty - bissell powerforce ™ pet this warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, ple...
Page 16: Consumer Services
©2012 bissell homecare, inc grand rapids, michigan all rights reserved. Printed in china part number 110-4497 rev 11/11 visit our website at: www.Bissell.Com b issell consumer services w w w. B i s s e l l . C o m 16 if your bissell product should require service: call bissell consumer services at t...