- DL manuals
- Bull
- Griddle
- 97008
- Assembly & Operating Instructions
Bull 97008 Assembly & Operating Instructions
Summary of 97008
Page 1
Assembly & operating instructions model #97008 griddle, built-in, l.P. (propane) model #97009 griddle, built-in, n.G. (natural gas).
Page 2: Table Of Contents
Table of contents page # safety instructions ……………………...…………………………………………………….………………………..………………………...2 the location for your griddle.. ……..…………………………………………………………….....……….…………………........2 checking for gas leaks ………………………………………………………………………………………...…..……………………..2 natural gas safety …………………………………….……………...
Page 3: Safety Instructions
Safety instructions this gas griddle must be installed in accordance with local codes or, if in an area without local codes, with the latest edition of the national fuel gas code ansi z223.1. In canada, installation must conform to the standard can/ cga 1-b149.1 and/or .2 (installation code for gas ...
Page 4: Safety Instructions
Safety instructions (cont.) natural gas safety your natural gas griddle is designed to operate on natural gas only, at a pressure of 4” water column (w.C.) regulated at the natural gas regulator attached at the back of the griddle. Check with your gas utility for local gas pressure and with your loc...
Page 5: Safety Instructions
Safety instructions (cont.) propane gas safety your propane gas griddle is designed to operate on propane gas only, at a pressure regulated at 11” water column (w.C.) when equipped with the correct propane orifices on the valves and a propane regulator on the supply line regulated at the residential...
Page 6: Installation Instructions
Please read these instructions before installing your gas griddle installation instructions your built-in gas griddle comes to you fully assembled. We strongly recommend professional installation and hookup of the gas griddle. These instructions will provide you with the measurements necessary for y...
Page 7: Installation Instructions
Installation instructions (cont.) connecting to gas source refer to the following instructions and illustrations for typical gas supply connections. We strongly suggest professional installation and hook-up of the gas griddle. Important: before connecting griddle to gas source, make sure griddle con...
Page 8: Installation Instructions
Installation instructions (cont.) outdoor natural gas griddle installation specifications note: - vents must be provided for combustion air and ventilation on both sides of built-in cabinet. - when choosing a location for your gas griddle keep in mind that it should never be located under any overhe...
Page 9: Installation Instructions
Installation instructions (cont.) outdoor propane gas griddle installation specifications note: - vents must be provided for combustion air and ventilation on both sides of built-in cabinet. - when choosing a location for your gas griddle keep in mind that it should never be located under any overhe...
Page 10: Installation Instructions
Installation instructions (cont.) lp gas tank retention if using a lp gas tank, the tank must be properly secured within the structure to prevent being knocked over. The tank retention system must be securely fastened to the bottom of the island with the use of bolts, washers and nuts. There must be...
Page 11: Inspecting
Inspecting i cleaning burners and gas valve orifices by following these cleaning procedures on a timely basis, your griddle will be kept clean and working properly with minimum effort. Caution – always turn off the gas supply prior to clearing your griddle. Burner cleaning 1. Remove burners from the...
Page 12: Inspecting
Inspecting i cleaning burners and gas valve orifices (cont.) 4. Remove the rear lid screws. 5. Remove the bottom griddle insert screws. 6. Carefully remove the griddle insert to expose the burners. 11.
Page 13: Inspecting
Inspecting i cleaning burners and gas valve orifices (cont.) 7. Remove the cotter pin from each burner before attempting to lift up the burners. 8. Use a narrow bottlebrush with a flexible handle. Run the hook through each burner tube and burner several times. 9. Wire brush entire outside surface of...
Page 14: Valve Orifices
Inspecting / cleaning burners and gas valve orifices (cont.) burner replacement into insert caution – always turn off the gas supply prior to clearing your griddle. 1. Replace burners back into the insert assembly. There is no need to replace the cotter pin back into the cast peg, it is for shipping...
Page 15: Valve Orifices
Inspecting / cleaning burners and gas valve orifices (cont.) 2. Light any burner by pushing its control knob in fully and slowly (3 to 4 seconds) turning it about 1/4 turn to the left (counter-clockwise) until a click is heard. The 3 to 4 second duration should provide enough gas to light the burner...
Page 16: Valve Orifices
Inspecting / cleaning burners and gas valve orifices (cont.) flex line and regulator placement due to packaging purpose, the regulator will be assembled horizontally in the carton. It is imperative that the regulator carefully be turned pointing downward before use. Now your gas griddle is ready to ...
Page 17: Lighting Procedures
Lighting & operating instructions lighting procedures lighting burner(s): 1. Become familiar with the safety guidelines at the front of the manual. Do not smoke while lighting griddle or checking gas supply connections! 2. If your griddle fuel source is a lp gas cylinder, check to see that cylinder ...
Page 18: Cleaning & Maintenance
Cleaning & maintenance cleaning the griddle insert if grease is allowed to accumulate on the griddle surface, it will carbonize and become difficult to remove. In order to avoid this, regular maintenance and cleaning is required. To clean griddle surface, follow these steps: 1. Remove excess oil, gr...
Page 19: Troubleshooting
Troubleshooting if griddle fails to operate properly 1. Turn off gas at source, turn control knobs to “off”, and wait five minutes before trying again. 2. Check gas supply/connections. 3. Repeat lighting procedure. If griddle still fails to operate properly, turn “off” gas at source, turn control kn...
Page 20: Troubleshooting
Troubleshooting (cont.) yellow flame once the entire burner is operating, check the flame color to be sure it is mostly blue (some yellow color will be present because of impurities in the fuel). If the flame is golden or yellow in color the reason could be oil film or other foreign matter on burner...
Page 21: Locations Of Serial Number
Locations of serial number essential information about your product is encoded in the serial number of your griddle. This information will be required for all warranty claims, ordering replacement parts and will identify any variations of your unit. It is extremely important that you record your ser...
Page 22: Parts List
Parts list model #97008 griddle, built-in, l.P. (propane) model #97009 griddle, built-in, n.G. (natural gas) how to order replacement parts please refer to the parts list on this page. To make sure you obtain the correct replacement parts for your gas griddle, the following information is required t...
Page 23: Exploded Illustration
Exploded illustration 22.
Page 24: Limited Warranty
Limited warranty registering your griddle in order to validate your bull limited warranty, you must complete the warranty registration card within 90 days from the proof of purchase. You may register your unit either online at www.Bullbbq.Com or by sending in the completed hard copy along with a cop...