Summary of DELUXE 200
Page 2
Warranty for most vehicles we have a t-harness available to make your remote starter installation quicker and easier. To order visit us online at www.Directwholesale.Net . Additional remote transmitters can be purchased through direct wholesale at www.Directwholesale.Net . For a full list of bulldog...
Page 3
Installation table of contents 3 42 required tools ..........................................................................5 installation check list ...........................................................5 technical assistance ...............................................................6 be...
Page 4
Table of contents 4 41 h4/8 lt. Green/black wire - (-) 200ma programmable output ..........19 dual pulse door unlock output factory security disarm signal output start status (by-pass control) output h4/9 blue/black wire - (-) 200ma ignition 3 control output .............19 gm vats key override h6 2...
Page 5
5 required tools 40 unless your remote starter includes a bonus installation kit you will need the following items: a sharp knife, electrical tape and a computer-friendly test light. A 5/16 inch drill bit may be needed to install the hood pin switch. If the bottom of your dash on the drivers side w...
Page 6
6 39 it is recommended that a carbon monoxide detector be installed in the living area near a location where the vehicle may be garaged. Since there are many different makes and models of vehicles, visit our website, www.Bulldogsecurity.Com. Read this manual thoroughly before starting the installati...
Page 7
7 38 precautions do not mount the control module until all connections have been made and tested. Please use caution: do not cut, probe or disconnect the vehicles airbag wires. These wires will almost always be inside a bright yellow tube located near the steering column harness. Warning! On vehicl...
Page 8
8 37 to operate your test probe, connect the black clip to a good chassis ground . Then connect the red clip to a good 12v (+) positive source. If the test probe is connected correctly, both the green and the red lights will be dimly illuminated. If a (+) positive source is probed, the red light wil...
Page 9
9 36 operation b.Lock doors: 1. Press button on the transmitter. 2. The horn will chirp once and parking light will flash once indicating that the vehicles door is locking. Silent locking / unlocking doors: press the transmitter and buttons at the same time will lock or unlock the vehicles doors, ...
Page 10
35 10 important owners notice warnings: as with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of childrens reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Aler...
Page 11
11 34 testing your installation note: a second 1n4003 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (non stripped) side must be connected to the grey (h4/4) wire of the re...
Page 12
12 33 testing your installation method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than park or neutral while the key is in the ignition cylinder however, the original factory key in chime module will not alert the owner th...
Page 13
13 32 note: if the optional remote starter enable toggle switch is installed, connect the one side of the switch to this reference wire the other side of to the thin black neutral safety switch wire (h4/2) of the remote start unit. The reference diagram below shows a typical gm b body ecm reference ...
Page 14
14 31 testing your installation mechanical neutral safety switch considerations: mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selec...
Page 15
15 30 testing your installation: caution!! The follow procedure must be performed after the installation of the remote start device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property...
Page 16
16 29 3. Press and hold the and buttons at the same time on the transmitter for 5 seconds, there will be a confirmation of (6) chirps with (3) long chirps and the led turns on for (2) seconds to confirm the system feature programming all returns to factory default setting. Programming shutdown diagn...
Page 17
17 28 programming start timer programming: (test and adjust) 1. Press the button twice on the transmitter to start the vehicle. 2. If everything goes well: wait for 15 seconds: a. If the engine is still running. I. Press the button twice on the transmitter to stop the engine from running. You have c...
Page 18
18 27 programming 4. Within (10) seconds, start the vehicle with the key. (while the engine is running, the parking lights and led will flash, if they are not flashing please check violet/white wire connection. 5. Press and hold the program switch for (2) seconds until a long chirp and the led light...
Page 19
19 26 programming feature iv proramming: 1. Turn the ignition 'switch on/off (3) times and leave in the off position. 2. Push the program switch (8) times and hold in on the 8th push until (4) chirps with a long chirp is heard then release the program switch. You are now in the start feature ...
Page 20
20 25 programming feature #iii programming chart one chirp with press one led pulse transmitter factory default two chirps with three chirps with four chirps with button setting two led pulses three led pulses four led pulses 1 gasoline n/a n/a n/a engine 2 20 minute 30 minute 5 minute 10 minute run...
Page 21
21 24 feature #ii programming chart one chirp with press one led pulse transmitter factory default two chirps with three chirps with button setting two led pulses three led pulses 1 pathway illumination parking light turns on parking light turns on feature off for 30 seconds upon for 30-second...
Page 22
22 23 programming feature #i programming chart one chirp with press one led pulse transmitter factory default two chirps with three chirps with four chirps with button setting two led pulses three led pulses four led pulses 1 chirps on chirps off 2 0.8 second 3.5 second double pulse door lock with d...