Summary of DELUXE 200B
Page 2
Installation tips and accessories for most vehicles we have a t-harness available to make your remote starter installation quicker and easier. To order visit us online at www.Directwholesale.Net. Additional remote transmitters can be purchased through direct wholesale at www.Directwholesale.Net. For...
Page 3
3 transponder / passlock iii 62 required tools ....................................................................... 5 installation check list ........................................................ 5 technical assistance ............................................................ 6 before you b...
Page 4
61 4 transponder / passlock iii note: if the vehicle does not start with the remote starter or runs for approx 5 seconds and shuts down, try adjusting or changing the position of the transponder key in the bypass module or adjusting the position of the (2)two loop antenna wire around the transponder...
Page 5
5 60 routed through the steering column and up towards and then around the ignition key cylinder and needs to be positioned so that there are at least (2)two turns (the more turns the better chance the signal will be received by the factory receiver antenna) around the ignition key cylinder as shown...
Page 6
6 transponder / passlock iii purchase one through jbs technologies, but make sure they program all keys to the vehicle since learning just one transponder could erase all other key transponders (including the key used for the bypass module). Again, an extra programmed transponder ignition key that s...
Page 7
7 saturn transponder / passlock iii vats, ‘smart key’, passlock iii, sentry key, securi- lock and others, are all transponder systems: note: for this type of anti-theft system – you must sacrifice one of your spare programmed transponder ignition keys that starts this vehicle. This extra tran- spond...
Page 8
57 8 cut the pink wire in half and connect as shown. Turn all dip switches off. When connecting the anti-theft bypass module to your remote starter, you will need to activate this bypass module by connecting it in different ways depending on the remote starter you have. Attach the white/green (-)sec...
Page 9
Passlock ii 9 saturn saturn vehicles (1996-2000) with factory keyless entry have a unique anti-theft system. Locate the factory alarm module located behind the right rear quarter panel (trunk area). Connect the pink and yellow/black wires of connector “j and d” of the factory anti-theft module as sh...
Page 10
10 with the probes held firmly – dial-in the final resis- tance value needed for your system by turning the screw on the variable resistor on the side of the unit next to the dip switches. Turn the screw until the re- sistance value matches the resistance value of the key. Connect the bypass module ...
Page 11
11 54 turn the key to the “run” position and place the vehicle in reverse. Turn the key to start, then release the key to the “run” position and measure the resistance between the key side of the yellow wire (this wire will show 1 to 6 v dc on a volt/ohm meter) and the orange/black wire or black wir...
Page 12
53 12 passlock i passlock ii remove the lower steering column cover on the steering column. Locate the (3)three small 20 gauge wires (yel- low, orange/black sometimes black and red/white wires) coming out of the ignition key cylinder of the steering column, these wires are usually wrapped in black f...
Page 13
13 52 connector (between the heavy gauge red and red/white wires), in the main ignition switch harness. Note ** this is a different wire than the black ground wire mentioned in the above steps. Connect the bypass module using the diagram be- low. Be sure to tape up any connections, do not leave any ...
Page 14
51 14 passlock i cut the yellow wire in half and strip back both ends. Remove some of the insulation on the black wire without cutting the wire and the white wire is not used!!. Put the vehicle into reverse then turn the ignition key to the start position and release it to the run posi- tion. The ve...
Page 15
15 50 vats passlock i remove the lower steering column cover on the steering column. Locate the (3)three small 20 gauge wires (yel- low, black and white wires in a gray or black plug) coming out of the ignition key cyl- inder on the bottom right hand side of the steering column. 1. 2. Wiring connect...
Page 16
49 16 vats white or (1) white/black striped and (1)purple/black striped) 20 gauge wires, these wires are often in a orange or black plas- tic tube. Be careful not to cut into the yellow air bag wires! The air bag wires are often in a yellow plastic tube that is clearly marked. The vats wires run fro...
Page 17
17 48 vats measure the resistance of the little pellet on the ignition key. It should be between 392 ohms and 11,800 ohms. To do this, put the ohm meter probes on each side of the key pellet. The resistance value should be close to one of the following (all values in ohms): 392, 523, 681, 887, 1.13k...
Page 18
47 18 use this chart for vats, passlock i & passlock ii 1 - 8-pin harness dip switch # 2 3 4 5 6 resistor value 0.825 1.65 3.32 6.65 13.3 final resistance (k ohms) on on on on on 0.000 +trimpot value off on on on on 0.825 +trimpot value on off on on on 1.650 +trimpot value off off on on on 2.475 +tr...
Page 19
19 46 list of vehicles and types of security systems dodge 300 m 99+ transponder pontiac sunfire 2000 passlock ii dodge intrepid 98+ transponder porsche (all 97+) transponder dodge neon 2000 transponder saab (all 97+) transponder ford contour 97+ transponder saturn 97+ factory ford crown vic 96+ tra...
Page 20
45 20 list of vehicles and types of security systems acura 3.2tl 98+ transponder gmc suburban 98+ passlock ii acura rl 98+ transponder gmc sonoma 98+ passlock ii audi a4, a6,a8 98+ transponder gmc sierra 98+ passlock ii bmw (all 97 +) transponder gmc safari 98+ passlock ii buick century 97+ vats gmc...
Page 21
21 44 model if114 vats/passlock/transponder universal alarm bypass module this module lets you bypass virtually any type of vehicle anti-theft system on the market today to remotely start your vehicle without permanently disabling the vehicle’s factory anti-theft system. In 1985, general motors came...
Page 22
43 22 wiring connections vacuum oper- ated door locking system: typical of mercedes benz and audi. Locate the wire under the driver’s kick panel. Use the voltmeter connecting to ground, verify the you have the correct wire with the doors unlocked, the voltmeter will receive “12 volts”. Lock the door...
Page 23
23 42 wiring connections h6/2-pin blue connector for the program switch select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch does not have to be concealed, how- ever, concealing the switch is always recommended. Route the program switch wires t...
Page 24
41 24 programming alarm feature. #1 programming: turn the ignition switch from “on” to “off” (3) times and leave in the “off” position. Push the programming switch (2) times and on 2nd push hold it until (1) chirp followed with a long chirp is heard, then release the switch. You are now in the “alar...
Page 25
25 40 programming feature ‘ii” proramming: turn the ignition switch “on/off” (3) times and leave in the “off” position. Push the program switch (4) times and hold in on the 4th push until (2) chirps with a long chirp is heard then release the program switch. You are now in the feature “ii” programmi...
Page 26
39 26 programming feature #iii programming turn the ignition switch “on/off” (3) times and leave in the “off” position. Push the program switch (6) times and hold in on the 6th push until (3) chirps with a long chirp is heard then release the program switch. You are now in the feature “iii” programm...
Page 27
27 38 programming feature ‘iv” programming: turn the ignition ‘switch “on/off” (3) times and leave in the “off” position. Push the program switch (8) times and hold in on the 8th push until (4) chirps with a long chirp is heard then release the program switch. You are now in the start feature “iv” p...
Page 28
37 28 programming within (10) seconds, start the vehicle with the key. (while the en- gine is running, the parking lights and led will flash, lf they are not flashing please check violet/white, wire connection. Press and hold the program switch for (2) seconds until a long chirp and the led light wi...
Page 29
29 36 programming start timer programming: (test and adjust) press the button twice on the transmitter to start the vehicle. If everything goes well: wait for 15 seconds: if the engine is still running. Press the button twice on the transmitter to stop the engine from running. You have completed thi...
Page 30
35 30 programming press and hold the and buttons at the same time on the trans- mitter for 5 seconds, there will be a confirmation of (6) chirps with (3) long chirps and the led turns on for (2) seconds to confirm the system, feature programming all returns to factory default setting. Shutdown diagn...
Page 31
31 34 testing your installation testing your installation: caution!! The follow procedure must be performed after the installa- tion of the remote start device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the follow- ing manner may resul...
Page 32
33 32 testing your installation mechanical neutral safety switch considerations: mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start de- vice. Often when the ignition switch is turned off while the gear sel...