1. DL manuals
  2. Bulldog Security
  3. Remote Starter
  4. RS1300E
  5. Installation And Owner's Manual

Bulldog Security RS1300E Installation And Owner's Manual

Summary of RS1300E

  • Page 1

    Contents alarm and remote control starter model rs1300e installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:...

  • Page 2

    System features system components 1 required tools your system includes: 2- four button remote transmitters 1- main control module 1- 16-pin wire harness 1- 5-pin door lock harness 6- heavy gauge wires w/ spade connectors 1- hood pin switch 1- extended range antenna 2- window antenna clips 1- warran...

  • Page 3

    Technical assistance before you begin 2 precautions this system is designed for use with vehicles equipped with fuel-injected, gasoline engines with automatic transmissions only. Safety first! Never remotely start your vehicle indoors, with the keys in the ignition or unless the transmission is in p...

  • Page 4

    Making wiring connections 3 using your test probe to operate your test probe, connect the black clip to a good chassis ground. Connect the red clip to a good 12v positive source. If the test probe is connected correctly, both the green and the red lights will be dimly illuminated. If a positive sour...

  • Page 5

    4 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower...

  • Page 6

    5 note: remove any paint below the spade connector. Factory bolt spade connector black ground wire 1. If your vehicle has only one (1) ignition wire, as most 1993 and older domestic and import vehicles do, connect the heavy gauge white wire to it. 2. If your vehicle has two (2) ignition wires, as mo...

  • Page 7

    6 neutral safety switch parking lights (+12v only with parking lights on) turn the parking lights to the on position. (not your headlamps). Probe the wire(s) coming from your headlamp control switch. The correct wire will show +12v and the red light will glow bright only when the parking lights are ...

  • Page 8

    7 connecting the wiring harness antenna placement optional connections ground pre-1996 gm rear wheel drives with purple crank wire optional part #775 required. Ground 86 30 87a 87 85 5 amp fuse tie into heavy white wire on 4-relay harness (-) negative hood pin wire message center or key buzzer drive...

  • Page 9

    8 light will glow bright on both the lock and the unlock wires. Press and hold the lock button on the switch and test the lock wire. The correct wire will test (+) positive and the red light will glow bright. Release the lock button and this wire should show a (-) negative and the green light will g...

  • Page 10

    Operator programming instructions 9 note: when testing the door pin wire, make sure the dome light is on. Some vehicles, if the door is left open for a period of time, the dome light will go out, resulting in a false reading. Dome light to determine if your dome light is turned on with (+) positive ...

  • Page 11

    10 adding additional remotes press and hold brake. Next, press and hold button #1 on the working remote until the parking lights flash once, release. Press and release button #4 on the new remote. The parking lights will flash three (3) times confirming that the new remote was learned. Cold start on...

  • Page 12

    How to use your remote transmitter 10 automatic start - on press and hold brake. Press and hold button #2 until the parking lights flash twice. Release. Press and release button #1. The parking lights will flash once. The automatic start is programmed on. Release the brake, the parking lights will f...