1. DL manuals
  2. Bulldog Security
  3. Car Alarm
  4. RS602E
  5. Installation And Owner's Manual

Bulldog Security RS602E Installation And Owner's Manual

Manual is about: Bulldog OWNER'S GUIDE REMOTE STARTER ALARM

Summary of RS602E

  • Page 1

    Contents alarm and remote starter • model rs602e installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:00 p.M....

  • Page 2

    System features system components 1 required tools 2 four-button extended range remotely start your car to run the heater or air conditioning from an extended distance. Remote control keyless entry remotely locks and unlocks your power door locks. Built in alarm features provides door and hood prote...

  • Page 3

    Technical assistance should you need help. First check our website at www.Bulldogsecurity.Com/wires.Htm or call our toll-free tech support hotline monday through friday 9am-8pm and saturday 10am-4pm est at 800-878-8007. You must give the following information: •name •telephone number with area code ...

  • Page 4

    3 making wiring connections 4. Insert the wire from the unit through the hole as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire ti...

  • Page 5

    4 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower...

  • Page 6

    5 accessory wire(s) that power the heater/blower motor (+12v in run or on positions) this wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible. Most vehicles will have (1) accessory wire; how...

  • Page 7

    6 antenna placement e model remote starters run the antenna up the windshield pillar on the driver’s side and across the top of the windshield to the center, behind the rearview mirror. Use the antenna clips provided to hold it in place. Be sure to expose the full length of the clear antenna. It wil...

  • Page 8

    7 connecting the 18-pin harness & 4-relay harness factory anti-theft systems for general motors cars only system 1: passkey i and ii system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a test meter. A bypass module is available, part #vats-wr module...

  • Page 9

    8 (-) negative dome light type (all other vehicles) connect the violet wire from the 18-pin harness to the white wire on the optional #775 relay harness. Connect the black wire on the optional relay to +12v constant fused at 5 amps. Connect the blue wire to ground. Connect the yellow wire to the dom...

  • Page 10

    9 horn honk output (-) (optional part #775) the existing horn wire will usually be found in the main ignition switch harness in the steering column. Probe for a wire which will remain neutral (in some cases may show a (+) positive). When the horn is pressed this wire will test as a ground or (-) neg...

  • Page 11

    Connecting “type b locks” • if your vehicle has a “type b” door locking system, connect the green with black stripe wire from the 18-pin harness to the door lock wire. Connect the brown with black stripe wire to the unlock wire. See diagram below. “type b” - negative type door locks used on most imp...

  • Page 12

    11 installation programming: programming tach/tachless start press and hold the brake, then press and hold button #3 (trunk) until the parking lights flash three (3) times. Release button #3. Press and release button #4, the parking lights will flash once. The unit is now in tachless start mode. Pre...

  • Page 13

    12 note: only cold and hot start functions can be enabled at the same time. If button #1 is pressed for programming, cold/hot start is disabled. When buttons #2 and #3 are pressed, then the automatic and low voltage starts are disabled. Special programming mode: valet mode on press and hold the brak...

  • Page 14

    13 keyless entry operation press button #2 (lock/unlock), the parking lights will flash once and the doors will lock. Press button #2 again, the parking lights will flash twice, the doors will unlock, and the parking lights will remain on for one minute or until you turn the ignition on or press the...