1. DL manuals
  2. Bully Dog
  3. Automobile Electronics
  4. GT for Hemi Plus
  5. Installation Manual

Bully Dog GT for Hemi Plus Installation Manual

Summary of GT for Hemi Plus

  • Page 1

    Custom gauge pods installation manual triple dog™ gt gas triple dog™ gt diesel watchdog™ gt for hemi plus gt gas (40415), gt diesel (40420) and gt hemi plus (40430) are not legal for sale or use in california on pollution-controlled vehicles..

  • Page 2: Introduction

    1 introduction these custom gauge pods offer a clean, seamless oem fit in a convenient and safe location for bully dog performance products like the gt and watchdog. Table of contents gauge pod assembly diagrams ........................ 3-4 gt and watchdog ..............................................

  • Page 3: Tools Needed

    2 tools needed 31302 phillips screwdriver flat-head screwdriver 8 or 10 mm socket socket wrench 31303 phillips screwdriver 10 mm socket socket wrench 31304 flat-head screwdriver rachet 9/32 socket w/ extension 33302 and 33303 (optional) drill 13/64″ drill bit 32304 phillips and/or flat-head screwdri...

  • Page 4: Gauge Pod Assembly Diagrams

    3 gauge pod assembly diagrams gt/watchdog when assembling, consider the following: • will the custom mount be painted? If so, paint the mount before assembly. Important: a gauge pod adapter (sold separately, part #30420) is required to mount a gt or watchdog unit with a custom pod mount. Gt/watchdog...

  • Page 5: Pmt

    4 pmt when assembling, consider the following: • will the custom pod be painted? If so, paint the mount before attaching cradle assembly. • the cradle mounting plates can be painted to match the custom mount. • painting the pmt cradle is not recommended. Pmt cradle front mounting plate back mounting...

  • Page 6

    5 31302: ford f-series super duty 2003-2007 1. Remove the two plastic caps on the grab handle on the driver’s side. 2. Remove the four bolts that were under the caps. (use an 8 or 10 mm socket.) 3. Pull out the weather stripping around the a-pillar (so it can be pulled down easily). 4. Release the t...

  • Page 7

    6 5. Pull the a-pillar down to access the screws that secure the grab handle. 6. Remove the two grab handle screws. (use a phillips screwdriver.) a. The grab handle will separate from the a-pillar. B. Set the grab handle and screws aside. 7. Push the stock a-pillar back into its original location. A...

  • Page 8

    7 31303: ford f-series super duty 2008-2012 1. Attach the gt, watchdog or pmt to the custom pod. A. See the diagrams on pages 3 and 4. 2. Install any necessary cables before placing the pod mount. A. Make sure the cable(s) will reach the pod mount location. B. Hide the cable(s) behind the dash or we...

  • Page 9

    8 4. Place the pod mount in the correct position. (see the figure a.) 5. Firmly press down on the parts of the pod mount where the adhesive tape touches the dash for a secure attachment. Place pod mount figure a.

  • Page 10: 31304: Ford Sd 2011+

    9 31304: ford sd 2011+ installation existing trim removal 1. Place flat head screwdriver in the middle of each side of the cap and open cap, taking care not to damage stock a-pillar. 2. Using a 7mm socket with extension and ratchet; unscrew the two bolts securing the stock a-pillar where the caps we...

  • Page 11

    10 3. Pull back weather stripping in the area of the a-pillar and remove the side panel of the dash by the driver door. 4. Run cables as needed through the dash to the custom pod. Install the custom gauge pod by first aligning the tab into the slot on dash. Guide custom gauge pod so the screw hole l...

  • Page 12: 32303: Dodge Ram

    11 32303: dodge ram ® 2003-2009 1. Remove the bolt that holds the stock a-pillar in place. A. It is located about halfway down the pillar behind a small oval cover. B. Remove the cover piece and set it aside. C. Use a 10 mm socket. 2. Pull out the weather stripping around the a-pillar (so it can be ...

  • Page 13

    12 4. Peel the clear strip(s) off the adhesive tape on the back of the pod mount. 5. Position the custom gauge pod over the stock a-pillar. (do not attach or secure it yet.) 6. Route all wiring under the gauge pod (and under the dash, if necessary). 7. Slide the pod down until the pod screw hole lin...

  • Page 14: 32304: Dodge Ram® 2010+

    13 32304: dodge ram® 2010+ 1. Remove the bolt that holds the stock a-pillar in place. A. It is located about halfway down the pillar behind a small oval cover piece. B. Remove the cover piece and set it aside. C. Use a 10 mm socket. 2. Pull out the weather stripping around the a-pillar (so it can be...

  • Page 15

    14 step 3 is for pmt only. 3. Attach the pmt cradle to the custom pod. (see diagrams on page 4.) 4. Remove the small side panel on the side of the dash. (use a flat-head screwdriver.) step 5 is for pmt only. 5. Run the pmt wiring harness through the open part of the dash (see step 4). Pmt installs: ...

  • Page 16

    15 8. Line up the gauge pod. A. Be careful not to touch the pod to the vehicle (adhesive tape). B. The bottom of the pod should match the bottom of the a-pillar. Pmt installs: skip step 9. 9. Make sure that the hdmi cable is sticking out through the gauge hole. 10. Slide the pod down until the pod s...

  • Page 17

    16 12. Firmly press down on the parts of the pod mount where the adhesive tape touches the stock a-pillar for a secure attachment. 13. Replace the driver’s side dash panel and re-secure the weather stripping..

  • Page 18: 32305: Jeep Jk 2007-2010

    17 32305: jeep jk 2007-2010 existing trim removal 1. Using a no. 2 phillips, back out the plastic screw from the a-pillar trim. 2. Remove torx screws from the visor mounting bracket with the t20 torx bit. 3. Pull upper visor trim down/off. 4. Pull off the stock a-pillar. 5. You should now have expos...

  • Page 19

    18 custom pod mount install 6. Install the appropriate mount adapter and run cables for your vehicle through the accessory hole in the bully dog a-pillar as needed. (some route out through, while some mount back in before install) pull the driver side dash panel off to run cables under the dash to t...

  • Page 20: 32306: Jeep Jk 11+

    19 32306: jeep jk 11+ existing trim removal 1. First remove the visor trim following the step by step instructions below. 2. Remove torx screws from the visor mounting bracket with the t20 torx bit. 3. Pull upper visor trim down/off. 4. Pull off the stock a-pillar. 5. You should now have exposed the...

  • Page 21

    20 custom pod mount install 6. Install the appropriate mount adapter and run cables for your vehicle through the accessory hole in the bully dog a-pillar as needed. (some route out through, while some mount back in before install) pull the driver side dash panel off to run cables under the dash to t...

  • Page 22

    21 33306/33307: gm sierra/silverado 2007 (2014 1500 and 2013+ avalanche not included) 1. Remove the a-pillar trim screw. A. Remove the screw cover. B. Remove the screw. (use a 7 mm socket.) 2. Pull out the weather stripping around the a-pillar (so it can be moved easily). 3. Remove the stock a-pilla...

  • Page 23

    22 if the vehicle has a speaker attached to the a-pillar, the speaker will need to be removed before the trim piece can be completely removed. 4. To remove the speaker: a. Disconnect the speaker wire. (the plug is located about 4” away from the speaker.) b. Release the securing tabs by pushing them ...

  • Page 24

    23 8. Slide the pod over the stock a-pillar until they line up. A. If there is a speaker on the a-pillar, make sure that the speaker in the pod is placed directly over the speaker wire. 9. Reconnect the speaker wire. 10. Route all wiring down along the side of the dash. 11. Firmly press down on the ...

  • Page 25: Notes

    24 notes.

  • Page 26

    25 33302/33303: gm sierra/silverado 1999-2007 1. Remove the driver’s side dash panel. 2. Pull out the weather stripping around the a-pillar (so it can be moved easily). 3. Attach the gt, watchdog or pmt cradle to the pod. (see diagram on pages 3 and 4.) 4. Peel the clear strip(s) off the adhesive ta...

  • Page 27

    26 with a speaker, make sure that the speaker hole lines up so that it is directly over the speaker in the stock a-pillar. 6. Firmly press against the parts of the pod mount where the adhesive tape touches the stock a-pillar for a secure attachment. 7. Run all wiring down the side of the dash. 8. Re...

  • Page 28: Notes

    27 notes.

  • Page 29: Notes

    28 notes.

  • Page 30: Doc.# 31303-99 V1.3

    Doc.# 31303-99 v1.3 gauge pod adapter part #30420 prefilters and cleaning kit accessories sensor docking station see more products from bully dog technologies free technical support at: 866-bullydog (866-285-5936) see more at: bullydog.Com p ut in a h at.