Bunker Hill Security 61229 Quick Start Manual

8-Channel

Surveillance DVR 

with 4 Cameras & Mobile Monitoring Capabilities

Item 61229

FOR ADVANCED USERS

Internet Setup for Remote Use

INITIAL SETUP

Physical Connections 

Quick Start Guide

PORT FORWARDING

SMARTPHONE 

ACCESS

Local Area Network (LAN) Setup 

Set Date and Time

In DVR 

Main Menu

Select System

Set Recording Mode

Motion Detection Settings 

Manual

Which 

Recording 

mode?

1

2

4

@

Bunker Hill Security

®

B1

B2

B3

B4

D2

D3

D4

B5

B1

B2

B1

B2

B1

B2

D5

D1

USB Port  

Video Input

A

B

C

B

C

D

A

Connect 

Monitor  

Connect 

Cameras

Connect 

Mouse 

 Power Input

Video Output

Connect  

Power  

D

BNC/RCA

VGA

Select

General

Set Date and 

Time above

Set Date and 

Time

Click Apply 

then OK 

Scheduled

In DVR 

 Main Menu 

select Record

Press REC on 

front of DVR - 

red light will 

flash    

Select 

Schedule

Select Channel 

and Day of 

Week

Select boxes 

for Normal and 

Motion

On PC, go to Start 

Menu, click Run. 

In DOS window

type “cmd”, click OK.

type “ipconfig”

press ENTER

STOP

Ensure you have a 

Windows® PC with 

Internet Explorer® 

and a Router before 

proceeding.

NO

Connect DVR to 

Router via 

 Ethernet Cable 

(Sold Separately)

From DVR Main Menu 

select 

Network > Network

Type = Static

Find the Router’s LAN

Write down:  

1. Subnet Mask 

2. Default Gateway 

(Router’s IP Address)

In DVR Network > Network 

change settings:

1. Client Port: 3000

2. HTTP Port: 3001 

3. New IP Address

4. Subnet Mask you wrote down

5. Default Gateway you wrote down

6. DNS1 same as Gateway

Change last 3 digits 

to a number between 

200 and 255

Change last 3 digits 

to a number between 

100 and 255

Click Apply then OK 

to save changes.

Click Exit, DVR will prompt 

restart. Click OK.

After restart, 

on DVR go to 

Network > Network 

to view settings.

Open Internet Explorer®. 

In address bar, type in 

DVR’s IP Address and HTTP Port:

http://xxx.xxx.xxx.xxx:3001  

(where x = IP Address and 3001 = HTTP Port)

Press Enter.  

Allow ActiveX Control to install.

You may need to adjust the settings in 

Internet Explorer® by adding the http 

address to Trusted Sites and modifying 

ActiveX controls to allow installation.

After ActiveX Control installs, 

Log in to DVR 

with User Name and Password.  

@

WARNING

This Quick Start Guide is not intended to

replace the Owner’s Manual & Safety 

Instructions. To prevent serious injury, read 

all safety warnings and instructions therein 

to ensure proper usage.   

In DVR 

Main Menu

Select System

Select

Users

Set User Name 

and Password

Click Apply 

then OK 

3

 Repeat for all 

Days and all 

Channels

Click Apply 

then OK 

In DVR 

Main Menu

Select Alarm

Select

Motion

Select 

Channel

Set Sensitivity 

Level

Select Area

Select which 

Channels 

will record 

Click Apply 

then OK 

Set Buzzer for 

audible alarm

Set Date and 

Time above

Set Recording 

Mode above

Wide Area Network (WAN) Setup 

REMOTE

COMPUTER 

ACCESS

E

Mount 

Cameras

Note:  Monitor and 

Surge Protector 

sold separately.

Set up LAN 

according to 

instructions above.

Log in to the Router 

and go to 

Port Forwarding or 

Applications and 

Gaming.

Set start port to 3000 

and end port to 3002.  

Set up both UDP and 

TCP protocols if the 

option is given.

Open Internet Explorer®. 

In address bar, type in 

Default Gateway  

(from LAN Setup above).

Example: xxx.xxx.xxx.xxx

Press Enter.  

Find theRouter’s IP 

Address by going to 

whatsmyip.com.  

Write it down.

On remote computer, 

Open Internet Explorer®. In address bar, 

type in Router’s IP Address 

and HTTP Port (from LAN Setup above):

http://xx.xxx.xxx.xxx:3001  

(where x = IP Address and 3001 = HTTP Port)

Press Enter.  

Allow ActiveX Control to install.

You may need to adjust the settings 

in Internet Explorer® by adding the 

http address to Trusted Sites and 

modifying ActiveX controls to allow 

installation.

After ActiveX Control installs, 

Log in to DVR 

with User Name and Password 

(from LAN Setup above).  

Insert supplied CD 

into computer and look in 

Mobile Software 

folder for instructions.

In DVR 

Main Menu

Select Network 

then Mobile

Set User Name 

and Password

Set Mobile Port 

to 3002

Click Apply 

then OK 

Do you have a 

Windows® PC with 

Internet Explorer® 

and a Router?

YES

YES

NO

Create New IP 

Address:

Are last 3 digits of 

Default Gateway 

between 0-99?

See Manual - Page 12

See Manual - Page 17

See Manual - Page 18

See Manual - Page 19

See Manual - Page 28

See Manual - Page 30

Ethernet

Connection