Owner’s manual for the ground driven spreader c-dit400 c-dax ltd po box 1010, 145 harts road tiritea, palmerston north ph:06 354 6060 fax:06 355 3199 e-mail: sales@c-dax.Co.Nz www.C-dax.Co.Nz.
2 safety precautions cdit400 an important message for owners & operators of c-dax attachments/accessories be warned of the dangers of loading your atv or other vehicle in excess of its carrying capacity. It is important to understand that any loads or attachments whether fastened to or placed on a v...
3 safety precautions before attempting to install or operate the equipment, read and understand the manual thoroughly. Failure to comply with this instruction constitutes improper use and will invalidate the warranty. Throughout this manual there are highlighted text boxes containing warnings, cauti...
4 c-dax cdit400 owner’s manual (pt.No.2400-5610 issue 8 dated 02 dec 2010) table of contents 2 safety precautions 4 table of contents 5 introduction description specifications order information warranty 6 liability 7 operation 8 calibration magnesium oxide 9 operating the spreader adjusting the spre...
5 introduction congratulations. You have just purchased an advanced spreader from c-dax ltd. C-dax ltd is committed to providing you, the farmer, with quality applicating systems. Description the c-dax c-dit400 is a ground-driven spreader designed for application of pelleted fertilisers. It can also...
6 liability the maximum liability, which is accepted by c-dax ltd, is limited to replacement of faulty goods only. Every care has been taken in the manufacture of our goods but because use of the goods is outside the control of the manufacturer, the end user assumes all responsibility for the use. N...
7 operation the product to be spread is placed in the hopper. When the spreader is towed forward, the right hand wheel drives through the lever operated mechanical clutch and gearbox to turn the spinner in a clockwise direction. When the control handle is in the disengage position (fully back) the c...
8 calibration 1. Ensure the control handle is fully back (clutch disengaged, shutter closed). 2. To calibrate your spreader, place a measured amount of product (10 kg) in the hopper. 1. Set the shutter stop lever to the position (1-9) indicated in the calibration guides below. Hole position 9 (shutt...
9 operating the spreader when the spreader has been correctly calibrated, the hopper may be filled to the required level and spreading commenced. To reduce agitator damage to product and to ensure that product is not forced past the agitator shaft when towing the spreader to the area to be treated, ...
10 maintenance the following maintenance actions are mandatory for reliable use of the spreader. Before use check the tyre pressures and charge with air as required. The correct pressure is 15psi (100kpa). Disengage the clutch by ensuring the control lever is fully back then turn the spinner by hand...
11 parts diagram.
12 parts list item no. Qty. Part no description 1 1 2550-1400 drawbar-asy-cdit400 2 1 3500-5700 cdit400 frame-gl 3 1 7500-2160 hopper-cdit400gt-mdpe 4 1 7500-2500 lid-full-cdit400gt-mdpe 5 1 9200-4600 wheelasy-18x950x8-keyed-knobbly 6 1 9200-4500 wheelasy-18x950x8-bearing-knobbly 7 2 7500-2590 mudga...
13 46 4 2810-0880 bolt-m8x80-ss 47 1 3290-1275 screw-hh-m12x75-zp 48 1 1300-3010 bkt-clutch-cdit400gt-zp 49 9 3310-6010 washer-flat-m10-zp 50 1 2000-3037 clamp-hose-oetiker3740-zp 51 2 2890-0816 screw-cap-m8x16-grade12.9 52 1 5270-0003 nipple-grease-m6x1x5-cp 53 2 2890-0812 screw-cap-m8x12-grade12.9...
