Summary of CS9000 MK2
Page 1
Cs9000 mk2 operating instructions.
Page 2
Cs9000 mk2 - rapid get you going instructions searching for a metal object 1. Turn mode switch to batt. Chk and check condition of the battery on meter. 2. Set threshold to the centre of the normal band. 3. Set signal balance to the centre of the normal band. 4. Set ground balance to the centre of t...
Page 3: User Notes
User notes 2.
Page 4: Contents
Contents page introduction 5 assembly instructions 5 batteries 5 controls 7 mode switch 7 threshold 8 signal balance 8 ground balance 9 automatic threshold 9 headphone jack socket 9 thumb set 10 features 10 automatic threshold 10 ground balance 10 cs9000 mk2 operation 10 ground balancing metal mode ...
Page 5
Controls c-scope cs9000 mk2 4.
Page 6: Introduction
Introduction to protect your investment complete both sections of the enclosed guarantee card and return the reply paid portion to c-scope. This is particularly important in order to obtain the free parts guarantee. (uk and eire only) please retain the original packing box. In the event that your de...
Page 7
2. Insert the small foam squares inside the two springs on the lid, and also the two springs in the holder, this will prevent the loss of spring tension. 6.
Page 8: Controls
Controls mode switch pwr off the first position on the mode switch is the power off setting. Be sure the switch is returned to this position after using the detector. Failure to do so will result in the batteries being discharged. Metal in this mode the ground balance is in operation and all metal o...
Page 9
Threshold this control adjusts the audio tone volume of the background noise, commonly called ‘threshold’. To adjust this to optimum, the sound should be barely audible. When using headphones, the control will be set lower than when using the speaker. It may be necessary when using the speaker where...
Page 10
Ground balance this control is only effective when the metal mode is selected. It is adjusted to cancel out the mineralisation in the ground and allow for maximum penetration. For higher mineralisation the control is rotated towards the (+) sign and subsequently towards the (-) sign for reduced mine...
Page 11: Features
Thumb set the thumb set control is located at the tip of the handle. When using the cs9000 mk2 without the auto feature, the control may be pressed to the momentary position quickly with the loop over a target reducing the intensity of the signal making it easier to pinpoint. Further discussion of t...
Page 12
Ii. Remove all metal objects from your person such as belt buckles, car keys, watches, knives, etc. Iii. Hold the detector at arms length by your side in a comfortable carrying position, resulting in a distance of approximately 18 inches from the ground. Keeping the instrument level, press the thumb...
Page 13: Accessories (Optional)
Pinpointing in the automatic threshold off position, a surface target can appear to be very large, which is normal. Now the target must be ‘narrowed down’ to determine its’ location more accurately. Start to pass over the target from one direction, when the meter goes ‘off scale’ press the thumb set...
Page 14
The importance of the right approach treasure hunting can be a profitable and rewarding hobby, if approached in a patient and diligent manner. Time spent researching to locate a worthwhile site for a search can be time wasted if your search is hasty and erratic. To achieve maximum results it is impo...
Page 15
Range. Similarly, if you work slowly and carefully you should be able to distinguish the faint signals as well as the clear-cut signals and further increase your finds. The technique of getting the best out of your detector is not learnt overnight. You need to get as much experience as possible so t...
Page 16
Code of conduct for metal detector users 1. Do not trespass. Ask permission before venturing on to any private land. 2. Respect the country code. Do not leave gates open when crossing fields, and do not damage crops or frighten animals. 3. Do not leave a mess. Use a sharpened trowel or knife to cut ...
Page 17: Care of Your Detector
Care of your detector storage when not in use your detector should be stored in a dry warm environment. If it is not to be used for a certain length of time it is advisable to remove the batteries to avoid leakage which could cause serious damage. The working life of your detector will be shortened ...
Page 18: Specification
17 the detector drifts out of tune (a) temperature drift caused by change in air temperature when a machine is moved from a house or car into the open. The greater the change in temperature the more the drift, and in severe conditions up to 30 minutes may be needed for the electronic circuitry to ac...
Page 19
Kingsnorth technology park, wotton road, ashford, kent tn23 6ln telephone: +44 (0) 1233 629181 fax: + 44 (0) 1233 645897 www.Cscope.Co.Uk email info@cscope.Co.Uk issue 1 (7/01) b1062.