Summary of MAESTRO 2M
Page 1
Operator's manual maestro 2m pcb separator.
Page 2
2 2 description type pcb separator maestro 2m edition: 10/2017 - part no. 9008885 copyright this documentation as well as translation hereof are property of cab produkttechnik gmbh & co. Kg. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentio...
Page 3
3 table of contents 1 introduction ............................................................................................................................................ 4 1.1 instructions ............................................................................................................
Page 4
4 4 1.1 instructions important information and instructions in this documentation are designated as follows: danger! Draws your attention to an exceptionally grave, impending danger to your health or life. ! Warning! Indicates a hazardous situation that could lead to injuries or material damage. ! A...
Page 5
5 • always have service work done in a qualified workshop, where the personnel have the technical knowledge and tools required to do the necessary work. • there are various warning stickers on the device. They draw your attention to dangers. Warning stickers must therefore not be removed, as then yo...
Page 6
6 6 by using the maestro 2m pcb separator, pre-scored pcb's are cleanly and economically separated. Wear resistant blades and guides made from special steel ensure a long working life without adjustment. Adjustment of the guides can be quickly and easily carried out. The lower blade of the maestro 2...
Page 7
7 3 installation 3.1 unpacking and setting-up the device lift the device out of the box. check device for damage which may have occurred during transport. set up device on a level surface. check delivery for completeness. Contents of delivery: • pcb separator • power cable • 2 fuses t 1,0 a ...
Page 8
8 8 3 installation 3.3 height adjustment of the upper blade i notice! Toavoidpossibledamageonthebladesduringtransporttheupperblade(4)isfixedinthe"parkposition" so that there is a maximum distance to the lower blade. set the upper blade into the working position before switching on the machine. 4 5...
Page 9
9 3 installation 3.4 adjustment of the stop of the upper blade i notice! The lower stop of the upper blade adjustment is already adjusted by delivery. after a long operation time, while working at strongly varying temperatures or else after replacing a blade, it is recommended to re-adjust the low...
Page 10
10 10 4 operation 4.1 switching on the machine switch the machine on. The mains power switch (1) is situated at the rear of the machine in the mains module. After switching on the display (2) of the control panel shows "0". 1 5 3 4 2 6 9 7 10 8 fig. 7 operation 4.2 setting the speed of separation ...
Page 11
11 4.4 error treatment the device has an overload protection which will switch the motor off. Error message cause remedy display "f" overload • when trying to cut beside the pre- scored groove • when a component on a pcb are jammed between the blades the cutter drive will perform a short backward mo...
Page 12
12 12 5 blade replacement danger! unplug power cord before starting maintenance operation. ! Warning! Risk of hand injury ! wear protective gloves while handling the blades. 1 5 3 4 2 6 11 8 10 7 9 12 fig. 9 blade replacement 5.1 replacement of the upper blade spare part: 8930509.001 circular bl...
Page 13
13 6 licences 6.1 eu declaration of conformity cab produkttechnik gmbh & co kg wilhelm-schickard-str. 14 d-76131 karlsruhe deutschland eu declaration of conformity we declare herewith that the following device as a result of design, construction and the version put in circulation complies with the r...
Page 14
14 14 6.2 fcc note: this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environmen...
Page 15
15 7 index c circular blade ...................................12 connecting .........................................7 contents of delivery ............................7 e earthing ..............................................7 environment .......................................4 error messages .....