Summary of MAESTRO 3E/450
Page 1
Operator's manual maestro 3e pcb separator.
Page 2
2 2 description type pcb separator maestro 3e/450 pcb separator maestro 3e/600 edition: 11/2009 - part no. 9008929 copyright this documentation as well as translation hereof are property of cab produkttechnik gmbh & co. Kg. The replication, conversion, duplication or divulgement of the whole manual ...
Page 3
2 3 table of contents 1 introduction ............................................................................................................................................ 4 1.1 instructions ..........................................................................................................
Page 4
4 4 1.1 instructions important information and instructions in this documentation are designated as follows: danger! Draws your attention to an exceptionally grave, impending danger to your health or life. ! Warning! Indicates a hazardous situation that could lead to injuries or material damage. ! A...
Page 5
4 5 1.4 safety marking 2 1 fig. 1 safety marking 1 hazard by electrical charge ! Provide an earthing connection via press stud. 2 risk of hand injury ! Wear protective gloves while pcb separating. Table 1 safety marking 1.5 environment obsolete devices contain valuable recyclable materials that shou...
Page 6
6 6 for the commercially viable assembly and mounting of printed circuit boards, there is an ever increasing requirement for multiple-use material. The necessity however, to break off sections of the circuit board by hand can cause damage to the delicate circuitry and components. The fibre-glass mat...
Page 7
6 7 3 installation 3.1 unpacking and setting-up the device lift the device out of the box. Check device for damage which may have occurred during transport. Set up device on a level surface. Check delivery for completeness. Contents of delivery: • pcb separator • documentation • allen key 2 mm • opt...
Page 8
8 8 3 installation 3.4 height adjustment of the upper blade i notice! To avoid possible damage on the blades during transport the upper blade (5) is fixed in the "park position" so that there is a maximum distance to the lower blade. Set the upper blade into the working position before starting oper...
Page 9
8 9 3 installation 3.5 adjustment of the stop of the upper blade i notice! The lower stop of the upper blade adjustment is already adjusted by delivery. After a long operation time, while working at strongly varying temperatures or else after replacing a blade, it is recommended to re-adjust the low...
Page 10
10 10 3 installation 3.6 check the blade alignment i notice! When the machine is put into operation for the first time, or following a move of equipment or a change of blades, it is advantageous to re-check the alignment of the blades in relationship to one another. For this purpose a dial gauge ass...
Page 11
10 11 3 installation 3.8 adjustment of table and platform 1 2 1 2 3 1 2 1 2 4 fig. 9 adjustment of table and platform adjust the height of table (3) and platform (4) as follows : 1. Loosen screws (1). 2. Move table (3) or platform (4) in the holes (2). 3. Tighten screws (1). 4 operation ! Warning! R...
Page 12
12 12 5 blade replacement 5.1 replacement blades type circular blade lineal blade part no. Description part no. Description part no. Description 8933945 maestro 3e/450 8930509.001 circular blade 8933394.001 lineal blade 450/370 8935000 maestro 3e/600 8930509.001 circular blade 8933682.001 lineal bla...
Page 13
12 13 5 blade replacement 5.3 replacement of the lower (lineal) blade ! Warning! Risk of hand injury ! Wear protective gloves while handling the blades. 3 5 6 1 2 4 7 10 10 10 10 9 11 7 1 8 6 fig. 12 replacement of the lower blade 1. Move the blade carrier (1) to the end of the lower blade (7) above...
Page 14
14 14 6 index b blade alignment ................................10 c circular blade ...................................12 contents of delivery ............................7 d dial gauge assembly ........................10 e earthing ..............................................7 i important informa...