Cabela's PRECISE CUT 8000 RPM 52-0601 Instruction Book - page 2
-2-
COMPONENT LIST
DIAGRAM
PART
PART NO.
NUMBER DESCRIPTION
NUMBER
1
CuttingBlade(2)
52-0301
2
SpinTesterAssembly(2)
52-0302
3
ShaftPositionBracket
52-0305
4
MeasuringTape
52-0316
5
SocketHeadCapScrew
52-0320
6
PowerCord
N/A
7
On/OffSwitch
N/A
8
DustCollector
52-0331
9
DustCollectorBracket
52-0332
10
ThumbScrew(2)
52-0333
11
Small(1-1/4”(3.2cm))DustCollectorAdaptor 52-0340
12
Large(2-1/4”(5.7cm))DustCollectorAdaptor 52-0341
13
ArrowShaftGuide
52-0306
14
ElectricMotor8000RPM
52-0202
15
RubberFeet
52-0329
16
WrenchKit
52-0330
17
BladeMountingBracketAssembly
52-0314
17aBladeSpacer
17bBladeRetainingNut
ARROW SAW BLADE REPLACEMENT
Your
Arrow Saw comes complete with two, reinforced Cutting Blades.
These
Cutting Blades are ideal for cutting both carbon and aluminum
arrow shafts. To order replacement
Cutting Blades, contact Customer
Service at the telephone number listed on the back of this manual.
1. Set the
On/Off Power Switch to the “OFF”
position. Disconnect the
Power Cord from the
power source.
2. Loosen the two
Thumb Screws holding the
Blade Shield to the Arrow Saw.
Figure 13
3. Remove the
Thumb Screws and Cutting
Blade Shield.
3. Remove the
Socket Head Cap Screw
securing the
Arrow Shaft Guide to the Base.
Figure 14
4. Remove the
Arrow Shaft Guide.
5. Insert the long leg of the largest
Allen
Wrench supplied with your Arrow Saw into
one of the holes in the outer edge of the
Blade
Mounting Bracket.
Figure 15
6. Place the
Wrench onto the Blade Retaining
Nut. While holding the Allen Wrench, loosen
the
Blade Retaining Nut (rotate counter
clockwise) until you can remove it by hand.
7. Remove the
Blade Retaining Nut, Blade
Spacer and Cutting Blade.
8. Carefully install a new
Cutting Blade.
CAUTION: NEVER USE A BROKEN, WORN
OR CRACKED BLADE!
9. Re-install the
Blade Spacer and Blade
Retaining Nut.
10. Re-install the
Arrow Shaft Guide and
Blade Shield. CAUTION: NEVER OPERATE
THE ARROW SAW WITHOUT THE BLADE
SHIELD SECURELY MOUNTED IN PLACE!
The
Arrow Saw Cutting Blade rotates at very high speeds. It is normal for the Arrow
Saw to vibrate during operation. If you experience excessive noise and/or vibration
during operation, or blade breakage, check all parts to ensure they are properly and
securely mounted. If the problem continues, please contact Customer Service.
FIGURE 13
Blade Shield
Thumb Screws
Arrow Shaft
Guide
FIGURE 14
Arrow Shaft
Guide
Socket Head
Cap Screw
Base
Cutting
Blade
FIGURE 15
Allen
Wrench
Cutting
Blade
Base
Blade
Mounting
Bracket
Blade
Retaining
Nut
Blade
Spacer
Wrench
-11-
WARNING!
Before cleaning, assembling or disassembling the Arrow
Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE
OUTLET/POWER SOURCE!
Before beginning the assembly, check the package contents for all of the parts.
If you are missing any parts, or if any parts are damaged, contact
Cabela’s Customer Service- Retail Store Purchases 1-800-905-2731 (U.S. & Canada) /
Catalog & Internet Purchases: 1-800-237-8888 / All International: 1-308-234-5555