Summary of WIS-Q5300
Page 1
5g cpe user manual page 1 , total 25 wis-q5300 user manual v1.0
Page 2: 1. Application
5g cpe user manual page 2 , total 25 1. Application thank you for your purchase wis-q5300 5g cpe wireless ap。this handbook is to help you know and co nfigure wis-q5300. 2. Configuration preparation 2.1 installation device figure 1 press the clip of 5g cpe，pull out the cover，stick one end of cable ...
Page 3
5g cpe user manual page 3 , total 25 figure 2 3. Configuration instruction 3.1 main page after logining enter automatically into main page, as shown. Status has 3 status label pages, wireless、 network and system page. The below is introduced separately..
Page 4
5g cpe user manual page 4 , total 25 figure 3-1 3.1.1 wireless page radio status box mainly shows work mode and rf information of 5g cpe. Wireless mode： working mode of 5g cpe, supporting 4 kinds of working mode, ap mode、 station mode、ap wds mode and station wds mode； radio mode: working mode of rad...
Page 5
5g cpe user manual page 5 , total 25 sending rate. If ap and station can reach to 40mhz channel bandwidth, max sending rate can reach to 300mbps, and throughout rate can improve more than twice. Station status box shows cpe working as station mode. Up/down: up means cpe has successfully connected wi...
Page 6
5g cpe user manual page 6 , total 25 figure 3-2 network mode of network role status box shows current network mode. Network mode: device supports 3 kinds of network modes, namely bridge mode、soho router mode and wisp mode. We will have a brief introduction to those: 1. Bridge mode: bridge mode is ty...
Page 7
5g cpe user manual page 7 , total 25 bridge mac： mac address of bridge interface； gateway： gateway ip address of bridge interface； primary dns ip： primary dns address of bridge interface； secondary dns ip： secondary dns address of bridge interface； 3.1.3 system page this page mainly shows version, d...
Page 8
5g cpe user manual page 8 , total 25 figure 3-4 interface： listing all interfaces and interface name； mac address： listing mac address of all interfaces； tx bytes： sending bytes number； tx packet： sending packet ； tx err： sending error packet ； rx bytes： receiving bytes ； rx packet: receiving packet...
Page 9
5g cpe user manual page 9 , total 25 aid: connecting id of sta； signal： ap detected rssi of sta； assoc time： time online of sta； tx/rx packets： send-receive packets between ap and sta. Tx means sending packets from ap to sta, rx means receiving packets from sta to ap； tx/rx bytes: send-receive bytes...
Page 10
5g cpe user manual page 10 , total 25 3.1.8 routes list routes list shows current routing relationship of device, as figure 3-8. Figure 3-8 destination: destination address and mask; gateway： next address against destination address, that is gateway address. Flags： network type of this routing info;...
Page 11
5g cpe user manual page 11 , total 25 rx bytes: cpe receiving bytes by ppp interface. 3.1.10 dhcp server list dhcp server list shows status of assigning ip address when cpe is dhcp server, as figure 3-10。 figure 3-10 mac address： mac address of dhcp client； ip address： ip address of dhcp client； rem...
Page 12
5g cpe user manual page 12 , total 25 3.2.1 basic wireless settings wireless mode： used for working mode of wlan, 5g cpe supporting ap mode, station mode, ap wds mode and station wds mode, the default is station mode. Because settings of those 4 modes have little impact to parameter setting of whole...
Page 13
5g cpe user manual page 13 , total 25 will trigger aggr limit. 3.3 wireless page wireless page is used for setting wireless service of ap mode or relevant parameters for station mode connecting ap . 3.3.1 ap/ap wds mode when cpe is set as ap/ap wds mode, wireless page is shown as figure 3-12. 1. Wir...
Page 14
5g cpe user manual page 14 , total 25 security： used for setting security type, the default is none.； if choosing wep security type，as shown figure 3-13. Figure 3-13 authentication type： used for setting authentication method, the default is open； wep key length： used for setting wep key length, the...
Page 15
5g cpe user manual page 15 , total 25 figure 3-15 1. Wireless settings ssid: when cpe is set as station mode, enter here ssid of linked ap. If just enter ssid not ap mac address, cpe will choose the strongest signal among homonym ssid to link. Lock to ap mac: used for locking mac address needing to ...
Page 16
5g cpe user manual page 16 , total 25 lock to ap: locking it as wireless service that cpe will connect. 2. Wireless security there is no more introduction for choosing it according to authentication method and encryption way. 3.4 network page network page is used for setting relevant parameters of n...
Page 17
5g cpe user manual page 17 , total 25 network mode: used for setting current network mode. 2. Management network settings bridge ip address: bridge ip address obtaining way, separately static set and dhcp access； ip address: used for setting static ip address； netmask: used for setting netmask of st...
Page 18
5g cpe user manual page 18 , total 25 figure 3-18 1. Network role network mode : used for setting current network mode. 2. Wan network settings wan ip address: wan ip adsress obtaining way, separately static set, dhcp access and pppoe negoiation. Because static set and dhcp access are the same with ...
Page 19
5g cpe user manual page 19 , total 25 mtu/mru: used for setting mtu and mru pppoe negoiation； encryption: used for setting mppe agreement when“enable” or “to enable” pppoe negoiation is using （microsoft point-to-point encryption agreement）； nat： used for setting nat service of “enable” or “to enable...
Page 20
5g cpe user manual page 20 , total 25 figure 3-19 3.5.1 web server server port: used for setting server port of web service, the default is 80； session timeout: used for setting web session timeout, the default is 15 minutes. 3.5.2 telnet server enable telnet server: used for “enable” or “to enable”...
Page 21
5g cpe user manual page 21 , total 25 spoofing attack detect: spoofing attack, if enable, prevent outer net linking by using inner net ip； ping attack detect: ping request, if enable, abandon ping requestof outer net sending； tcp null scan detect： tcp null scan, if enable, abandon null scan of tcp s...
Page 22
5g cpe user manual page 22 , total 25 worm_virus: worm virus, if enable, prevent worm virus attack； shake_virus: shake virus, if enable, prevent shake virus attack； shock_virus: shock virus, if enable, prevent shock virus attack； hackers_horse： hackers horse, if enable, prevent hackers horse attack ...
Page 23
5g cpe user manual page 23 , total 25 figure 3-24 ※attention: mac control is available to all ports. Pls be careful to setup. 3.6 system page sytem page is mainly used for setting relevant device management, as figure 3-25..
Page 24
5g cpe user manual page 24 , total 25 figure 3-25 3.6.1 device device description: used for setting device description； enable startup date: used for setting enable startup date, the default is enable state； startup date: used for setting device startup date. 3.6.2 date settings time zone: used for ...
Page 25
5g cpe user manual page 25 , total 25 3.6.3 system accounts username: used for setting admin username； current password: amending username and new password after entering current password； new password: used for setting new password； verify new password: used for verifying new password. 3.6.4 config...