1. DL manuals
  2. Cabletron Systems
  3. Chassis
  4. 9C114
  5. Installation Manual

Cabletron Systems 9C114 Installation Manual

Manual is about: Cabletron Systems Switch User Manual

Summary of 9C114

  • Page 1

    9031125-03 smartswitch 9000 9c114 and 9c714 chassis installation guide.

  • Page 3: Notice

    I notice notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...

  • Page 4: Fcc Notice

    Notice ii fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...

  • Page 5: Declaration of Conformity

    Iii notice declaration of conformity addendum application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european representative address: ...

  • Page 6

    Notice iv.

  • Page 7: Contents

    V contents chapter 1 installing the 9cx14 chassis the smartswitch 9000 .................................................................................................. 1-1 features ................................................................................................................... 1...

  • Page 8

    Contents vi.

  • Page 9: Chapter 1

    1-1 chapter 1 installing the 9cx14 chassis this document contains information necessary to install the smartswitch 9000 9c114 and 9c714 chassis. It is designed for the initial installation only. For detailed operational information on the various smartswitch 9000 components, refer to the following m...

  • Page 10

    Installing the 9cx14 chassis 1-2 redundant power supply modules the 9c114 and 9c714 support the installation of two power supplies for power supply redundancy and load sharing. If a 9c500 power box is used, up to six power supplies may be installed. 9c300-1 environmental module the 9c300-1 environme...

  • Page 11

    1-3 installing the 9cx14 chassis the descriptions of the seven backplane buses are as follows: system management bus 1 the system management bus 1, abbreviated smb-1, is a management bus devoted solely to transferring management information between the modules in the chassis. It is through the smb-1...

  • Page 12: Getting Help

    Installing the 9cx14 chassis 1-4 the cell transfer matrix (installed in the 9c714 chassis only) the cell transfer matrix provides a time division multiplexed (tdm) based mesh of full duplex, high speed (1.6 gbps) dedicated interconnections capable of carrying standard atm cell traffic. These interco...

  • Page 13: Site Guidelines

    1-5 installing the 9cx14 chassis site guidelines the following guidelines must be followed to select a suitable site for the smartswitch 9000. If not, unsatisfactory network performance may result. The site must have an unrestricted free surface area around the smartswitch 9000 chassis, allowing for...

  • Page 14

    Installing the 9cx14 chassis 1-6 installation order once a suitable site has been chosen, the smartswitch 9000 may be installed. The unit may be free standing or rack mounted. It is recommended that the smartswitch 9000 installation proceed in this order: 1. Mount the chassis to the rack or other se...

  • Page 15

    1-7 installing the 9cx14 chassis rack mounting the chassis the chassis can be mounted in a standard 19-inch equipment rack. If the rack is not secured to the floor, it is recommended that the smartswitch 9000 be installed in the bottom half of the rack. This will prevent the rack from being top heav...

  • Page 16

    Installing the 9cx14 chassis 1-8 installing a power supply at least one power supply must be installed on the rear of the mmac-plus chassis. Additional power supplies can be added to achieve redundancy. A power supply is installed by plugging it into either the left or right power supply connector o...

  • Page 17

    1-9 installing the 9cx14 chassis figure 1-3. Installing a power supply 100-125v-12a 200-250v-6a 50-60 hz power supply module 9c214-1 100% 50% 0% status p w r s n b load securing screw tab securing screw slot on chassis.

  • Page 18

    Installing the 9cx14 chassis 1-10 attaching the electrostatic discharge (esd) wrist strap the esd wrist strap must be attached before handling the environmental module or smartswitch 9000 interface modules. In addition, observe all precautions when handling these modules to prevent damage from esd. ...

  • Page 19

    1-11 installing the 9cx14 chassis installing the environmental module the environmental module is installed in the slot above the module card cage in the front of the smartswitch 9000 chassis, as shown in figure 1-5, by following the steps below: 1. Unpack the environmental module by carefully remov...

  • Page 20

    Installing the 9cx14 chassis 1-12 figure 1-5. Installing the environmental module installing smartswitch 9000 interface modules smartswitch 9000 interface modules can be installed in any of the 14 slots that are available. To install interface modules, follow the steps below: 1. Remove the blank pan...

  • Page 21

    1-13 installing the 9cx14 chassis 5. Install the interface module in the chassis by sliding it in any available slot and locking down the top and bottom plastic tabs, as shown in figure 1-6. Take care that the interface module slides in straight and properly engages the backplane connectors. When in...

  • Page 22

    Installing the 9cx14 chassis 1-14 attaching 9c614 inb terminator modules two 9c614 inb terminator modules must be attached to the rear of the smartswitch 9000 chassis when interface modules that use the inb are inserted in the front of the chassis. These modules provide proper termination for the in...

  • Page 23

    1-15 installing the 9cx14 chassis figure 1-7. Attaching the inb terminator modules powering up the smartswitch 9000 the smartswitch 9000 chassis is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the lower right ...

  • Page 24: Operating Specifications

    Installing the 9cx14 chassis 1-16 5. Check that all leds on the inb terminator module are green. If the leds are any color other than green, refer to the inb terminator module installation guide . 6. Check that the status and alarm leds on the environmental module are green. If the leds are not gree...

  • Page 25

    1-17 installing the 9cx14 chassis weight unit: 19.96 kilograms (44 pounds) shipping: 24.95 kilograms (55 pounds) 9c714 mmac-plus chassis dimensions 76.2 h x 48.3 w x 49.3 d centimeters (30 h x 19 w x 19.4 d inches) weight unit: 19.96 kilograms (44 pounds) shipping: 24.95 kilograms (55 pounds) 9c300-...

  • Page 26

    Installing the 9cx14 chassis 1-18 9c614 inb terminator module dimensions 21.59 h x 2.22 w x 14.92 d centimeters (8.5 h x 0.875 w x 5.875 d inches) weight unit: 0.45 kilograms (1 pound) shipping: 0.68 kilograms (1.5 pounds).