9032529-01 smartswitch 9000 9c214-3 ac power supply installation guide.
I notice notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...
Notice ii fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...
Iii notice declaration of conformity addendum application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european representative address: ...
Notice iv.
V contents chapter 1 introduction using this manual........................................................................................................ 1-1 the 9c214-3 power supply.......................................................................................... 1-1 features ...............
Contents vi.
1-1 chapter 1 introduction using this manual read through this manual to become familiar with its contents and to gain an understanding of the features and capabilities of the 9c214-3 power supply prior to installing and operating it. Chapter 1, introduction , provides a brief description of the 9c2...
Introduction 1-2 figure 1-1. The 9c214-3 power supply 207-264v-12a 50-60 hz 9c214-3 100% 50% 0% load power supply module status p w r s n b status led power supply smb status led power supply level indicator led power switch ac power socket.
1-3 introduction features diagnostic controller for management each 9c214-3 power supply has a diagnostic controller which includes a microprocessor that monitors the numerous power supply functions available to the network manager via lcd, as well as local and remote management. Internal temperatur...
Introduction 1-4 power distribution system the smartswitch 9000 uses a distributed dc power distribution system (figure 1-2) similar to those used in super computers. Three separate power buses are used to distribute dc power. The 48-volt dc system power bus, located on the backplane, powers all mod...
1-5 introduction getting help for additional support related to this device or document, contact cabletron systems using one of the following methods: before calling cabletron systems, have the following information ready: • your cabletron systems service contract number • a description of the failu...
Introduction 1-6.
2-1 chapter 2 installing the 9c214-3 power supply at least one power supply must be installed on the rear of the smartswitch 9000 chassis. Additional power supplies can be added to achieve redundancy. A power supply is installed by plugging it into either the left or right power supply connector on ...
Installing the 9c214-3 power supply 2-2 3. Hold the power supply by the handles on the top and bottom of the unit and do the following: a. Align the power supply so that the lip on the bottom and the hook on the top are slightly above the corresponding slots on the chassis. B. Ease the power supply ...
2-3 installing the 9c214-3 power supply powering up the 9c214-3 power supply the 9c214-3 power supply is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the lower right front corner of the power supply. 2. Plug t...
Installing the 9c214-3 power supply 2-4.
3-1 chapter 3 9c214-3 power supply operation the 9c214-3 power supply can operate with input voltages ranging from 207–264 vac at 50/60 hz. Each 9c214-3 provides a maximum of 2000 watts of power to the smartswitch 9000. When two power supplies are installed, the system uses a current sharing scheme ...
9c214-3 power supply operation 3-2 system diagnostic controller the system diagnostic controller is composed of a z-80 microprocessor and its supporting logic. The system diagnostic controller monitors the power supply’s input and output power parameters as well as the temperature and fan status. In...
3-3 9c214-3 power supply operation pwr status led the pwr status led indicates the status of a power supply’s input and output. The possible states and descriptions of the pwr status led are listed in table 3-1. Smb status led the smb status led indicates the status of the diagnostic controller. The...
9c214-3 power supply operation 3-4 power supply level indicator led the power supply level indicator led indicates the percentage of the power supply load. The possible states and descriptions of the power supply level indicator led are listed in table 3-3. Table 3-3. Power supply level indicator le...
4-1 chapter 4 specifications safety the 9c214-3 power supply, when properly installed on the smartswitch 9000 chassis, complies with the following safety specifications and standards: • ul 1950 • csa c22.2 no. 950 • en 60950 • iec 950 • emi requirements of fcc part 15 class a • en 55022 class a • vc...
Specifications 4-2 physical dimensions 60.96 h x 19.05 w x 13.97 d centimeters (24 h x 7.5 w x 5.5 d inches) weight unit: 8.6 kilograms (19 lbs.) shipping: 9.9 kilograms (22 lbs.) environmental operating temperature: 5–40° c, 51–104° f operating humidity: 5% to 95% cooling: 2.15 cubic meters (76 cub...
4-3 specifications output voltage each 9c214-3 power supply is capable of generating the following output voltages: 56.0 volts @35a 3.3 volts @17a 5.1 volts @18a.
Specifications 4-4.