Epim-3ps installation guide cabletron systems, p.O. Box 5005, rochester, nh 03866-5005 p/n 9031283-01 epim-3ps book page 1 tuesday, august 18, 1998 8:42 am.
Epim-3ps book page 2 tuesday, august 18, 1998 8:42 am.
Notice i notice cabletron systems reserves the right to make changes in specifications and other infor- mation contained in this document without prior notice. The reader should in all cases con- sult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or ...
Notice ii note: this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. T...
Notice iii by utilizing the enclosed product, you are agreeing to become bound by the terms of this agreement, which includes the license and the limitation of warranty and disclaimer of liability. If you do not agree to the terms of this agreement, promptly return the un- used product to the place ...
Notice iv 2. No liability for consequential damages. In no event shall cabletron or its suppliers be liable for any damages whatsoev- er (including, without limitation, damages for loss of business, profits, business interruption, loss of business information, special, incidental, consequential, or ...
Introduction page 1 introduction welcome to the epim-3ps installation guide. This manual guides you through the installation and setup of the epim-3ps and includes the following sections: • brim installation considerations • installing the epim-3ps • making connections • epim-3ps leds brim installat...
Brim installation considerations page 2 table 1. Epim-3ps/brim configuration you must match the brim slot with the correct epim slot. Refer to your brim documentation for specific brim and epim installation procedures. Note : on some devices, the epim slot is located under the brim slot. In these ca...
Installing the epim-3ps page 3 installing the epim-3ps to install the epim-3ps into a media interface module (mim): 1.) remove the mounting screw shown in figure 1. Note : when removing an epim, be sure to pull the module straight out to prevent damage to the connector. 2.) remove the coverplate or ...
Installing the epim-3ps page 4 figure 1. Epim-3ps installation emm-e6 ethernet stby rcv xmt cln d c b a cpu reset sn e pi m 1 e pi m 2 c o m 1 c o m 2 f e lan pwr sys reset s1 s0 console s1 s0 epim-3ps book page 4 tuesday, august 18, 1998 8:42 am.
Connecting the epim-3ps to a brim page 5 connecting the epim-3ps to a brim to connect an epim-3ps to a brim: 1.) plug one end of the ethernet cable (p/n 9372088) into the epim-3ps (figure 2). 2.) plug the other end of the cable into the brim. 3.) after returning the mim to the mmac, returning power ...
Connecting the epim-3ps to a brim page 6 figure 2. Connecting a brim to the epim-3ps epim-3ps brim ethernet cable epim-3ps book page 6 tuesday, august 18, 1998 8:42 am.
Epim led page 7 epim led the epim-3ps has one amber led that indicates a connection exists between the brim and epim-3ps. Figure 3. Epim-3ps led connection led epim-3ps book page 7 tuesday, august 18, 1998 8:42 am.
Getting help page 8 getting help if you have questions, or need additional help, contact cabletron systems technical support: by phone (603) 332-9400 monday-friday; 8am-8pm est by compuserve ® go ctron from any ! Prompt by internet mail support@ctron.Com epim-3ps book page 8 tuesday, august 18, 1998...
