Hsim-g01/g09 user’s guide hsim-g lnk sx 9032398-04.
Hsim-g01/g09 user’s guide i notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware...
Notice ii hsim-g01/g09 user’s guide industry canada notice this digital apparatus does not exceed the class a limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the canadian department of communications. Le présent appareil numérique n’émet pas d...
Notice hsim-g01/g09 user’s guide iii cabletron software program license 1. License. You have the right to use only the one (1) copy of the program provided in this package subject to the terms and conditions of this license agreement. You may not copy, reproduce or transmit any part of the program e...
Notice iv hsim-g01/g09 user’s guide safety information class 1 laser transceivers the hsim-g01/g09 gigabit ethernet modules use class 1 laser transceivers. Read the following safety information before installing or operating these adapters. The class 1 laser transceivers use an optical feedback loop...
Notice hsim-g01/g09 user’s guide v declaration of conformity application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european represent...
Notice vi hsim-g01/g09 user’s guide.
Hsim-g01/g09 user’s guide vii contents chapter 1 introduction 1.1 using this manual....................................................................... 1-2 1.2 document conventions ............................................................... 1-2 1.3 getting help...................................
Contents viii hsim-g01/g09 user’s guide.
Hsim-g01/g09 user’s guide 1-1 chapter 1 introduction welcome to the cabletron systems hsim-g01/g09 user’s guide . This manual describes the hsim-g01 and hsim-g09 and provides information concerning features, installation, troubleshooting, the use of local management, and specifications. A general wo...
Chapter 1: introduction 1-2 hsim-g01/g09 user’s guide 1.1 using this manual read through this manual completely to familiarize yourself with its content and to gain an understanding of the features and capabilities of the hsim-g. The following list provides an overview of each section of this manual...
Getting help hsim-g01/g09 user’s guide 1-3 1.3 getting help for additional support related to this device or document, contact cabletron systems using one of the following methods: before calling cabletron systems, have the following information ready: • your cabletron systems service contract numbe...
Chapter 1: introduction 1-4 hsim-g01/g09 user’s guide 1.4 overview the hsim-g extends the functionality of certain cabletron systems interface modules or standalone devices by providing high-speed uplink capability through gigabit ethernet technology. Section 1.4.1 and section 1.4.2 give information...
Hsim-g01/g09 user’s guide 2-1 chapter 2 installation to install the hsim-g you need the following items: • antistatic wrist strap • phillips screwdriver 2.1 unpacking the hsim-g unpack the hsim-g as follows: 1. Remove the shipping box material covering the hsim-g. 2. Carefully remove the module from...
Chapter 2: installation 2-2 hsim-g01/g09 user’s guide 2.2 installing an hsim-g you can install an hsim-g in any cabletron systems device that supports hsim technology (e.G., 2e42-27, 6e132-25). The following sections provide instructions for installing an hsim-g in an interface module or in a standa...
Installing an hsim-g hsim-g01/g09 user’s guide 2-3 figure 2-1 removing the hsim coverplate 7. Refer to figure 2-2 and place the hsim-g behind the module faceplate. 8. Align the hsim connector of the hsim-g with the hsim pins on the module. 9. Press down firmly on the back of the hsim-g until the con...
Chapter 2: installation 2-4 hsim-g01/g09 user’s guide 10. Secure the hsim-g to the module faceplate using the mounting screws saved in step 5. 11. Secure the hsim-g to the module standoffs using the standoff screws saved in step 6. 12. Reinstall the interface module in the chassis. 13. Reattach the ...
Installing an hsim-g hsim-g01/g09 user’s guide 2-5 2.2.2 installing an hsim-g in a standalone device to install an hsim-g into a standalone device (e.G., 2e42-27), perform the following steps: 1. Power down the device and remove the power cord. 2. Disconnect any cables connected to the network ports...
Chapter 2: installation 2-6 hsim-g01/g09 user’s guide 11. Secure the hsim-g to the module standoffs using the standoff screws saved in step 6. 12. Reattach the chassis cover to the standalone device, reconnect the power cord, and reconnect the standalone device to the network. 2.3 connecting to the ...
Connecting to the network hsim-g01/g09 user’s guide 2-7 2.3.1 hsim-g network connection to connect the hsim-g01 using multimode and single mode fiber, and the hsim-g09 using single mode fiber to the network, perform the following steps: 1. Remove the protective fiber port covers from the fiber optic...
Chapter 2: installation 2-8 hsim-g01/g09 user’s guide figure 2-4 fiber connections 3. At the other end of the fiber optic cable, attach the sc connector to the other device. 4. Verify that a link exists by checking that the link (lnk) led is on (solid green), the port receive (rx) led is on (flashin...
Connecting to the network hsim-g01/g09 user’s guide 2-9 to remove the sc connector, from the hsim-g, carefully pull the connector out of the port. It may need to be wiggled gently to release the latching keys. If a link has not been established, refer to chapter 3 before contacting cabletron systems...
Chapter 2: installation 2-10 hsim-g01/g09 user’s guide.
Hsim-g01/g09 user’s guide 3-1 chapter 3 lanview leds this chapter describes how to use the lanview leds to monitor the status of the hsim-g and diagnose problems. Figure 3-1 shows the location of the hsim-g leds. Figure 3-1 hsim-g lanview leds transmit (tx) receive (rx) link (lnk) 2398_leds hsim-g l...
Chapter 3: 3-2 hsim-g01/g09 user’s guide table 3-1 hsim-g leds note the terms flashing, blinking, and solid used in table 3-1 indicate the following: flashing indicatesan irregular led pulse. Blinking indicatesa steady led pulse. (approximately 50% on, 50% off) solid indicatesa steady led light. No ...
Hsim-g01/g09 user’s guide 4-1 chapter 4 local management this chapter provides information on the hsim-g screens accessible via the local management of the host platform. One local management screen is specific to the hsim-g, which is detailed in this chapter. All other screens are detailed in the l...
Chapter 4: local management 4-2 hsim-g01/g09 user’s guide figure 4-1 typical hierarchy of local management screens 4.2 gigabit ethernet configuration screen the gigabit ethernet configuration screen allows the user to support the hsim-g01 and the hsim-g09. The screen (see figure 4-2 ) displays the t...
Gigabit ethernet configuration screen hsim-g01/g09 user’s guide 4-3 figure 4-2 gigabit ethernet configuration screen the following defines each field of the gigabit ethernet configuration screen. Port x (read-only) the port or interface number on the host platform in which the hsim-g is installed. P...
Chapter 4: local management 4-4 hsim-g01/g09 user’s guide current oper. Mode (read-only) displays the current operating mode of the port. Regardless of whether an hsim-g01 or hsim-g09 is installed, this field displays 1000base-xfd. Desired oper. Mode (toggle) allows the user to select the desired op...
Gigabit ethernet configuration screen hsim-g01/g09 user’s guide 4-5 4.2.1.1 setting the operational mode use the desired oper. Mode field to set the active technology. This field steps between auto-negotiation and 1000base-xfd. If auto-negotiation is selected, the hsim-g automatically sets the activ...
Chapter 4: local management 4-6 hsim-g01/g09 user’s guide.
Hsim-g01/g09 user’s guide a-1 appendix a specifications this appendix lists the specifications and regulatory requirements for the hsim-g01 and hsim-g09. Cabletron systems reserves the right to change these specifications at any time without notice. The hsim-g01 and hsim-g09 are both fiber optic dev...
Appendix a: specifications a-2 hsim-g01/g09 user’s guide a.1.2 hsim-g09 specifications (1000base-lx) table a-4 gpim-09 operating range a. In order to obtain the distance of 550 m for the gpim-09 using multimode fiber, launch mode conditioning cable must be used. Refer to section 2.3.2 for details. T...
Physical properties hsim-g01/g09 user’s guide a-3 a.2 physical properties a.3 environmental requirements a.4 regulatory compliance this equipment meets the following safety and electromagnetic compatibility (emc) requirements: dimensions 3.18h x 16.51w x 29.21d (cm) 1.25h x 6.5w x 11.5d (in) weight ...
Appendix a: specifications a-4 hsim-g01/g09 user’s guide.