- DL manuals
- Cabletron Systems
- Network Hardware
- KBU64 Rackmount
- User Manual
Cabletron Systems KBU64 Rackmount User Manual
Summary of KBU64 Rackmount
Page 1
Kbu64 rackmount user manual fivemere ltd. Cabletron systems ltd. Fivemere house network house 161 high street newbury business park aldershot london road, newbury hampshire, england berkshire, england gu11 1tt rg13 2pz telephone: [44] (0)1635 580000 fax: [44] (0)1635 44578.
Page 2
Kbu64 rackmount user manual 80-10100001-09 ii publication — 80-10100001-09 publication notice: this manual has been compiled and checked for accuracy. However the information contained in this manual does not constitute a warranty of performance. Cabletron systems ltd. Reserves the right to revise t...
Page 3
Kbu64 rackmount user manual 80-10100001-09 iii history sheet 80-10100001-09 issued separately for the r/m due to usa requirements 21 january 1998.
Page 4
Kbu64 rackmount user manual 80-10100001-09 iv table of contents 1 kbu 64 rackmount specification 1–1 1.1 i ntroduction 1–1 2 front and rear panels and interfaces 2–1 2.1 f ront p anel 2–1 2.2 r ear i nterface c ards 2–1 2.2.1 l ink s ettings 2–3 2.2.2 c ommand p ort - kbu 64 r ear i nterface c ards ...
Page 5
Kbu 64 rackmount specification 80-10100001-09 1–1 1 kbu 64 rackmount specification 1.1 introduction this manual describes the rackmount version of the kbu64. The standalone kbu 64 has its own manual, publication 80-10100000. For information on the command menus and parameters in the rackmount versio...
Page 6
Kbu64 rackmount user manual 80-10100001-09 1–2 fivemere fivemere figure 1.1 the kbu 64 rackmount version up to 13 kbu 64 card pairs may be fitted with either one or two power supplies for resilience. The 1st card slot is for the manager card which controls all cards within the rack via the kbu 64 po...
Page 7
Kbu 64 rackmount specification 80-10100001-09 1–3 the rackmount version of the kbu 64 is functionally the same as the standalone in most respects, as it uses the same software. Therefore most of the sections of your kbu64 manual manual (publication 80- 10100000) relating to kbu 64's operation are re...
Page 8
Front and rear panels and interfaces 80-10100001-09 2–1 2 front and rear panels and interfaces 2.1 front panel see the kbu64 standalone manual (publication 80-10100000) for the description of operation. 2.2 rear interface cards with all 3 card types the user ports are configured as physical dces, th...
Page 9
Kbu64 rackmount user manual 80-10100001-09 2–2 t 1 0 3 r 1 0 4 c 1 0 8 i 1 0 7 s 1 1 4 1 1 5 1 0 5 1 0 9 b a c k u p u s e r 1 f r o n t r e a r ( x . 2 1 ) r e a r ( v . 3 5 ) u s e r 2 t 1 0 3 r 1 0 4 c 1 0 8 i 1 0 7 s 1 1 4 1 1 5 1 0 5 1 0 9 b a c k u p b 1 i n u s e b 1 b a c k u p b 2 i n u s e...
Page 10
Front and rear panels and interfaces 80-10100001-09 2–3 2.2.1 link settings for all 3 types of rear interface card the command port jumper settings are as follows: without manager card with manager card link normal polled polled only jp8 in in x jp9 out out x jp10 out in x jp11 in out x jp12 in in o...
Page 11
Kbu64 rackmount user manual 80-10100001-09 2–4 2.2.2 command port - kbu 64 rear interface cards the command port on each of the rear interface card types is a female 15 way 'd' type and uses the same v28 level circuits as the standalone kbu 64. You can only use this command port when a manager card ...
Page 12
Front and rear panels and interfaces 80-10100001-09 2–5 2.2.3 v35 rear interface card the user and link connectors are both 34 way female mrac. The pin assignments are as follows: pin no. Circuit no. Signal name assuming configured as dte a 101 chassis earth common return b 102 signal ground/chassis...
Page 13
Kbu64 rackmount user manual 80-10100001-09 2–6 2.2.4 x21 rear interface card the user and link connectors are both 15 way 'd'. The pin assignments are as follows: pin no. Circuit no. Signal name assuming configured as dte 1 ground chassis earth common return 8 g signal ground/chassis earth common re...
Page 14
Manager card 80-10100001-09 3–1 3 manager card 3.1 introduction the kbu 64 manager card is a discrete card for use with only rackmount kbu 64 cards. Like the rackmount kbu 64, the manager card also consists of a card pair. The rear card provides a command port for management of all kbu 64 cards with...
Page 15
Kbu64 rackmount user manual 80-10100001-09 3–2 f ro n t r x d t x d r e a r c o m m a n d 1 o f f 2 o f f 3 o f f 4 o f f 5 o f f 6 o f f 7 o f f 8 o f f 9 o f f 1 0 o f f 1 2 o f f 1 3 o f f 1 1 o f f p w r 1 p w r 2 figure 3.1 front and rear panels of the manager card.
Page 16
Manager card 80-10100001-09 3–3 3.2 front panel the front panel of the manager card has the following controls and indicators: • transmit and receive data led’s for the command terminal data lines. These led’s display data activity on both the transmit and receive data circuits. • ac power indicatio...
Page 17
Kbu64 rackmount user manual 80-10100001-09 3–4 the pin assignments are as follows: pin no. Circuit no. Signal name 1 101 chassis earth 2 103 transmit data 3 104 receive data 4 105 request to send 5 106 clear to send 6 107 data set ready 7 102 signal ground/chassis earth 8 109 data carrier detect 15 ...
Page 18
Card installation 80-10100001-09 4–1 4 card installation each kbu 64 ‘front’ card must be associated with an appropriate (v.24, x.21, or v.35) rear interface card i.E. They should always be installed in pairs (although no damage will result in partial installation) if the kbu 64s are to be managed i...
Page 19
Kbu64 rackmount user manual 80-10100001-09 4–2 4.2 configuration using a manager card with the manager card pair and all kbu card pairs fitted the first task is to set the individual kbu 64 poll numbers. Once all the units are installed and a suitable terminal connected to the rack manager card comm...
Page 20
Installation and power supply requirements 80-10100001-09 5–1 5 installation and power supply requirements safety warning: before connecting the mains supply to the unit check the supply voltage as detailed below. The product is a high density rack mounted unit designed to sit in a 19" communication...
Page 21
Kbu64 rackmount user manual 80-10100001-09 5–2 should be removed and the cable re-wired to the correct type of plug. The use of adaptors is not recommended. The wires in the supply cord are coloured in accordance with the following code:- green and yellow earth blue neutral brown live as these colou...
Page 22
Installation and power supply requirements 80-10100001-09 5–3 20mm x 5mm, 3.15ah,250v anti-surge (t) type for 110v to 120v ratings. If any problems are encountered with fuses continually blowing the following alternative ratings maybe used: 20mm x 5mm, 3.15ah,250v anti-surge (t) type for 220v to 240...
Page 23
Rack specifications 80-10100001-09 6–1 6 rack specifications dimensions 482mm w; 400mm h (9u); 370mm d mains voltage 93-132v (110-120v nominal) 187-264v (220-240v nominal) consumption 200va max. Frequency 50/60hz nominal mains rear panel fuses 1.6 or 3.15ah, 250v anti-surge (t) 20x5mm (220-240v rang...
Page 24
Kbu64 rackmount user manual 80-10100001-09 6–2 environment ambient temperature: operating 0 ° c to 30 ° c storage -20 ° c to 70 ° c atmospheric pressure: 86.0kpa to 106.0kpa relative humidity: 5% to 95% non-condensing.
Page 25
Regulatory requirements 80-10100001-09 7–1 7 regulatory requirements 7.1 united kingdom and europe users based in the united kingdom and europe must pay particular attention to the information contained in sections 7.1 and 7.2 . B.A.B.T. Pan european approval number aa6046512. 1. The kbu 64 rackmoun...
Page 26
Kbu64 rackmount user manual 80-10100001-09 7–2 3. The kbu 64 rackmount is approved for direct connection to the x.21 and x.21 bis (v.35) or x.21 bis (v.28) kilostream provided by british telecom plc or any similar service provided by other british telecommunications operators, or a relevant branch s...