Mmac-plus ™ 9w111-08 eight port wan router user’s guide.
I notice notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...
Ii notice fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...
Iii notice doc notice this digital apparatus does not exceed the class a limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the canadian department of communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant l...
Iv notice.
V contents chapter 1 introduction features........................................................................................................................... 1-1 related manuals............................................................................................................ 1-4 ge...
Contents vi.
1-1 chapter 1 introduction the 9w111-08 wan router module, shown in figure 1-1, is a eight port wide area net router. Up to eight front panel network connections can be made to this module and they can be routed to any other port and to any other mmac-plus module via the fnb bus. Features processor ...
Introduction 1-2 management information base (mib) support all concentrator modules provide mib support including the following: • ietf fddi mib • ietf mib ii lanview leds the 9w111-08 uses lanview: the cabletron systems built-in visual diagnostic and status monitoring system. With lanview leds, you...
1-3 features figure 1-1. The 9w111-08 module wan 3 2 1 0 fnb smb cpu 7 6 5 4 a u x c o m s 3 s 2 s 1 s 0 s 7 s 6 s 5 s 4 9w111-08 mmac plus.
Introduction 1-4 related manuals the manuals listed below should be used to supplement the procedures and technical data contained in this manual. Mmac-plus installation guide mmac-plus operations guide mmac-plus 9c300-1 environmental module user’s guide mmac-plus 9c214-1 ac power supply user’s guid...
2-1 chapter 2 installing the mmac-plus module the mmac-plus module may be installed into any of the 14 slots that are available. To install, follow the steps below: 1. Remove the blank panel, covering the slot that the module is being mounted in. All other slots must be covered, if modules are not b...
Installing the mmac-plus module 2-2 figure 2-1. Installing the mmac-plus module 7 flnk 8 flnk flnk 10 flnk ins 11 flnk ins 12 rx tx rx tx rx circuit card card guides metal back-panel jack for esd wrist strap plastic tabs warning: ensure that the circuit card is between the card guides. Lock down the...
2-3 the reset switch the reset switch the reset switch is located on the front panel, under the top plastic tab, as shown in figure 2-2. It serves two functions: • pressing the reset switch twice within three seconds causes the processor to reset. • pressing and holding the switch on for three or mo...
Installing the mmac-plus module 2-4 setting the fnb switch the 9w111-08 module can attach to ether fnb-1 or fnb-2. Figure 2-3 shows the location of the fnb switch, sw201. When this switch is up (toward the top of the module) the 9w111-08 attaches to fnb-2. When down, it attaches to fnb-1. Figure 2-3...
2-5 local management console table 2-1. Terminal setup requirements menu function selection display columns 80 columns setup: controls interpret controls auto wrap no auto wrap text cursor cursor general mode 7 bit control setup: cursor keys normal cursor keys communications setup: transmit transmit...
Installing the mmac-plus module 2-6 an rj-45 connector provides a com interface to the management terminal. Figure 2-4 shows the pinouts. Figure 2-4. Console cable pinouts connect the console to the module as follows: 1. Attach the male rj-45 connector to the com port of the 9w111-08. 2. Attach the ...
3-1 chapter 3 operation the 9w111-08 wan router module is a eight port wide area net router. Up to eight front panel network connections can be made to this module and they can be routed to any other port and to any other mmac-plus module via the fnb bus. Figure 3-1. 9w111-08 block diagram cpu wan p...
Operation 3-2 flexible network bus (fnb) the fnb consists of two dual fddi networks, the fnb-1 and fnb-2, providing up to 400 mbps of data bandwidth. These fddi networks are 100% ansi fddi- compliant, supporting smt (version 7.3), mac, phy, and pmd standards. This allows the fnb to traverse multiple...
3-3 fnb interface fnb interface mmac-plus modules are designed with one of two attachment policies. One allows dual attachment of a module to either fnb-1 or fnb-2; the second allows dual attachment to both fnb-1 and fnb-2. The 9w111-08 has one dual attachment to the fnb backplane, connecting to eit...
Operation 3-4.
4-1 chapter 4 lanview leds the front panel lanview leds, shown in figure 4-1, indicate the status of the module and may be used as an aid in troubleshooting. Figure 4-1. Lanview leds wan 3 2 1 0 fnb smb cpu 7 6 5 4 a u x c o m 9w111-08 system status fnb transmit fnb receive wan status wan activity.
Lanview leds 4-2 the functions of the system management bus (smb) and cpu leds are listed in table 4-1. * at least one wan port in both groups 0-3 and 4-7 are down. The function of the fnb receive led is listed in table 4-2. The function of the fnb transmit led is listed in table 4-3. Table 4-1. Smb...
4-3 lanview leds the functions of the wan status leds are listed in table 4-4. The function of the wan activity leds are listed in table 4-5. Table 4-4. Wan status leds led color state green connection, transmit clock active, receive clock active, no loop mode detected yellow connection, transmit cl...
Lanview leds 4-4.
5-1 chapter 5 specifications safety this equipment meets the following safety requirements: • ul 1950 • csa c22.2 no. 950 • en 60950 • iec 950 • emi requirements of fcc part 15 class a • en 55022 class a • vcci class i • emc the following requirements: en 50082-1 iec 801-2 esd iec 801-3 radiated sus...
Specifications 5-2 physical dimensions 35.0 d x 44.0 h x 3.0 w centimeters (13.8 d x 17.4 h x 1.2 w inches) weight unit: 1.36 kg. (3 lb) shipping: 1.81 kg. (4 lb) environment operating temperature 5 to 40 ° c storage temperature -30 to 90 ° c relative humidity 5% to 95% non-condensing.