1. DL manuals
  2. Cabletron Systems
  3. Switch
  4. SmartSwitch 2500
  5. Reference Manual

Cabletron Systems SmartSwitch 2500 Reference Manual

Other manuals for SmartSwitch 2500: User Manual
Manual is about: Enterasys SmartSwitch 2500: Reference Guide

Summary of SmartSwitch 2500

  • Page 1

    Smartswitch atm switch reference manual 35 industrial way rochester, nh 03866 usa (603) 332-9400 part number 04-0054-01 rev. A order number 9033003.

  • Page 2

    Ii smartswitch atm switch reference manual notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been mad...

  • Page 3

    Smartswitch atm switch reference manual iii fcc class a notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interferen...

  • Page 4

    Iv smartswitch atm switch reference manual declaration of conformity addendum application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way p. O. Box 5005 rochester, nh 03866 product name: smartswitch 2500 family and ...

  • Page 5

    Smartswitch atm switch reference manual v safety information class 1 laser transceivers the iom-29-4, iom-29-4-ir, iom-29-4-lr, iom-39-1 and iom-39-1-lr connectors use class 1 laser transceivers. Read the following safety information before installing or operating one of these modules. The class 1 l...

  • Page 6

    Vi smartswitch atm switch reference manual fiber optic protective caps warning .Read before removing fiber optic protective caps. Cable assemblies and mmf/smf ports are shipped with protective caps to prevent contamination. To avoid contamination, replace port caps on all fiber optic devices when no...

  • Page 7

    Smartswitch atm switch reference manual vii regulatory compliance summary safety the smartswitch 2500 family and smartswitch 6500 meets the safety requirements of ul 1950, csa c22.2 no. 950, en 60950, iec 950, and 73/23/eec. Emc the smartswitch 2500 family and smartswitch 6500 meets the emc requirem...

  • Page 8

    Viii smartswitch atm switch reference manual revision history document name: smartswitch atm switch reference manual document part number: 04-0054-01 rev. A document order number: 9033003 author: robert de peyster editor: ayesha maqsood illustrator: mike fornalski date revision description "«Àˆ•Ê£™™...

  • Page 9

    Smartswitch atm switch reference manual ix table of contents table of contents 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 audience and scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 10

    X smartswitch atm switch reference manual table of contents clientvc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54 community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 11

    Smartswitch atm switch reference manual xi table of contents lesarp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-130 lesclient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 12

    Xii smartswitch atm switch reference manual table of contents portmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-227 portstat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 13

    Smartswitch atm switch reference manual xiii table of contents switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-325 switchconfig. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 14

    Xiv smartswitch atm switch reference manual list of tables list of tables table 1-1 list of operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 table 2-1 oc-12/stm-4 port loopback modes . . . . . . . . . . ...

  • Page 15

    Smartswitch atm switch reference manual 1-1 1 introduction this reference manual describes the console commands for the smartswitch 2500 family and the smartswitch 6500. Unless otherwise noted, the information in this manual applies to both the smartswitch 2500 family and smartswitch 6500. Audience ...

  • Page 16

    1-2 smartswitch atm switch reference manual additional information introduction additional information you will find a list of acronyms, details about technical support, and an index at the back of this manual. The index contains page references for all switch attribute sections, command parameters,...

  • Page 17

    Smartswitch atm switch reference manual 1-3 introduction abbreviations abbreviations pay attention to how switch attributes appear in section headings of chapter 2. Switch attributes are not case sensitive, but you must spell them correctly. For example, if the heading states busstat, you must enter...

  • Page 18

    1-4 smartswitch atm switch reference manual help options introduction help options the console provides several levels of help for console commands. For example, to list the switch attributes that can be used with a particular operator, enter the word help (or ? ) followed by the operator. Switch_pr...

  • Page 19

    Smartswitch atm switch reference manual 1-5 introduction switch attribute entries switch attribute entries each switch attribute has an entry in chapter 2. The entry starts with the attribute name and a brief explanation of the attribute’s purpose. Note a few switch attributes apply to the smartswit...

  • Page 20

    1-6 smartswitch atm switch reference manual switch attribute entries introduction parameters most switch attributes have input or output parameters (or both). If an attribute has parameters, they are listed in tables under a “parameters” heading. You enter input parameters at the console command lin...

  • Page 21

    Smartswitch atm switch reference manual 1-7 introduction switch attribute entries descriptions a “descriptions” section follows parameters. The descriptions section shows command syntax (operator, attribute, and input parameters). It also gives additional information on what the command does and how...

  • Page 22

    1-8 smartswitch atm switch reference manual port numbering introduction port numbering port numbering for the smartswitch 6500 is different from that for the smartswitch 2500 family. For the smartswitch 6500, physical port numbering uses the following format: slot number i/o module letter port numbe...

  • Page 23

    Smartswitch atm switch reference manual 1-9 introduction list of operators and switch attributes delete (remove) modify (set) serviceregistry spvc spvcaddress spvp* trafficdescriptor trapcommunity alarms alias atmfilter atmfilterset atmroute busclient buselan client community elan events ipatmpvc le...

  • Page 24

    1-10 smartswitch atm switch reference manual list of operators and switch attributes introduction show (display) pnninode pnninodetimer pnnipeergroupid pnnipglelection pnniscopemapping portclockmode portconfig portfilterset portmode porttrafficcongestion prompt redundancyinfo redundancyoff* redundan...

  • Page 25

    Smartswitch atm switch reference manual 1-11 introduction list of operators and switch attributes activate/deactivate backup/restore clear mynmaddr netprefix networkclock pnniinterface pnnilink pnnimetrics pnnineighbor pnninetworklink pnninetworknode pnninode pnninodetimer pnnipglelection pnniptse p...

  • Page 26

    1-12 smartswitch atm switch reference manual list of operators and switch attributes introduction disable/enable execute flush restart setup start stop config leserrorlog lecslnnistat lesstat portstats pvc pvp* privilege cpuswitchover* csmswitchover* alias config pvc pvp* client switch lecs les ping...

  • Page 27

    Smartswitch atm switch reference manual 1-13 introduction list of operators and switch attributes update firmware.

  • Page 28

    1-14 smartswitch atm switch reference manual list of operators and switch attributes introduction.

  • Page 29

    Smartswitch atm switch reference manual 2-1 2 console commands note a few switch attributes apply to the smartswitch 6500 only. For those attributes, the following appears below the attribute name: (smartswitch 6500 only). If this notation does not appear, the attribute applies to both the smartswit...

  • Page 30

    2-2 smartswitch atm switch reference manual 622loopback console commands descriptions examples switch_1 # show 622loopback port(all) : port type loopback ============================================================================== 1a1 622 none switch_1 # set 622loopback port() : 1a1 loopback(none)...

  • Page 31

    Smartswitch atm switch reference manual 2-3 console commands alarmdisplay alarmdisplay use alarmdisplay to enable/disable the display of alarm messages at the console. Note use alarms to display the alarms currently logged. Operators modify, show parameters this attribute has no output parameters. D...

  • Page 32

    2-4 smartswitch atm switch reference manual alarms console commands alarms use alarms to display or delete alarms currently logged. Note 2«ÊÍœÊ{äÊ>•>À“ÃÊ>ÀiÊ«iÀÈÃÍi˜ÍÊœ˜ÊÀilœœÍÊ-Ài“>ˆ˜Êˆ˜Ê•œ}®°Ê!œÊiÜi˜ÍÃÊ>ÀiÊ«iÀÈÃÍi˜ÍÊœ˜Ê ÀilœœÍ° operators delete, show parameters this attribute has no output param...

  • Page 33

    Smartswitch atm switch reference manual 2-5 console commands alarms examples switch_prompt # show alarms index(all) : 0 33554652 000:00:32:238 --------------------------------------------------- lecs operational switch_1 # delete alarms index(all) : switch_1 # show alarms index(all) :.

  • Page 34

    2-6 smartswitch atm switch reference manual alias console commands alias use alias to manage aliases for console commands. You can use up to 15 aliases. Note 0…iÊ>•ˆ>ÃÊ ping ʈÃÊ«ÀiÃi˜ÍÊÝ…i˜ÊÍ…iÊÃ݈Ív…ʈÃÊÃ…ˆ««i`ÊvÀœ“ÊÍ…iÊv>vÍœÀßÊ- ping ʈÃÊ>˜Ê>•ˆ>ÃÊ vœÀÊ start ping ®° operators add, delete, flush, ...

  • Page 35

    Smartswitch atm switch reference manual 2-7 console commands alias examples switch_prompt # add alias aliasname() : spnni aliasedstring() : show pnniinterface switch_prompt # switch prompt # delete alias aliasname() : spnni spnni -> show pnniinterface confirm(y/n)?:y switch_prompt # switch_prompt # ...

  • Page 36

    2-8 smartswitch atm switch reference manual alias console commands switch_prompt # show alias aliasname(all) : alias list ============================================================================== index alias name : aliased command 1 ping : start ping 2 sp : show pnninode switch_prompt #.

  • Page 37

    Smartswitch atm switch reference manual 2-9 console commands atmfilter atmfilter use atmfilter to manage atm filters on the switch. Operators add, delete, modify, show parameters in the output parameter table below, ( ) indicates parameters that are available only through the show atmfilter /d (deta...

  • Page 38

    2-10 smartswitch atm switch reference manual atmfilter console commands descriptions [src atm addr] source (calling party) address for which the filter should be applied. [src addr mask] mask of the source atm address. [dst atm addr] destination (called party) address for which the filter should be ...

  • Page 39

    Smartswitch atm switch reference manual 2-11 console commands atmfilter examples switch_prompt # add atmfilter filtername(filter1) : allow_src_pfx src-atmaddr() : 39:20:10:35:00:10 srcaddrmask(ff:ff:ff:ff:ff:ff) : dst-atmaddr() : dstaddrmask(): filtertype() : admit switch_prompt # add atmfilter filt...

  • Page 40

    2-12 smartswitch atm switch reference manual atmfilter console commands switch_prompt # show atmfilter /d filtername(all) : ============================================================================ filter name : allow_src_pfx src atm addr: 39:20:10:35:00:10 src addr mask: ff:ff:ff:ff:ff:ff dst at...

  • Page 41

    Smartswitch atm switch reference manual 2-13 console commands atmfilterset atmfilterset use atmfilterset to manage an atm filter set. An atm filter set consists of one or more atm filters. Each atm filter set is assigned to a pair of ports, having one incoming port and one outgoing port (alternately...

  • Page 42

    2-14 smartswitch atm switch reference manual atmfilterset console commands descriptions (if /d or a specific [filtersetname] is specified, you also get a breakdown of totaladmits, totaldenies, and referencecount for each filter in the set.) operator parameters/permissions description add atmfilterse...

  • Page 43

    Smartswitch atm switch reference manual 2-15 console commands atmfilterset examples switch_prompt # show atmfilter filtername(all) : filtername filtertype totaladmits totaldenies referencecount ============================================================================== filter2 deny 0 0 0 filter3 ...

  • Page 44

    2-16 smartswitch atm switch reference manual atmroute console commands atmroute use atmroute to manage routes to reachable addresses from the switch. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you ...

  • Page 45

    Smartswitch atm switch reference manual 2-17 console commands atmroute note if you hot-swap a tsm with a tsm of a different type (different i/o ports), routing information associated with ports on the original tsm is deleted. Before you insert a replacement tsm, you can display existing routing info...

  • Page 46

    2-18 smartswitch atm switch reference manual atmroute console commands descriptions examples switch_prompt # show atmroute num(all) : num port number atm address type proto ================================================================================ 1 cpu 39:00:00:00:00:00:00:00:00:00:a3:87:0b:0...

  • Page 47

    Smartswitch atm switch reference manual 2-19 console commands atmroute switch_prompt # switch_prompt # add atmroute portnumber() : 7a3 atmaddress() : 20:01:02:03 prefixlength(32) : addressindex(0) : type(internal) : scope(0) : metricstag(0) : advertising(no) : switch_prompt # show atmroute num(all) ...

  • Page 48

    2-20 smartswitch atm switch reference manual busclient console commands busclient use busclient to display or delete lane clients connected to a bus. Each lane client is identified uniquely by its lec id. Operators delete, show parameters descriptions input parameter description value/field size def...

  • Page 49

    Smartswitch atm switch reference manual 2-21 console commands busclient examples switch_prompt # delete busclient elannumber(0) : lecid(0) : 14 atmaddress : 39:00:00:00:00:00:00:00:20:d4:14:11:80:00:20:d4:00:d6:c0:00 confirm(y/n)? : y switch_prompt # switch_prompt # show busclient 0 client table ent...

  • Page 50

    2-22 smartswitch atm switch reference manual buserrorlog console commands buserrorlog use buserrorlog to display or clear the bus error log associated with an elan. Note use the add buselan or modify buselan commands to enable or disable the bus error log for a specified elan. Operators clear, show ...

  • Page 51

    Smartswitch atm switch reference manual 2-23 console commands buserrorlog examples switch prompt # show buserrorlog elannumber(all) : 1 error log entries for vlan : 1 atm address errorcode sysuptime 39:1:2:3:4:5:6:7:8:9:0:1:2:3:4:5:6:7:8:9 22 01:02:03 switch prompt # clear buserrorlog elannumber(all...

  • Page 52

    2-24 smartswitch atm switch reference manual buselan console commands buselan use buselan to manage characteristics of a bus for a specified elan. If an les corresponding to the bus exists, the characteristics of the bus should match those of the les. Operators add, delete, modify, show parameters i...

  • Page 53

    Smartswitch atm switch reference manual 2-25 console commands buselan descriptions [atm address] atm address of the elan. [max frame size] maximum transfer unit assigned for this client. (same as the [mtu] input parameter.) [connection method] type of connection used. (same as the [connectmethod] in...

  • Page 54

    2-26 smartswitch atm switch reference manual buselan console commands examples switch_prompt # add buselan elannumber(0) : 102 elanname(elan102) : connectmethod(svc) : elantype(802.3) : multipoint(yes) : mtu(1516) : errorlogenable(no) : minimumtdenable(no) : forwardpeakcellrate() : switch_prompt # s...

  • Page 55

    Smartswitch atm switch reference manual 2-27 console commands buselan the example below changes elan102 from an ethernet buselan to a token ring buselan, changing the mtu to reflect the change in elan type. It assumes the les has already been changed. Switch_prompt # modify buselan 102 elanname(elan...

  • Page 56

    2-28 smartswitch atm switch reference manual buslecstat console commands buslecstat use buslecstat to display traffic statistics for clients connected to a bus. Operator show parameters descriptions input parameter description value/field size default [elannumber] number of the elan to which the bus...

  • Page 57

    Smartswitch atm switch reference manual 2-29 console commands buslecstat examples switch_prompt # show buslecstat elannumber(0) : lecid(0) : client statistics for elan elan000 =========================================================================== lecid : 1 atm address : 39:00:00:00:00:00:00:00:...

  • Page 58

    2-30 smartswitch atm switch reference manual busstat console commands busstat use busstat to display or clear statistics of a bus for an elan. Operators show, clear parameters descriptions input parameter description value/field size default [elannumber] number of the elan to which the bus belongs. ...

  • Page 59

    Smartswitch atm switch reference manual 2-31 console commands busstat examples switch_prompt # show busstat 3 elan elan003 statistics out octets : 450432 out unicast : 7030 out multicast : 3 in octets : 450432 in unicast : 7030 in multicast : 3 frame timeouts : 0 vcc rejects : 0 switch_prompt # swit...

  • Page 60

    2-32 smartswitch atm switch reference manual bustype console commands bustype use bustype to enable/disable intelligent bus mode. Note if intelligent bus mode is enabled, a unicast packet sent to the bus is forwarded only to the lane client whose destination address is specified in the packet. If in...

  • Page 61

    Smartswitch atm switch reference manual 2-33 console commands caceqbwallocscheme caceqbwallocscheme use caceqbwallocscheme to set or display the equivalent bandwidth allocation scheme of switch ports. Operators modify, show parameters descriptions input parameter description value/field size default...

  • Page 62

    2-34 smartswitch atm switch reference manual caceqbwallocscheme console commands examples switch_prompt # show caceqbwallocscheme portnumber(all) : =========================================================== port# alloc scheme for cbr rtvbr nrtvbr ubr abr ============================================...

  • Page 63

    Smartswitch atm switch reference manual 2-35 console commands cacinfo cacinfo use cacinfo to display bandwidth allocated to switch ports per service category. Operators show parameters descriptions input parameter description value/field size default [portnumber] port number on the switch. You can s...

  • Page 64

    2-36 smartswitch atm switch reference manual cacinfo console commands examples switch_prompt # show cacinfo portnumber(all) : all bandwidthunit(cps) : cps ===================================================================== port# total total bw bwalloc for servicecategory bw allocated cbr rt-vbr nr...

  • Page 65

    Smartswitch atm switch reference manual 2-37 console commands cacportbw cacportbw use cacportbw to display minimum and maximum bandwidth of switch ports. Operators show parameters input parameter description value/field size default [portnumber] port number on the switch. You can specify a physical ...

  • Page 67

    Smartswitch atm switch reference manual 2-39 console commands cacserviceclassbw cacserviceclassbw use cacserviceclassbw to set or display the bandwidth allocated to each service category. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module w...

  • Page 68

    2-40 smartswitch atm switch reference manual cacserviceclassbw console commands descriptions [maxbandwidthinpercentage ubr] maximum bandwidth allocated for ubr. Zero or positive integer [maxbandwidthinpercentage abr] maximum bandwidth allocated for abr. Zero or positive integer output parameter desc...

  • Page 69

    Smartswitch atm switch reference manual 2-41 console commands cacserviceclassbw examples switch_prompt # modify cacserviceclassbw portnumber() : 1b1 maximumbandwidthin-percentage-cbr(25) : maximumbandwidthin-percentage-rtvbr(25) : maximumbandwidthin-percentage-nrtvbr(25) : maximumbandwidthin-percent...

  • Page 70

    2-42 smartswitch atm switch reference manual cacstatistics console commands cacstatistics use cacstatistics to show cac statistics for switch ports. Operators clear, show parameters descriptions examples input parameter description value/field size default [portnumber] port number on the switch. You...

  • Page 71

    Smartswitch atm switch reference manual 2-43 console commands cacstatistics switch_prompt # show cacstatistics portnumber() : 1a1 ================================================================ cac statistics ================================================================ global statistics : no of...

  • Page 72

    2-44 smartswitch atm switch reference manual client console commands client use client to manage lane and ip/atm clients on the switch. Clients on the switch are called local clients. Note use the laneclient attribute to add or modify a lane client. Use the ipatmclient attribute to add or modify an ...

  • Page 73

    Smartswitch atm switch reference manual 2-45 console commands client descriptions [lecs address] atm address of the lecs. [les address] atm address of the les. [lan type] type of elan. [mtu] maximum transfer unit assigned for this client. [ip netmask] ip netmask assigned to the client. Operator para...

  • Page 74

    2-46 smartswitch atm switch reference manual client console commands examples switch_prompt # delete client 4 ip/atm client4 address: 39:00:00:00:00:00:00:00:00:00:14:15:00:00:00:7a:01:01:5b:00 confirm(y/n)?:y switch_prompt # switch_prompt # show client clientnumber(all) : client type ip address ser...

  • Page 75

    Smartswitch atm switch reference manual 2-47 console commands client with the following example ( ), notice how you get the same amount of detail whether you specify the client or accept the default (all): switch_prompt # show client /d clientnumber(all) : lane client 1 =============================...

  • Page 76

    2-48 smartswitch atm switch reference manual clientarp console commands clientarp use clientarp to display the arp table maintained by each lane or ip/atm client on the switch. For a lane client, the table contains mappings of mac to atm addresses for destination clients. The mappings are supplied b...

  • Page 77

    Smartswitch atm switch reference manual 2-49 console commands clientarp examples switch_prompt # show clientarp clientnumber(all) : lane client 0 arp table mac address atm address ============================================================================= 00:20:d4:14:15:00 39:00:00:00:00:00:00:00:...

  • Page 78

    2-50 smartswitch atm switch reference manual clientstat console commands clientstat use clientstat to display packet count statistics of lane or ip/atm clients on the switch. Note clients on the switch are called local clients. Operators show parameters in the output parameter table below, ( ) appea...

  • Page 79

    Smartswitch atm switch reference manual 2-51 console commands clientstat descriptions examples the examples show statistics for all clients, detail ( ) for all clients, an ip/atm client, and a lane client. Switch_prompt # show clientstat clientnumber(all): [error packets] number of error packets rec...

  • Page 80

    2-52 smartswitch atm switch reference manual clientstat console commands client type rxpkts txpkts rxoctets txoctets ============================================================================ 1 lane 0 0 0 0 3 ip/atm 0 0 0 0 switch_prompt # switch_prompt # show clientstat /d clientnumber(all): stat...

  • Page 81

    Smartswitch atm switch reference manual 2-53 console commands clientstat stats for ip/atm client 3 ============================================================================ rx stats bytes received : 0 unicast packets : 0 multicast packets : 0 broadcast packets : 0 error packets : 0 dropped packet...

  • Page 82

    2-54 smartswitch atm switch reference manual clientvc console commands clientvc use clientvc to display vcs associated with arp mappings cached by lane or ip/atm clients on the switch. Clientarp is similar to clientvc but does not show the vpi/vci corresponding to a route to a destination client. No...

  • Page 83

    Smartswitch atm switch reference manual 2-55 console commands clientvc examples switch_prompt # show clientvc clientnumber(all) : lane client 0 vc table mac address vpi/vci atm address =========================================================================== 00:02:d4:14:22:80 0/2453 39:00:00:00:00...

  • Page 84

    2-56 smartswitch atm switch reference manual community console commands community use community to group nms (network management system) hosts by privilege level. Hosts are collectively called communities. Host privilege levels determine the type of information access permitted by the switch. The sw...

  • Page 85

    Smartswitch atm switch reference manual 2-57 console commands community examples switch_prompt # add community name() : boris ipaddr() : 90.1.1.1 priviledge(read) : switch_prompt # switch_prompt # show community community name ip address privilege ====================================================...

  • Page 86

    2-58 smartswitch atm switch reference manual config console commands config use config to erase the configuration information on the smartswitch 6500. Before using the clear config command, you should back up the switch configuration using the backup switch command. Operators clear, flush parameters...

  • Page 87

    Smartswitch atm switch reference manual 2-59 console commands consoletimeout consoletimeout use consoletimeout to set or display the timeout for the console interface. Operators modify, show parameters descriptions examples switch_prompt # set consoletimeout consoletimeout(0) : 0 you are about to di...

  • Page 88

    2-60 smartswitch atm switch reference manual coredump console commands coredump use coredump to dump the system cpu and/or common dram in the event of a system failure. The core is dumped to a file specified on a local ethernet host. To use coredump, the ethernet host must run tftp server software, ...

  • Page 89

    Smartswitch atm switch reference manual 2-61 console commands coredump descriptions examples switch_prompt # modify coredump enablecoredump(n) :y serverip() :204.95.77.240 coredumpfile() :/tftpboot/ssubrama/core username() :ssubrama userpassword() :password switch_prompt # show coredump coredumpenab...

  • Page 90

    2-62 smartswitch atm switch reference manual cpuswitchover console commands cpuswitchover (smartswitch 6500 only) use cpuswitchover to manually switch roles of the redundant (slave) and master tsm/cpu modules (the slave module becomes the master module and vice versa). The execute cpuswitchover comm...

  • Page 91

    Smartswitch atm switch reference manual 2-63 console commands csmswitchover csmswitchover (smartswitch 6500 only) use csmswitchover to manually switch roles of the redundant (slave) and master csm modules (the slave module becomes the master module and vice versa). The execute csmswitchover command ...

  • Page 92

    2-64 smartswitch atm switch reference manual ds3e3loopback console commands ds3e3loopback use ds3e3loopback to set or display loopback at ds3 or e3 ports. Note a port in loopback mode does not pass normal traffic. Operators modify, show parameters descriptions input parameter description value/field...

  • Page 93

    Smartswitch atm switch reference manual 2-65 console commands ds3e3loopback examples switch_prompt # show ds3e3loopback port(all) : port type loopback ============================================================================== 1d1 ds3 none 1d2 ds3 none 1d3 ds3 none 1d4 ds3 none switch_prompt # sw...

  • Page 94

    2-66 smartswitch atm switch reference manual elan console commands elan use elan to create or delete elans on the switch. It is a means to manage elan servers with one command. To manage elan servers individually, see the buselan, lecselan, and leselan attributes. Note the buselan, lecselan, and les...

  • Page 95

    Smartswitch atm switch reference manual 2-67 console commands elan [distribute] establishes the nature of the control distribute vcc. Possible values are: all or proxy. All establishes control distribute vcc to all clients. Proxy establishes control distribute vcc only to proxy clients. All, proxy p...

  • Page 96

    2-68 smartswitch atm switch reference manual elan console commands descriptions operator parameters/permissions description add elan [elannumber] [elanname] [connectmethod] [elantype] [multipoint] [mtu] [errorlogenable] [minimumtdenable] [forwardpeakcellrate] [backwardpeakcellrate] [distribute] admi...

  • Page 97

    Smartswitch atm switch reference manual 2-69 console commands elan examples switch_prompt # add elan elannumber(0) : 11 elanname(elan011) : connectmethod(svc) : elantype(802.3) : multipoint(yes) : mtu(1516) : errorlogenable(no) : minimumtdenable : forwardpeakcellrate() : backwardpeakcellrate() : dis...

  • Page 98

    2-70 smartswitch atm switch reference manual elanmcast console commands elanmcast use elanmcast to display multicast group mac addresses served by an elan. Operators show parameters descriptions examples switch_prompt # show elanmcast 0 multicast entries for vlan : 0 --------------------------------...

  • Page 99

    Smartswitch atm switch reference manual 2-71 console commands eventdisplay eventdisplay use eventdisplay to enable/disable the display of event messages on the console screen. Note use events to display the events currently logged. Operators modify, show parameters this attribute has no output param...

  • Page 100

    2-72 smartswitch atm switch reference manual events console commands events use events to display or delete events currently logged. Note .Üi˜ÍÃÊ>ÀiʘœÍÊ«iÀÈÃÍi˜ÍÊœ˜ÊÀilœœÍÊ->ÀiʘœÍÊÀiÍ>ˆ˜i`ʈ˜ÊÍ…iÊiÜi˜ÍÊ•œ}®° operators delete, show parameters this attribute has no output parameters. Descriptions i...

  • Page 101

    Smartswitch atm switch reference manual 2-73 console commands events examples switch_prompt # show events index(all) : 0 33554656 minor event 001:27:50:708 --------------------------------------------------- sendto failed for ip address 206.61.231.153 1 33554656 minor event 001:27:51:612 -----------...

  • Page 102

    2-74 smartswitch atm switch reference manual exit console commands exit use exit to disconnect your console connection from the switch. Operator exit parameters this attribute has no parameters. Just enter exit at the switch prompt. Descriptions examples switch_prompt # exit exiting smartswitch comm...

  • Page 103

    Smartswitch atm switch reference manual 2-75 console commands firmware firmware use firmware to download switch software from a tftp server. Operators update parameters this attribute has no output parameters. Descriptions input parameter description value/field size default [serverip] ip address of...

  • Page 104

    2-76 smartswitch atm switch reference manual firmware console commands examples switch_prompt # update firmware serverip() : 206.61.237.127 path(public/smart6500_1.Ima) : builds/lab-02.02.22/ser ver.Ima you are updating the code image in the flash. Are you sure this is what you want to do? Confirm(y...

  • Page 105

    Smartswitch atm switch reference manual 2-77 console commands history history use history to view or repeat one of the last five console commands entered. Operators history parameters this attribute has no parameters. Just enter history at the switch prompt. Descriptions examples switch_prompt # his...

  • Page 106

    2-78 smartswitch atm switch reference manual ilmiconfig console commands ilmiconfig use ilmiconfig to manage ilmi timers specified in ilmi 4.0 and to enable or disable ilmi functions. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when ...

  • Page 107

    Smartswitch atm switch reference manual 2-79 console commands ilmiconfig note the following applies to smartswitch 6500 only: if you hot-swap a tsm with a tsm of a different type (different i/o ports), ilmi timer information associated with ports on the original tsm is deleted. Before you insert a r...

  • Page 108

    2-80 smartswitch atm switch reference manual ilmiconfig console commands examples switch prompt # modify ilmiconfig port ilmi address ilmi timer s timer t factor k registration connectivity (seconds) (seconds) =================================================================== 1a1 enabled enabled 1 ...

  • Page 109

    Smartswitch atm switch reference manual 2-81 console commands ipaddress ipaddress use ipaddress to change ip addresses of the ethernet port and ip netmask on the switch. Operators modify parameters this attribute has no output parameters. Descriptions examples switch_prompt # modify ipaddress ipaddr...

  • Page 110

    2-82 smartswitch atm switch reference manual ipatmarp console commands ipatmarp use ipatmarp to display the arp server table for an ip/atm vlan. The arp server table contains mappings of ip to atm addresses for destination clients on the vlan. Operators show parameters descriptions examples switch_p...

  • Page 111

    Smartswitch atm switch reference manual 2-83 console commands ipatmclient ipatmclient use ipatmclient to add or modify ip/atm clients on the switch. Any of the clients can act as an arp server. Note use the client attribute to delete, restart, or show ip/atm clients. Operators add, modify parameters...

  • Page 112

    2-84 smartswitch atm switch reference manual ipatmclient console commands descriptions operator parameters/permissions description add ipatmclient [clientnumber] [servertype] [serveraddress] [ipaddress] [netmask] [mtu] administrator creates a new ip/atm client on the switch. If the circuits in this ...

  • Page 113

    Smartswitch atm switch reference manual 2-85 console commands ipatmclient examples switch_prompt # add ipatmclient clientnumber(0) : 50 servertype(none) : local serveraddr() : ipaddr() : 101.1.1.50 netmask(255.0.0.0): mtu(9180) : switch_prompt # switch_prompt # add ipatmclient clientnumber(0) : 1 se...

  • Page 114

    2-86 smartswitch atm switch reference manual ipatmpvc console commands ipatmpvc use ipatmpvc to manage ip/atm pvcs. Note the following applies to the smartswitch 2500 family only: the delete ipatmpvc command removes the specified ipatmpvc as well as the pvc associated with it. Operators add, delete,...

  • Page 115

    Smartswitch atm switch reference manual 2-87 console commands ipatmpvc examples switch_prompt # add pvc conntype(ptp) : port-1-number() : 1a1 port-1-vpci : 0 port-1-vci() : 130 port-2-number() : cpu port-2-vpci() : 0 port-2-vci() : 130 port1-to-port2trafficdescriptorindex() : 1 port2-to-port1traffic...

  • Page 116

    2-88 smartswitch atm switch reference manual ipatmpvc console commands switch_prompt # show client 0 ip/atm client 0 =========================================================================== client state : operational client address : 39:00:00:00:00:00:00:00:20:d4:14:22:80:00:00:0a:01:01:02:00 ser...

  • Page 117

    Smartswitch atm switch reference manual 2-89 console commands ipatmstat ipatmstat use ipatmstat to display statistics for an ip/atm client that acts as an arp server. Operator show parameters descriptions input parameter description value/field size default [clientnumber] number of the client. 0-125...

  • Page 118

    2-90 smartswitch atm switch reference manual ipatmstat console commands examples switch_prompt # show ipatmstat clientnumber(all): client arpreqs arpreps arpunrch arpnaks =========================================================================== 50 0 0 0 0 51 0 0 0 0 switch_prompt # switch_prompt #...

  • Page 119

    Smartswitch atm switch reference manual 2-91 laneclient use laneclient to add or modify lane clients on the switch. (add a lane client on the switch if you want to access the switch console using lane.) note use the client attribute to delete, restart, or show lane clients. Operators add, modify par...

  • Page 120

    2-92 smartswitch atm switch reference manual laneclient description examples switch_prompt # add laneclient clientnumber(0) :100 lanname(elan100): servertype(lecs): serveraddress() :39:00:00:00:00:00:11:11:11:11:11:11:11:00:11:22:22:44:55:01 ipaddress() :101.1.1.100 netmask(255.0.0.0): mtu(1516) : s...

  • Page 121

    Smartswitch atm switch reference manual 2-93 lecmcast lecmcast use lecmcast to display multicast groups registered by a lane client. Operators show parameters. Descriptions input parameter description value/field size default [elannumber] elan number. 0-125 0 [lecid] lec id of the client. 1-65279 or...

  • Page 122

    2-94 smartswitch atm switch reference manual lecmcast examples switch_prompt # show lecmcast 0 lecid(0) : lecid:2, atmaddr: 39:00:00:00:00:00:00:00:00:00:28:e8:80:00:00:1d:6b:6e:cc:01 ---------------------------------------------------------------------------- mcastid : 2 group mac address : 01:80:c...

  • Page 123

    Smartswitch atm switch reference manual 2-95 lecs lecs use lecs to manage the lecs on the network. Operators show, start, stop parameters this attribute has no parameters. Just enter start lecs or stop lecs at the switch prompt. Descriptions note the status of the lecs is persistent on reboot. If yo...

  • Page 124

    2-96 smartswitch atm switch reference manual lecselan lecselan use lecselan to manage elan entries at the lecs. Operators add, delete, modify, show parameters input parameter description value/field size default [elannumber] number of the elan to add to the lecs. 0-125 0 [elanname] name of elan to a...

  • Page 125

    Smartswitch atm switch reference manual 2-97 lecselan descriptions operator parameters/permissions description add lecselan [elannumber] [elanname] [lesaddress] [elantype] [mtu] [tlvset] administrator creates a specified elan on the lecs. Enter add lecselan to add an elan the long way—with the add b...

  • Page 126

    2-98 smartswitch atm switch reference manual lecselan examples switch_prompt # add lecselan elannumber(0) : 4 elanname(elan004) : lesaddress(39:00:00:00:00:00:00:00:00:00:14:15:00:00:20:d4:14:15:04:02): elantype(802.3) : mtu(1516) : tlvset() : switch_prompt # switch_prompt # delete lecselan elannumb...

  • Page 127

    Smartswitch atm switch reference manual 2-99 lecselanlec lecselanlec use lecselanlec to manage the way an lecs configures (assigns) a lane client to an elan using the bybesteffort assignment policy. At least one instance of the bybesteffort assignment policy is always in effect at the lowest priorit...

  • Page 128

    2-100 smartswitch atm switch reference manual lecselanlec descriptions [ip address] ip address of the client. [tlv set] tlv set associated with the client. Operator parameters/permissions description add lecselanlec [lecaddress] clientatmaddress> [macaddress/routedesc] [elannumber] administrator map...

  • Page 129

    Smartswitch atm switch reference manual 2-101 lecselanlec examples switch_prompt # add lecselanlec lecaddress: 39:00:00:00:00:00:00:00:00:00:14:7b:00:00:20:d4:14:7b:00:01 macaddress/routedesc: 01:02:03:04:05:06 elannumber(0):1 switch_prompt # switch_prompt # delete lecselanlec lecaddress/macddress/r...

  • Page 130

    2-102 smartswitch atm switch reference manual lecselannametable lecselannametable use lecselannametable to manage the elan name table. The table maps names with elan numbers. The table determines how an lecs assigns a lane client to an elan using the byelanname assignment policy. Note use lecselanpo...

  • Page 131

    Smartswitch atm switch reference manual 2-103 lecselannametable examples switch_prompt # show lecselannametable elan id elan name ============================================================================== 0 elan1 switch_prompt #.

  • Page 132

    2-104 smartswitch atm switch reference manual lecselanpolicy lecselanpolicy use lecselanpolicy to manage the elan assignment policy table. Elan policies determine how lane clients are configured (assigned) to elans by the lecs. The lecs uses the policy with the highest priority first, the policy wit...

  • Page 133

    Smartswitch atm switch reference manual 2-105 lecselanpolicy descriptions operator parameters/permissions description add lecselanpolicy [policyindex] [type] [priority] administrator adds an entry to the elan policy table. Delete lecselanpolicy [policyindex] administrator deletes an entry from the e...

  • Page 134

    2-106 smartswitch atm switch reference manual lecselanpolicy examples switch_prompt # show lecselanpolicy index assignment policy priority value ============================================================================== 1 best effort (proprietary) 65001 2 by atm address 2000 7 by route descripto...

  • Page 135

    Smartswitch atm switch reference manual 2-107 lecserrorlog lecserrorlog use lecserrorlog to display the log maintained by the lecs to track configuration request failures. You can control the log using lecserrorlogcontrol. Note the log can contain up to 128 entries. After 128 entries, no additional ...

  • Page 136

    2-108 smartswitch atm switch reference manual lecserrorlog examples switch_prompt # delete lecserrorlog switch_prompt # switch_prompt # show lecserrorlog atm address errorcode sysuptime ============================================================================== 39:00:00:00:00:00:00:00:00:00:14:17...

  • Page 137

    Smartswitch atm switch reference manual 2-109 lecserrorlogcontrol lecserrorlogcontrol use lecserrorlogcontrol to control the lecs error log. The lecs error log contains information on lecs configuration request failures. Operators modify, show parameters descriptions input parameter description valu...

  • Page 138

    2-110 smartswitch atm switch reference manual lecserrorlogcontrol examples switch_prompt # set lecserrorlogcontrol errorlogstatus(disabled) : enable switch_prompt # switch_prompt # show lecserrorlogcontrol administrative status : disabled operation status : disabled clear log flag : no operation log...

  • Page 139

    Smartswitch atm switch reference manual 2-111 lecsneighbor lecsneighbor use lecsneighbor to add or delete lecs synchronization neighbors. The lecs neighbors are on other switches and communicate with the lecs on this switch (local lecs). The lecs neighbors provide the local lecs with information abo...

  • Page 140

    2-112 smartswitch atm switch reference manual lecsneighbor examples switch_prompt # add lecsneighbor neighboratmaddress() : switch_prompt # delete lecsneighbor neighboratmaddress() :.

  • Page 141

    Smartswitch atm switch reference manual 2-113 lecsneighborinfo lecsneighborinfo use lecsneighborinfo to display status information about lecs neighbors. The lecs neighbors are remote lecs servers that are known to (communicate with) the lecs on the switch (local lecs). The information includes the i...

  • Page 142

    2-114 smartswitch atm switch reference manual lecsserverlist lecsserverlist use lecsserverlist to display the list of les/bus servers known to the lecs on the switch (local lecs). The information is sorted by elan number (according to elans supported by the les/bus servers). The les/bus servers can ...

  • Page 143

    Smartswitch atm switch reference manual 2-115 lecsserverlist descriptions examples switch_prompt # show lecsserverlist elannumber(all) : 0 les servers known for elan 0 ============================================================================== atm address : 39:00:00:00:00:00:00:00:00:00:14:bf:80:...

  • Page 144

    2-116 smartswitch atm switch reference manual lecspacketsizes lecspacketsizes use lecspacketsizes to manage the elan packet size table. The table maps packet sizes (mtus) with elan numbers. The table determines how an lecs assigns a lane client to an elan using the bypacketsize assignment policy. No...

  • Page 145

    Smartswitch atm switch reference manual 2-117 lecspacketsizes examples switch_prompt # add lecspacketsizes elannumber(0) : 1 packetsize(0) : 1516 switch_prompt # switch_prompt # delete lecspacketsizes elannumber(0) : 1 packetsize(0) : 1516 switch_prompt # switch_prompt # show lecspacketsizes elan id...

  • Page 146

    2-118 smartswitch atm switch reference manual lecsstat lecsstat use lecsstat to display statistics on configuration requests to the lecs. Operator show parameters this attribute has no input parameters. Description output parameter description [successful configuration requests] number of successful...

  • Page 147

    Smartswitch atm switch reference manual 2-119 lecsstat example switch_prompt # show lecsstat statistics on lecs =========================================================================== successful configuration requests : 3 bad configuration requests : 0 invalid request parameters : 1 insufficient...

  • Page 148

    2-120 smartswitch atm switch reference manual lecstlvparam lecstlvparam use lecstlvparam to remove a tlv parameter from a tlv set on the lecs. Operators delete parameters descriptions examples the show lecstlvset example is used here to show how delete lecstlvparam works. Observe that [2] in show le...

  • Page 149

    Smartswitch atm switch reference manual 2-121 lecstlvparam switch_prompt # show lecstlvset tlvsetnumber(all) :2 tlvindex tlvdescription value =========================================================================== tlvset 2 : 1 control timeout 200 2 max unknown frame time 4 6 arp aging time 250 7...

  • Page 150

    2-122 smartswitch atm switch reference manual lecstlvset lecstlvset use lecstlvset to manage tlv parameters on the lecs. A tlv set is a collection of tlv parameters associated with an elan. Operators add, delete, modify, show parameters input parameter description value/field size default [tlvsetnum...

  • Page 151

    Smartswitch atm switch reference manual 2-123 lecstlvset [flushtimeout] time limit on flush response after flush request has been sent, before taking recovery action. 1-4 seconds no default [pathswitchingdelay] time since sending a frame to the lecs after which the lane client may assume that the fr...

  • Page 152

    2-124 smartswitch atm switch reference manual lecstlvset descriptions [mpcmaxretrytime] mpc retry time maximum. Output parameter description [tlvindex] number that identifies the specific tlv parameter in the tlv set. [tlvdescription] description of the tlv parameter. [value] value of the tlv parame...

  • Page 153

    Smartswitch atm switch reference manual 2-125 lecstlvset modify lecstlvset [tlvsetnumber] tlvsetnumber> [controltimeout] controltimeout> [maxunknownframecount]maxunknframecount> [maxunknownframetime]maxunknframetime> [vcctimeout] vcctimeout> [maxretrycount] maxretrycount> [arpagingtime] arpagingtime...

  • Page 154

    2-126 smartswitch atm switch reference manual lecstlvset examples switch_prompt # add lecstlvset tlvsetnumber[1-32767](1) : 3 controltimeout[10-300]() : 200 maxunknownframecount[1-10]() : 5 maxunknownframetime[1-60]() : 50 vcctimeout[0-65535]() : 50000 maxretrycount[0-2]() : 1 arpagingtime[10-300]()...

  • Page 155

    Smartswitch atm switch reference manual 2-127 lecstlvset mpskeepalivetime() : mpskeepalivelifetime() : mpsinternetprotocols() : mpsinitialretrytime() : mpsretrytimemaximum() : mpsgiveuptime() : mpsdefaultholdingtime() : mpcsetupframecount() : mpcsetupframetime() : mpcflowprotocols() : mpcretrytime()...

  • Page 156

    2-128 smartswitch atm switch reference manual lecsvcc lecsvcc use lecsvcc to display vccs queued to join the lecs. A lane client sets the vccs up as part of the lecs connection. You can display but not modify the vccs (they are not modifiable). As soon as a client joins the lecs, the vccs are no lon...

  • Page 157

    Smartswitch atm switch reference manual 2-129 les les use les to start and stop the bus and les for an elan. Operators show, start, stop parameters this attribute has no parameters. Just enter start les or stop les at the switch prompt. Descriptions examples switch_prompt # start les notice - 'zless...

  • Page 158

    2-130 smartswitch atm switch reference manual lesarp lesarp use lesarp to display the arp server table for a specified elan. The arp server table is maintained by the les for the elan. Operators show parameters descriptions example switch_prompt # show lesarp elannumber(0) : 1 arp table entries for ...

  • Page 159

    Smartswitch atm switch reference manual 2-131 lesclient lesclient use lesclient to manage the mapping between the les and the lane clients registered with it. Each lane client is identified uniquely by its lec id. Operators delete, show parameters descriptions input parameter description value/field...

  • Page 160

    2-132 smartswitch atm switch reference manual lesclient examples switch_prompt # delete lesclient elannumber (0): lecid (0) : 12 confirm? (y/n) : y switch_prompt # switch_prompt # show lesclient elannumber (0): client table entries for elan elan000 ===================================================...

  • Page 161

    Smartswitch atm switch reference manual 2-133 leselan leselan use leselan to manage characteristics of an les for a specified elan. If a bus corresponding to the les exists, the characteristics of the les should match those of the bus. Operators add, delete, modify, show parameters input parameter d...

  • Page 162

    2-134 smartswitch atm switch reference manual leselan descriptions [distribute] establishes nature of control distribute vcc. Possibie values are: all or proxy. All establishes control distribute vcc to all clients. Proxy establishes control distribute vcc only to proxy clients. All, proxy proxy [bu...

  • Page 163

    Smartswitch atm switch reference manual 2-135 leselan examples the following example creates elan 102 with default parameters for les: switch_prompt # add leselan elannumber(0) : 102 elanname(elan102) : connectmethod(svc) : elantype(802.3) : multipoint(yes) : mtu(1516) : distribute(proxy) : busatmad...

  • Page 164

    2-136 smartswitch atm switch reference manual leselan the following example resets an elan with default parameters: switch_prompt # modify leselan elannumber(0) : 102 elanname(elan102) : connectmethod(svc) : elantype(802.3) : multipoint(yes) : mtu(1516) : 9234 errorlogenable(no) : minimumtdenable(no...

  • Page 165

    Smartswitch atm switch reference manual 2-137 leserrorlog leserrorlog use leserrorlog to display or clear the les error log associated with an elan. Note use the add leselan or modify leselan commands to enable or disable the les error log for a specified elan. Operators delete, show parameters desc...

  • Page 166

    2-138 smartswitch atm switch reference manual leserrorlog table 2-7 leserrorlog error codes code name meaning 0 success successful response 1 version not supported version field of request contains a value higher than that supported. 2 invalid request parameters the parameters given are incompatible...

  • Page 167

    Smartswitch atm switch reference manual 2-139 leserrorlog examples switch prompt # show leserrorlog elannumber(all) : 1 error log entries for vlan : 1 atm address errorcode sysuptime 39:1:2:3:4:5:6:7:8:9:0:1:2:3:4:5:6:7:8:9 22 01:02:03 switch prompt # clear leserrorlog elannumber(all) : 1 clearing a...

  • Page 168

    2-140 smartswitch atm switch reference manual leslecstat leslecstat use leslecstat to display traffic characteristics for clients registered with an les. Operators show parameters descriptions input parameter description value/field size default [elannumber] number of the elan to which the les belon...

  • Page 169

    Smartswitch atm switch reference manual 2-141 leslecstat examples switch_prompt # show leslecstat elannumber(0) : lecid(0) : 3 client 3 statistics for elan elan000 =========================================================================== atm address : 39:00:00:00:00:00:00:00:20:d4:14:22:80:00:20:d...

  • Page 170

    2-142 smartswitch atm switch reference manual leslnniinfo leslnniinfo use leslnniinfo to show information on vccs established for an instance of les/bus servers. The vccs are established for lnni purposes. Each instance of les/bus servers establishes two point-to-multipoint and one or more point-to-...

  • Page 171

    Smartswitch atm switch reference manual 2-143 leslnniinfo descriptions examples switch_prompt # show leslnniinfo elannumber(all) : lnni information for elan 0 ============================================================================== les configure direct vcc : 0/35 les control coordinate vcc (pm...

  • Page 172

    2-144 smartswitch atm switch reference manual leslnnistat leslnnistat use leslnnistat to display or clear statistics on control and data packets to or from all les/bus servers that support a particular elan. The display shows statistics for forwarded packets on a global basis (for all neighbors) and...

  • Page 173

    Smartswitch atm switch reference manual 2-145 leslnnistat descriptions [arp responses received] arp responses received from the neighbor les. [narp requests received] narp requests received from the neighbor les. [flush requests received] flus requests received from the neighbor les. [flush response...

  • Page 174

    2-146 smartswitch atm switch reference manual leslnnistat examples switch_prompt # show leslnnistat elannumber(all) : lnni statistics for elan 0 ============================================================================== arp requests forwarded : 0 arp responses forwarded : 0 narp requests forward...

  • Page 175

    Smartswitch atm switch reference manual 2-147 lesstat lesstat use lesstat to display or clear statistics of an les for an elan. Operators show, clear parameters input parameter description value/field size default [elannumber] number of elan to which the les belongs. 0-125 or all all output paramete...

  • Page 176

    2-148 smartswitch atm switch reference manual lesstat descriptions [reg. Access denied errors] access denied errors for register request. [join invalid requestid errors] invalid lecid errors for join request. [reg. Invalid requestid errors] invalid lecid errors for register request. [join invalid la...

  • Page 177

    Smartswitch atm switch reference manual 2-149 lesstat examples switch_prompt # show lesstat elannumber(all) :102 elan : elan102 statistics join ok : 0 join version not supported errors : 0 reg. Version not supported errors : 0 unreg. Version not supported errors : 0 join invalid request param errors...

  • Page 178

    2-150 smartswitch atm switch reference manual linkmonitortimeout linkmonitortimeout use linkmonitortimeout to set or show the link monitor timeout value for switch ports. The timeout value is the number of seconds a port waits without traffic before releasing all resources for connections to it. Ope...

  • Page 179

    Smartswitch atm switch reference manual 2-151 lnniinfo lnniinfo use lnniinfo to set or display lnni parameters on the switch. Lnniinfo is one of two attributes that apply to general lnni configuration (the other is lnnistatus). Operators modify, show parameters descriptions input parameter descripti...

  • Page 180

    2-152 smartswitch atm switch reference manual lnniinfo examples switch_prompt # show lnniinfo lecs id : 2 switch_prompt # modify lnniinfo lecsid(2) : 3 switch_prompt # show lnniinfo lecs id : 3.

  • Page 181

    Smartswitch atm switch reference manual 2-153 lnnistatus lnnistatus use lnnistatus to enable or disable lnni support on the switch. In addition, use lnnistatus to selectively enable or disable use of server cache synchronization protocol (scsp) when lnni is enabled. Lnnistatus is one of two attribut...

  • Page 182

    2-154 smartswitch atm switch reference manual lnnistatus examples switch_prompt # modify lnnistatus lnnistatus(disabled) : enable scspstatus(disabled) : switch_prompt # show lnnistatus lnni status : enabled scsp status : disabled switch_prompt #.

  • Page 183

    Smartswitch atm switch reference manual 2-155 mcastclients mcastclients use mcastclients to display clients associated with a multicast group. Operators show parameters descriptions input parameter description value/field size default [elannumber] elan number associated with the multicast group. 0-1...

  • Page 184

    2-156 smartswitch atm switch reference manual mcastclients examples switch_prompt # show mcastclients 0 mcastid: 2, group macaddr : 01:80:c2:00:00:00 ------------------------------------------------- lecid : 2 atm address : 39:00:00:00:00:00:00:00:00:00:28:e8:80:00:00:1d:6b:6e:cc:01 selective mcast ...

  • Page 185

    Smartswitch atm switch reference manual 2-157 minmaxtableindex minmaxtableindex 2ÃiÊ ˆ˜ >Þ0>l•i7˜`iÞÊÍœÊ`ˆÃ«•>ßÊ«œÃÈl•iÊÜ>•ÖiÃÊvœÀÊ“ˆ˜ˆ“Ö“Ê>˜`Ê“>Þˆ“Ö“Êvi••ÊÍ…ÀiÃ…œ•`Ê>ÍÊÃ݈Ív…Ê«œÀÍðÊÊ0…iÊÍ>l•iÊ “>«ÃÊÍ…ÀiÃ…œ•`ÊÜ>•ÖiÃÊ͜ʈ˜`iÞʘ֓liÀðÊÊ0…iʈ˜`iÞʘ֓liÀÃÊ>ÀiÊ«>À>“iÍiÀÃÊœvÊÍ…iÊ modify porttrafficcong...

  • Page 186

    2-158 smartswitch atm switch reference manual mynmaddr mynmaddr use mynmaddr to manage the switch through the specified ip address. Operators modify, show parameters descriptions examples switch_prompt # modify mynmaddr ipaddr() : 204.95.75.186 my nm ip-address : 204.95.75.186 switch_prompt # switch...

  • Page 187

    Smartswitch atm switch reference manual 2-159 netprefix netprefix use netprefix to set or display network atm address prefixes on a particular port. The 13-byte net prefix is based on a hierarchical addressing scheme. The default value starts with the first byte set to 39 (dcc address format), follo...

  • Page 188

    2-160 smartswitch atm switch reference manual netprefix note the following applies to smartswitch 6500 only: if you hot-swap a tsm with a tsm of a different type (different i/o ports), net prefix information associated with ports on the original tsm is deleted. Before you insert a replacement tsm, y...

  • Page 189

    Smartswitch atm switch reference manual 2-161 netprefix examples switch_prompt # show netprefix portnumber :( all ): port# netprefix =============================================================== 1a2 39:00:00:00:00:00:00:00:00:00:20:d4:14:16:00 switch_prompt # switch_prompt # add netprefix portnumb...

  • Page 190

    2-162 smartswitch atm switch reference manual networkclock networkclock use networkclock to set or display the port used as the network clock source. Operators modify, show parameters this attribute has no output parameters. Descriptions examples switch_prompt # set networkclock portnumber(cpu) : sw...

  • Page 191

    Smartswitch atm switch reference manual 2-163 passwd passwd use passwd to change the password of the current or lower-privileged user. Operators passwd parameters descriptions examples switch_prompt # passwd old password: admin changing password for user administrator new password: levelone reenter ...

  • Page 192

    2-164 smartswitch atm switch reference manual ping ping use ping to test ip connectivity of a client. Note the client must be on the same subnet or it must be reachable by routing from the subnet that is pinging. Operators start parameters descriptions examples switch_prompt # start ping destip() : ...

  • Page 193

    Smartswitch atm switch reference manual 2-165 pnniinterface pnniinterface use pnniinterface to set or display characteristics to configure a switch port for pnni routing. Operators modify, show parameters input parameter description value/field size default [portnumber] port number on the switch. Yo...

  • Page 194

    2-166 smartswitch atm switch reference manual pnniinterface descriptions output parameter description [port number] port number on the switch. [admnwt cbr] administrative weight for the constant bit rate (cbr) service category. [admnwt rtvbr] administrative weight for the realtime variable bit rate ...

  • Page 195

    Smartswitch atm switch reference manual 2-167 pnniinterface examples switch_prompt # modify pnniinterface portnumber() : 1a1 admnwtcbr(100) : admnwtrtvbr(100) : admnwtnrtvbr(100) : admnwtabr(100) : admnwtubr(100) : aggregationtoken(0) : rccservcategory(nrtvbr) : switch_prompt # switch_port # show pn...

  • Page 196

    2-168 smartswitch atm switch reference manual pnnilink pnnilink use pnnilink to display characteristics of all pnni links connected directly to the switch. The characteristics include operation of each link and the relationship between each link and the nodes it connects. Note use pnninetworklink to...

  • Page 197

    Smartswitch atm switch reference manual 2-169 pnnilink description [pnni version] for lowest-level horizontal and unknown link types, this attribute indicates the version of pnni routing protocol used to exchange information. If communication with the neighbor node has not yet been established, then...

  • Page 198

    2-170 smartswitch atm switch reference manual pnnilink examples switch_prompt # show pnnilink num(all) : num port node remote node hello state link type number index ip addr =========================================================================== 1 7a3 1 206.61.237.19 2wayinside lowest level hori...

  • Page 199

    Smartswitch atm switch reference manual 2-171 pnnimetrics pnnimetrics use pnnimetrics to manage pnni metrics that apply to a logical node on the switch. Operators add, delete, show parameters input parameter description value/field size default [metricstag] number associated with a group of traffic ...

  • Page 200

    2-172 smartswitch atm switch reference manual pnnimetrics [celllossrateforclp=0+1] cell loss ratio for clp=0+1 traffic for the specified service category. The cell loss ratio is computed as 10 (-n) where n is the value here. [cellratemargin] cell rate margin (in cells per second) for the specified s...

  • Page 201

    Smartswitch atm switch reference manual 2-173 pnnimetrics descriptions [cell rate margin] cell rate margin (in cells per second) for the specified service category. [variance factor] variance factor in units of 2 (-8) for the specified service category. Operator parameters / permissions description ...

  • Page 202

    2-174 smartswitch atm switch reference manual pnnimetrics examples switch_prompt # show pnnimetrics metricstag(all) : metrics tag direction metrics index gcac clp admin wt service categories =========================================================================== 3 outgoing 2 clp0+1 5040 abr 1118...

  • Page 203

    Smartswitch atm switch reference manual 2-175 pnnimetrics ================================================================================ metrics tag : 3 direction : outgoing metrics index : 2 service categories : abr gcac clp : clp0+1 admin wt : 5040 maximum cell rate : 3 (cells/second) available ...

  • Page 204

    2-176 smartswitch atm switch reference manual pnnineighbor pnnineighbor use pnnineighbor to display pnni neighbors of any logical node on the switch. The pnni neighbors are themselves logical nodes on other switches. Each pnni neighbor is linked directly to one of the local logical nodes. (the logic...

  • Page 205

    Smartswitch atm switch reference manual 2-177 pnnineighbor descriptions [rcv ptsps] number of ptsps received from the neighbor node. [xmt ptsps] number of ptsps (re)transmitted to the neighbor node. [rcv ptse reqs] number of ptse request packets received from the neighbor node. [xmt ptse reqs] numbe...

  • Page 206

    2-178 smartswitch atm switch reference manual pnnineighbor examples switch_prompt # show pnnineighbor num(all) : num neighbor node neighbor node id state ip addr. ======================================================================================= 1 206.61.237.213 60:a0:39:00:00:00:00:00:00:00:00...

  • Page 207

    Smartswitch atm switch reference manual 2-179 pnninetworklink pnninetworklink use pnninetworklink to display characteristics of the pnni hierarchy as seen from a logical node on the switch. The characteristics include the operation of all links and nodes known to the logical node through the exchang...

  • Page 208

    2-180 smartswitch atm switch reference manual pnninetworklink descriptions [index] an index into the set of link and nodal connectivity associated with the originating node and port. This index is needed since there may be multiple entries for nodal connectivity from a specific node and port pair. [...

  • Page 209

    Smartswitch atm switch reference manual 2-181 pnninetworklink examples switch_prompt # show pnninetworklink num(all) : originating node id orig port id num remote node id remote port id ================================================================================ 1 48:50:39:00:00:00:00:00:00:00:0...

  • Page 210

    2-182 smartswitch atm switch reference manual pnninetworknode pnninetworknode use pnninetworknode to display all nodes within the pnni hierarchy as seen from a logical node on the switch. The logical node on the switch is viewed as the local node. The other nodes are viewed as remote nodes. Operator...

  • Page 211

    Smartswitch atm switch reference manual 2-183 pnninetworknode descriptions [rest. Branching] whether the remote node is able to support additional branches. Possible values are: true and false. False indicates it can support additional branches. This parameter reflects the setting of the restricted ...

  • Page 212

    2-184 smartswitch atm switch reference manual pnninetworknode examples switch_prompt # show pnninetworknode num(all) : num node id ================================================================================ 1 48:50:39:00:00:00:00:00:00:00:00:00:00:00:00:00:20:d4:14:41:ff:00 2 48:50:39:00:00:00:...

  • Page 213

    Smartswitch atm switch reference manual 2-185 pnninode pnninode use pnninode to set or display logical nodes on the switch. If the switch is represented on multiple levels of the pnni hierarchy, it has a separate logical node (and node id) for each representation. Operators add, delete, modify, show...

  • Page 214

    2-186 smartswitch atm switch reference manual pnninode descriptions [rst transit] whether or not the switch is restricted to not allowing support of svcs transiting it. Possible values are: true and false. [complex rep.] whether or not the switch uses the complex node representation. Possible values...

  • Page 215

    Smartswitch atm switch reference manual 2-187 pnninode examples switch_prompt # add pnninode nodeindex(2) : nodelevel(72) : complexrepresentation(n) : switch_prompt # switch_prompt # delete pnninode nodeindex(1) : 2 pnni node information ==============================================================...

  • Page 216

    2-188 smartswitch atm switch reference manual pnninodetimer pnninodetimer use pnninodetimer to set or display pnni protocol timer values. Operators modify, show parameters input parameter description value/field size default [nodeindex] identifier for a logical node on the switch. Positive integer 1...

  • Page 217

    Smartswitch atm switch reference manual 2-189 pnninodetimer q-Þ“Í7˜ÍiÀÜ>•r 7˜ÍiÀÜ>•ÊliÍÝii˜ÊÀiÍÀ>˜Ã“ˆÃÈœ˜ÃÊœvÊÖ˜>v† Ž˜œÝ•i`}i`Ê`>Í>l>ÃiÊÃÖ““>ÀßÊ«>vŽiÍÃ]Ê +0..ÊÀiµÖiÃÍÊ«>vŽiÍÃ]Ê>˜`Ê+0.+ð positive integer in units of seconds. 5 q+iiÀ-i•>ßi`"vŽ7˜ÍiÀÜ>•r 7˜ÍiÀÜ>•ÊliÍÝii˜ÊÍÀ>˜Ã“ˆÃÈœ˜ÃÊœvÊ`i•>ßi`Ê +0.....

  • Page 218

    2-190 smartswitch atm switch reference manual pnninodetimer descriptions [cvd pm] proportional multiplier used in algorithms that determine significant change for cdv metrics, expressed as a percentage. [ctd pm] proportional multiplier used in the algorithms that determine significant change for ctc...

  • Page 219

    Smartswitch atm switch reference manual 2-191 pnninodetimer examples switch_prompt # set pnninodetimer nodeindex(1) : 1 ptseholddown(10) : 20 helloholddown(10) : 20 hellointerval(15) : helloinactivityfactor(5) : horizontallinkinactivitytime(120) : ptserefreshinterval(1800) : ptselifetimefactor(200) ...

  • Page 220

    2-192 smartswitch atm switch reference manual pnnipeergroupid pnnipeergroupid use pnnipeergroupid to set the peer group id of a logical node on the switch. Operators modify parameters this attribute has no output parameters. Descriptions examples switch_prompt # set pnnipeergroupid nodeindex(1) : pe...

  • Page 221

    Smartswitch atm switch reference manual 2-193 pnnipglelection pnnipglelection use pnnipglelection to set or display pnni peer group election characteristics for the switch. The characteristics are with respect to a specific logical node on the switch (identified by the nodeindex input parameter). Op...

  • Page 222

    2-194 smartswitch atm switch reference manual pnnipglelection output parameter description [nodeindex] identifier of a logical node on the switch. [leadershippriority] leadership priority value of the logical node. The switch advertises this value to the peer group of that logical node. [parentnodei...

  • Page 223

    Smartswitch atm switch reference manual 2-195 pnnipglelection descriptions examples switch_prompt # modify pnnipglelection nodeindex(1) : leadershippriority(52) : parentnodeindex(2) : inittime(15) : 20 overridedelay(30) : 35 reelecttime(15) : 20 switch_prompt # switch_prompt # show pnnipglelection n...

  • Page 224

    2-196 smartswitch atm switch reference manual pnniptse pnniptse use pnniptse to display ptses stored in the topology database of the switch. Operators show parameters input parameter description value/field size default [num] index number assigned by the console that indicates which node originating...

  • Page 225

    Smartswitch atm switch reference manual 2-197 pnniptse descriptions examples switch_prompt # show pnniptse num(all) : no. Originating node id ptse count ================================================================================ 1 50:a0:39:00:00:00:00:00:00:00:00:00:14:4a:00:00:20:d4:14:4a:00:0...

  • Page 226

    2-198 smartswitch atm switch reference manual pnnireachableaddress pnnireachableaddress use pnnireachableaddress to display a list of reachable addresseses from the switch. The addresses are advertised by remote logical nodes that are visible to the switch (logical nodes from which the switch receiv...

  • Page 227

    Smartswitch atm switch reference manual 2-199 pnnireachableaddress descriptions examples switch_prompt # show pnnireachableaddress num(all) : num reachable address advertising node id ================================================================================ 1 39:00:00:00:00:00:00:00:00:00:14:...

  • Page 228

    2-200 smartswitch atm switch reference manual pnniscopemapping pnniscopemapping use pnniscopemapping to set or display the mappings of membership and connection scope from uni to pnni terms. The mappings are from the perspective of a logical node on the switch. Operators modify, show parameters inpu...

  • Page 229

    Smartswitch atm switch reference manual 2-201 pnniscopemapping [organizationplusone] highest level of pnni hierarchy (smallest pnni routing level) that lies within the uni scope value organizationplusone(9). 0-104 64 [communityminusone] highest level of pnni hierarchy (smallest pnni routing level) t...

  • Page 230

    2-202 smartswitch atm switch reference manual pnniscopemapping [intra site] highest level of pnni hierarchy (smallest pnni routing level) that lies within the uni scope value intrasite(5). [site plus one] highest level of pnni hierarchy (smallest pnni routing level) that lies within the uni scope va...

  • Page 231

    Smartswitch atm switch reference manual 2-203 pnniscopemapping descriptions operator parameters / permissions description modify pnniscopemapping [nodeindex] [localnetwork] [localnetworkplusone] [localnetworkplustwo] [siteminusone] [intrasite] [siteplusone] [organizationminusone] [intraorganization]...

  • Page 232

    2-204 smartswitch atm switch reference manual pnniscopemapping examples switch_prompt # modify pnniscopemapping nodeindex(1) : localnetwork(96) : localnetworkplusone(96) : localnetworkplustwo(96) : siteminusone(80) : intrasite(80) : siteplusone(72) : organizationminusone(72) : intraorganization(64) ...

  • Page 233

    Smartswitch atm switch reference manual 2-205 pnnistats pnnistats use pnnistats to display pnni statistics for the switch. Operators show parameters this parameter has no input parameters. Just enter show pnnistats at the switch prompt. Descriptions output parameter description [highest version] the...

  • Page 234

    2-206 smartswitch atm switch reference manual pnnistats examples switch_prompt # show pnnistats pnni base information ================================================================================ highest version : 1.0 lowest version : 1.0 dtl count originator : 0 dtl count border : 1 crankback co...

  • Page 235

    Smartswitch atm switch reference manual 2-207 pnnisummaryaddress pnnisummaryaddress use pnnisummaryaddress to manage summary address prefixes for the switch. A summary address is an abbreviation of a set of addresses, represented by an address prefix that all of the summarized addresses have in comm...

  • Page 236

    2-208 smartswitch atm switch reference manual pnnisummaryaddress descriptions [node index] identifier of a logical node on the switch. [prefix length] prefix length for the summary. [state] whether or not the summary is currently being advertised by the switch to peer group. Possible values are: act...

  • Page 237

    Smartswitch atm switch reference manual 2-209 pnnisummaryaddress examples switch_prompt # add pnnisummaryaddress nodeindex(1) : summaryaddress() : 45:00:01 prefixlength(152) : 24 summarytype(internal) : suppress(false) : switch_prompt # switch_prompt # delete pnnisummaryaddress nodeindex(1) : summar...

  • Page 238

    2-210 smartswitch atm switch reference manual pnnisvccrcc pnnisvccrcc use pnnisvccrcc to display status of the switched virtual channel connection (svcc) used by the routing control channel (rcc) of a logical node on the switch. Operators show parameters descriptions input parameter description valu...

  • Page 239

    Smartswitch atm switch reference manual 2-211 pnnisvccrcc examples switch_prompt # show pnnisvccrcc nodeindex(2) : 2 svccrccindex(all) : svcc rcc index vpi vci port rcv hellos xmt hellos hello state ================================================================================ 1 0 32 1a1 113472 11...

  • Page 240

    2-212 smartswitch atm switch reference manual pnnitnsroute pnnitnsroute use pnnitnsroute to manage routes to transit networks that are visible to the switch. Operators add, delete, show parameters input parameter description value/field size default [num] index number of the route as assigned by the...

  • Page 241

    Smartswitch atm switch reference manual 2-213 pnnitnsroute q0!.Ê0ß«ir 0À>˜ÃˆÍʘiÍÝœÀŽÊ7-ÊÍß«i°Ê+œÃÈl•iÊÜ>•ÖiÃÊ>Ài\Ê!>͈œ˜!IÍÝœÀŽ7`Ê>˜`Ê#Í…iÀ° q0!.Ê+•>˜r 0À>˜ÃˆÍʘiÍÝœÀŽÊ7-Ê«•>˜°Ê+œÃÈl•iÊÜ>•ÖiÃÊ>Ài\Ê+>ÀÀˆiÀ+œ`i7`ÊœÀÊ#Í…iÀ° q0!.Ê7-r 0À>˜ÃˆÍʘiÍÝœÀŽÊ7-°Ê q7˜`iÞr 7˜`iÞʈ˜ÍœÊÍ…iÊÃiÍÊœvÊ•ˆÃ͈˜}ÃÊœvÊvœ˜˜...

  • Page 242

    2-214 smartswitch atm switch reference manual pnnitnsroute descriptions examples switch_prompt # add pnnitnsroute portnumber() : 1a2 tnstype(nationalnetworkid) : tnsplan(carrieridcode) : tnsid() : 90:00:00:01 index(0) : routetype(exterior) : pnniscope(0) : metricstag(0) : operator parameters / permi...

  • Page 243

    Smartswitch atm switch reference manual 2-215 pnnitnsroute switch_prompt # delete pnnitnsroute tnstype(nationalnetworkid) : tnsplan(carrieridcode) : tnsid() : 39:00:00:01 index(0) : transit network route number 0 =============================================================================== node in...

  • Page 244

    2-216 smartswitch atm switch reference manual port use port to add or delete a virtual port on the switch. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you replace a tsm with another tsm of the same ...

  • Page 245

    Smartswitch atm switch reference manual 2-217 port descriptions [maxvpibits] maximum number of vpi bits. 0-6 no default [maxvcibits] maximum number of vci bits. 6-12 no default [maxsvcvpci] maximum vpcis available for svcs. 0-[2 (maxvpibits) -1] no default [minsvcvci] minimum vcis available for svcs...

  • Page 246

    2-218 smartswitch atm switch reference manual port examples switch prompt # add port portnumber() : 1a1.1 portadminstatus(up) : ilmiadminstatus(enable) : sigtype(autoconfig) : sigrole(other) : interfacetype(private) : maxvpibits(0) : maxvcibits(10) : maxsvcvpci(0) : minsvcvci(32) : maxvccs(1024) : t...

  • Page 247

    Smartswitch atm switch reference manual 2-219 portclockmode portclockmode use portclockmode to set the clock mode of a switch port. Operators modify, show parameters descriptions input parameter description value/field size default [portnumber] port number on the switch. A1 to b4 (2500 family), 1a1 ...

  • Page 248

    2-220 smartswitch atm switch reference manual portclockmode examples switch_prompt # show portclockmode portnumber(all) : port number configured mode actual mode ============================================================================== 7a1 local local 7a2 local local 7a3 local local 7a4 local l...

  • Page 249

    Smartswitch atm switch reference manual 2-221 portconfig portconfig use portconfig to manage configuration of switch ports. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you replace a tsm with another...

  • Page 250

    2-222 smartswitch atm switch reference manual portconfig note the following applies to smartswitch 6500 only: if you hot-swap a tsm with a tsm of a different type (different i/o ports), port configuration of the originial tsm is deleted. Before you insert a replacement tsm, you can display existing ...

  • Page 251

    Smartswitch atm switch reference manual 2-223 portconfig descriptions [max vpi bits] maximum number of vpi bits. Q >ÞÊ7vˆÊlˆÍÃrÊ maximum number of vci bits. Q >ÞÊ.7+Ê7«vˆrÊ maximum number of vpcis available for svcs q >ÞÊ.7+Ê7vˆrÊ maximum number of vcis available for svcs. [max vccs] maximum number ...

  • Page 252

    2-224 smartswitch atm switch reference manual portconfig examples switch_prompt # show portconfig portnumber(all) : port intf sig ilmi trans media max used oper name type type state type type bw(mbs) bw(mbs) state ============================================================================== cpu pri...

  • Page 253

    Smartswitch atm switch reference manual 2-225 portfilterset portfilterset use portfilterset to associate an atm filter set with a pair of incoming and outgoing ports. Operators add, delete, modify, show parameters . Input parameter description value/field size default [incomingport] port number on t...

  • Page 254

    2-226 smartswitch atm switch reference manual portfilterset descriptions examples switch_prompt # show atmfilterset filtername(all) : filtersetname totaladmits totaldenies referencecount ============================================================================== set1 0 0 1 switch_prompt # add por...

  • Page 255

    Smartswitch atm switch reference manual 2-227 portmode portmode use portmode to manage transmission characteristics of switch ports. Note see table 2-9 for supported i/o modules (and corresponding port types). Operators modify, show parameters in the parameter tables below, text in parenthesis indic...

  • Page 256

    2-228 smartswitch atm switch reference manual portmode descriptions [timing] (622 mbps only) enables or disables timing at the port. Timing can improve speed matching and sequencing of transmissions between the switch and network. Disabled, enabled disabled output parameter description [port id] por...

  • Page 257

    Smartswitch atm switch reference manual 2-229 portmode table 2-9 i/o module id numbers face plate number physical specification iom-21-4 155 mbps oc-3/stm-1, mmf/sc (4 port) iom-22-4 155 mbps sts-3c/stm-1, utp-5/rj-45 (4 port) iom-29-4 155 mbps oc-3/stm-1, smf-ir/sc (1 port) mmf/sc (3 port) iom-29-4...

  • Page 258

    2-230 smartswitch atm switch reference manual portmode examples switch_prompt # show portconfig portnumber(all) : port intf sig ilmi trans media max used oper name type type state type type bw(mbs) bw(mbs) state ============================================================================== 1a1 priva...

  • Page 259

    Smartswitch atm switch reference manual 2-231 portstat portstat use portstat to display or clear traffic statistics for switch ports. Operators show, clear parameters input parameter description value/field size default [portnumber] port number on the switch. A1 to b4 (2500 family), 1a1 to 8b4 (6500...

  • Page 260

    2-232 smartswitch atm switch reference manual portstat descriptions operator parameters/permissions descriptions show portstat [portnumber] portnumber> all displays atm statistics for a given port or all ports, represented in number of cells. These statistics relate to network resources management, ...

  • Page 261

    Smartswitch atm switch reference manual 2-233 portstat examples switch_prompt # show portstat portnumber(all) : port id oam rm clp1 unk vc clp1 total recvd recvd recvd dropped dropped dropped ============================================================================ 1a1 0 0 0 0 0 0 1a2 0 0 0 0 0 0...

  • Page 262

    2-234 smartswitch atm switch reference manual portstat port 2b1 statistics ============================================================================ oam cells received : 0 rm cells received : 0 clp1 cells received : 0 unknown vc cells dropped : 0 clp1 cells dropped : 0 total cells dropped : 0 por...

  • Page 263

    Smartswitch atm switch reference manual 2-235 porttrafficcongestion porttrafficcongestion use porttrafficcongestion to manage traffic congestion at switch ports. You can program the values for the minimum and maximum threshold (in number of cells) for a specified priority queue. If the number of cel...

  • Page 264

    2-236 smartswitch atm switch reference manual porttrafficcongestion descriptions [minvalue] minimum cell threshold value (in number of cells). [maxindex] index number for maximum cell threshold value. (same as the [maxindexnumber] input parameter.) [maxvalue] maximum cell threshold value (in number ...

  • Page 265

    Smartswitch atm switch reference manual 2-237 porttrafficcongestion examples switch_prompt # show porttrafficcongestion portnumber(all) : portid queueid serviceclass minindex minvalue maxindex maxvalue ============================================================================== cpu 1 cbr 10 64 15 ...

  • Page 266

    2-238 smartswitch atm switch reference manual privilege privilege use privilege to manage the privilege level of the current user. Operators show, enable, disable parameters this attribute has no output parameters. Descriptions examples switch_prompt # show privilege the current user is administrato...

  • Page 267

    Smartswitch atm switch reference manual 2-239 prompt prompt use prompt to control how the switch prompt is displayed on the console monitor. Operators modify parameters this attribute has no output parameters. Descriptions example switch_prompt # set prompt prompt(switch_prompt) : my_switch my_switc...

  • Page 268

    2-240 smartswitch atm switch reference manual pvc pvc use pvc to manage pvcs on the switch. You assign two physical or virtual ports on the switch as pvc endpoints. Note when you add the pvc, the endpoints are called port 1 and port 2 (corresponding to order of entry). For subsequent action on the p...

  • Page 269

    Smartswitch atm switch reference manual 2-241 pvc [port-1-number] number of the first port assigned to the connection. A1 to b4 (physical-2500 family), a1.N to b4.N (virtual-2500 family), 1a1 to 8b4 (physical-6500), 1a1.N to 8b4.N (virtual-6500) no default [port-1-vpci] vpci associated with port 1. ...

  • Page 270

    2-242 smartswitch atm switch reference manual pvc in the output parameter table below, ( ) indicates parameters that are available only through the show pvc /d (detailed) command. [portnumber] port number on the switch. A1 to b4 (physical-2500 family), a1.N to b4.N (virtual-2500 family), 1a1 to 8b4 ...

  • Page 271

    Smartswitch atm switch reference manual 2-243 pvc [high type] connection type from perspective of high port. [admin status] administrative status of the pvc. Possible values are: up or down. [low - high traffic decs index (tx)] index of the traffic descriptor in the direction of flow from low port t...

  • Page 272

    2-244 smartswitch atm switch reference manual pvc descriptions [cell loss ratio (low-high)] cell loss ratio in the low-to-high direction. [cumulative cell delay variation (low-high)] cumulative cell delay variation in the low-to-high direction. [max cell transfer delay (low-high)] maximum cell trans...

  • Page 273

    Smartswitch atm switch reference manual 2-245 pvc deactivate pvc [lowportnumber] [lowvpci] [lowvci] [highportid] [lowvpci] [highvci] administrator deacrivates the specified pvc. Admin status is set to down. Delete pvc [lowportnumber] [lowvpci] [lowvci] [highportid] [lowvpci] [highvci] administrator ...

  • Page 275

    Smartswitch atm switch reference manual 2-247 pvc high port : 7a3 high vpci : 0 high vci : 16 high connection type : ptp admin status : up low to high operation status : up high to low operation status : up port status : operational creation time : 0:0:0 traffic type (high-low) : cbr early packet di...

  • Page 276

    2-248 smartswitch atm switch reference manual pvcbyid pvcbyid use pvcbyid to manage a pvc by its cross-connect id. Note the following applies to smartswitch 2500 family only: you can not delete or deactivate a pvc if an ip/atm client is attached to the pvc through the ipatmpvc attribute. Operators a...

  • Page 277

    Smartswitch atm switch reference manual 2-249 pvcbyid examples switch_prompt # activate pvcbyid crossconnid() : 2 crossconnsubid() : 36 switch_prompt # switch_prompt # deactivate pvcbyid crossconnid() : 2 crossconnsubid() : 36 switch_prompt # switch_prompt # delete pvcbyid crossconnectid() : 1 cross...

  • Page 278

    2-250 smartswitch atm switch reference manual pvp pvp (smartswitch 6500 only) use pvp to manage pvps on the switch. You assign two physical ports on the switch as pvp endpoints. Note when you add the pvp, the endpoints are called port 1 and port 2 (corresponding to order of entry). For subsequent ac...

  • Page 279

    Smartswitch atm switch reference manual 2-251 pvp [port-2-number] number of the second port assigned to the connection. A1 to b4 (physical-2500 family), a1.N to b4.N (virtual-2500 family), 1a1 to 8b4 (physical-6500), 1a1.N to 8b4.N (virtual-6500) no default [port-2-vpi] vpi associated with port 2. P...

  • Page 280

    2-252 smartswitch atm switch reference manual pvp in the output parameter table below, ( ) indicates parameters that are available only through the show pvp /d (detailed) command. Output parameter description [conn id] cross-connect id of the pvp (as assigned by switch software). Each ptp pvp has a ...

  • Page 281

    Smartswitch atm switch reference manual 2-253 pvp [cell loss ratio (high-low)] cell loss ratio in the high-to-low direction. [cumulative cell delay variation (high-low)] cumulative cell delay variation in the high-to-low direction. [max cell transfer delay (high-low)] maximum cell transfer delay in ...

  • Page 282

    2-254 smartswitch atm switch reference manual pvp descriptions operator parameters / permissions description activate pvp [lowportnumber] [lowvpi] [highportid] [lowvpi] administrator activates the pvp specified. Administrative status is set to up. Add pvp [port-1-number] [port-1-vpi] [port-2-number]...

  • Page 283

    Smartswitch atm switch reference manual 2-255 pvp examples switch_prompt # add pvp conntype(ptp) : port-1-number() : 1a2 port-1-vpi() : 1 port-2-number() : 1a3 port-2-vpi() : 1 port1-to-port2trafficdescriptorindex() : 2 port2-to-port1trafficdescriptorindex() : 7 switch_prompt # show pvp portnumber(a...

  • Page 284

    2-256 smartswitch atm switch reference manual pvpbyid pvpbyid (smartswitch 6500 only) use pvpbyid to manage a pvp by its cross-connect id. Operators activate, add, deactivate, delete, show parameters this attribute has no output parameters. Descriptions input parameter description value/field size d...

  • Page 285

    Smartswitch atm switch reference manual 2-257 pvpbyid examples switch_prompt # activate pvpbyid crossconnid() : 2 crossconnsubid() : 36 switch_prompt # switch_prompt # deactivate pvpbyid crossconnid() : 2 crossconnsubid() : 36 switch_prompt # switch_prompt # delete pvpbyid crossconnectid() : 1 cross...

  • Page 286

    2-258 smartswitch atm switch reference manual reboot reboot use reboot to reboot the switch. Operators reboot parameters this attribute has no parameters. Just enter reboot at the switch prompt and the switch reboots. Descriptions example switch_prompt # reboot rebooting will temporarily disrupt all...

  • Page 287

    Smartswitch atm switch reference manual 2-259 redundancyconfigbackup redundancyconfigbackup (smartswitch 6500 only) use redundancyconfigbackup to copy switch configuration to the slave tsm/cpu backup file specified by the redundancyinfo attribute. If you use the same backup file for the slave and ma...

  • Page 288

    2-260 smartswitch atm switch reference manual redundancyinfo redundancyinfo (smartswitch 6500 only) use redundancyinfo to set or display the location of the backup configuration file for the slave tsm/cpu module. Typically, you would use the same backup file for the slave and master modules. If you ...

  • Page 289

    Smartswitch atm switch reference manual 2-261 redundancyinfo descriptions examples switch_prompt # set redundancyinfo updateconfig(n) : hostip(206.61.237.40) : 206.61.237.16 pathfilename(backup/smart6500.Ztr) : backup/slave.Ztr switch_prompt # switch_prompt # show redundancyinfo updateconfig : n hos...

  • Page 290

    2-262 smartswitch atm switch reference manual redundancyon redundancyon (smartswitch 6500 only) use redundancyon to activate support for automatic tsm/cpu redundancy. If automatic tsm/cpu redundancy is activated, the tsm/cpu slave module monitors activity of the tsm/cpu master module. Every second, ...

  • Page 291

    Smartswitch atm switch reference manual 2-263 redundancyoff redundancyoff (smartswitch 6500 only) use redundancyoff to deactivate support for automatic tsm/cpu redundancy. For a description of automatic tsm/cpu redundancy, refer to the redundancyon attribute. Note if you choose to deactivate automat...

  • Page 292

    2-264 smartswitch atm switch reference manual redundancystatus redundancystatus (smartswitch 6500 only) use redundancystatus to display status of automatic tsm/cpu redundancy and csm redundancy on the switch. Operators show parameters this attribute has no input parameters. Just type show redundancy...

  • Page 293

    Smartswitch atm switch reference manual 2-265 redundancystatus descriptions examples switch_prompt # show redundancystatus admin status : redundancy enabled oper status : system is redundant active cpu : present in slot #7 standby cpu : present in slot #8 active csm : present in slot #9 standby csm ...

  • Page 294

    2-266 smartswitch atm switch reference manual route route use route to administer ip route management to an atm client through an ethernet network. It allows network management software to communicate across a network of switches. Operators add, delete, show parameters input parameter description va...

  • Page 295

    Smartswitch atm switch reference manual 2-267 route descriptions examples switch_prompt # add route destnetip() : 204.95.77.187 gatewayip() : 204.95.77.186 switch_prompt # switch_prompt # show route route net table destination gateway flags refcnt use interface --------------------------------------...

  • Page 296

    2-268 smartswitch atm switch reference manual rows rows use rows to alter the number of rows per page on the console display. Operators modify parameters this attribute has no output parameters. Descriptions examples switch_prompt # modify rows rows(18): 25 there are now 25 rows per page switch_prom...

  • Page 297

    Smartswitch atm switch reference manual 2-269 sarstat sarstat use sarstat (segmentation and reassembly statistics) to view statistics from the sar on the cpu port. This is useful for debugging hardware problems. Operator show parameters this attribute has no input parameters. Just enter show sarstat...

  • Page 298

    2-270 smartswitch atm switch reference manual sarstat descriptions [mm int] mailbox modified indicator. [mf int] mailbox full indicator. [sbe int] system bus error indicator since last up-time or clear. [spe int] system parity error indicator since last up-time or clear. [cpe int] number of control ...

  • Page 299

    Smartswitch atm switch reference manual 2-271 sarstat examples switch_prompt # show sarstat receive statistics rcv pkts: 6 rcv byts: 648 raw cell: 0 buf uf : 0 fifo or : 0 max len : 0 len err : 0 crc err : 7 u abrts : 0 t1 err : 0 chnl dvt: 26 spur int: 0 ttal err: 7 isr int: 39 rqu int: 0 rqa int: ...

  • Page 300

    2-272 smartswitch atm switch reference manual serviceregistry serviceregistry use serviceregistry to manage entries in the service registry mib. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you repla...

  • Page 301

    Smartswitch atm switch reference manual 2-273 serviceregistry descriptions output parameter description [port] port number on the switch. (same as the [portnumber] input parameter.) [type] type of service. Possible values are: ans or lecs. [index] index identifying two services registered for the sa...

  • Page 302

    2-274 smartswitch atm switch reference manual serviceregistry examples switch_prompt # add serviceregistry portnumber(all) : a1 servicetype(lecs) : addressindex() : 1 atmaddress() : 39:00:00:00:00:00:00:00:00:00:14:1b:00:0020:d4:14:1c:00:01 switch_prompt # switch_prompt # delete serviceregistry port...

  • Page 303

    Smartswitch atm switch reference manual 2-275 shutdown shutdown use shutdown to shut down the switch to a state where it can be powered off. Shutdown stops all logging and synchronizes the file system. You must enter shutdown before turning off the switch. Operator shutdown parameters this attribute...

  • Page 304

    2-276 smartswitch atm switch reference manual sigstatistics sigstatistics use sigstatistics to display signaling statistics of a port. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you replace a tsm w...

  • Page 305

    Smartswitch atm switch reference manual 2-277 sigstatistics description [detect unavailable resources] !Ö“liÀÊœvÊv>••ÃÊÀi•ivÍi`Êliv>ÖÃiÊœvÊÖ˜>Ü>ˆ•>l•iÊÀiÃœÖÀviÃÊœ˜ÊœÍ…iÀÊÃ݈Ív…ið [emit unavailable resources] !Ö“liÀÊœvÊv>••ÃÊÀi•ivÍi`Êliv>ÖÃiÊœvÊÖ˜>Ü>ˆ•>l•iÊÀiÃœÖÀviÃÊœ˜ÊÍ…ˆÃÊÃ݈Ív…° [detect called pa...

  • Page 306

    2-278 smartswitch atm switch reference manual sigstatistics examples switch_prompt # show sigstatistics executing this command : show sigstatistics portnumber(all) : 1a1 ================================================ signalling statistics ================================================ port# : 1a...

  • Page 307

    Smartswitch atm switch reference manual 2-279 sigtimer sigtimer use sigtimer to set or display signaling timer values for a port note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you replace a tsm with an...

  • Page 308

    2-280 smartswitch atm switch reference manual sigtimer descriptions examples switch_prompt # show sigtimer portnumber() : 1a1 ============================================ : all timer values in milliseconds phy_port_id : 1a1 t301 duration : 180000 t303 duration : 4000 t303 retries : 1 t306 duration :...

  • Page 309

    Smartswitch atm switch reference manual 2-281 slotconfig slotconfig use slotconfig to display configuration of slots in the switch chassis (to see which slots are occupied by tsm or csm modules). You also can get specific information about each module. Operators show parameters descriptions input pa...

  • Page 310

    2-282 smartswitch atm switch reference manual slotconfig examples switch_prompt # show slotconfig slot(all) : slot id board io modules ============================================================================== 7 tsm 2 9 csm na switch_prompt # show slotconfig slot(all) : 7 slot 7 ================...

  • Page 311

    Smartswitch atm switch reference manual 2-283 spvc spvc use spvc to add, delete, or show soft pvcs (spvcs) on the switch. An spvc connects this switch (the source switch) to a switch across the atm network (the target switch). Note before adding an spvc at this switch, you must configure the target ...

  • Page 312

    2-284 smartswitch atm switch reference manual spvc in the output parameter table below, ( ) appears next to parameters that are available only through the show spvc /d (detailed) command [backwardtrafficdescriptor index] index of the backward (target to source) traffic descriptor. [retryinterval] ti...

  • Page 313

    Smartswitch atm switch reference manual 2-285 spvc descriptions [retry threshold] number of consecutive failed setup attempts for a particular spvc before the spvcccallfailures object is incremented. [retry failures] number of failed retry attempts. [retry limit] maximum number of spvc retries. [tra...

  • Page 314

    2-286 smartswitch atm switch reference manual spvc table 2-10 spvc failure cause codes code description 1 unallocated (unassigned) number. 2 no route to specified transit network. 3 no route to destination. 16 normal call clearing. 17 user busy. 18 no user responding. 21 call rejected. 22 number cha...

  • Page 315

    Smartswitch atm switch reference manual 2-287 spvc 81 invalid call reference value. 82 identified channel does not exist. 88 incompatible destination. 89 invalid endpoint reference. 91 invalid transit network selection. 92 too many pending add party requests. 96 mandatory information element is miss...

  • Page 316

    2-288 smartswitch atm switch reference manual spvc examples switch_prompt # show spvc portnumber(all) : sourcevpi(0) : sourcevci(32) : ============================================== port src vpi src vci operation status ============================================== total number of spvcs = 0 switch_...

  • Page 317

    Smartswitch atm switch reference manual 2-289 spvc switch_prompt # delete spvc portnumber() : 5a2 sourcevpi(0) : 0 sourcevci(32) : 100 deleted spvc successfully. Switch_prompt # switch_prompt # show spvc portnumber(all) : sourcevpi(0) : sourcevci(32) : ============================================== ...

  • Page 318

    2-290 smartswitch atm switch reference manual spvcaddress spvcaddress use spvcaddress to configure a target address on the switch. The target address allows the switch to act as the target switch in an spvc or spvp connection. The spvc or spvp is established (added) at the source switch. Operators a...

  • Page 319

    Smartswitch atm switch reference manual 2-291 spvcaddress examples switch_prompt # show spvcaddress executing this command : show spvcaddress portnumber(all) : targetaddress() : port spvc target address ================================================================================ a1 39:00:00:00:0...

  • Page 320

    2-292 smartswitch atm switch reference manual spvcbase spvcbase use spvcbase to display status information about spvcs and spvps on the switch. Operators show parameters this attribute has no input parameters. Just type spvcbase at the switch prompt. Descriptions output parameter description [curren...

  • Page 321

    Smartswitch atm switch reference manual 2-293 spvcbase examples switch_prompt # show spvcbase ============================================================ currently currently spvc call notify failure failing spvc failing spvp failures interval trap enable ============================================...

  • Page 322

    2-294 smartswitch atm switch reference manual spvccallfailurestrapenable spvccallfailurestrapenable use spvccallfailurestrapenable to enable or disable the generation of traps related to spvc or spvp call failures. Operators modify parameters this attribute has no output parameters descriptions exam...

  • Page 323

    Smartswitch atm switch reference manual 2-295 spvcfailed spvcfailed use spvcfailed to display failed spvcs on the switch. An spvc fails when its call setup request is rejected by the target switch. The spvc call request is sent from this switch (the source switch) to the target switch. Note use the ...

  • Page 324

    2-296 smartswitch atm switch reference manual spvcfailed descriptions examples switch_prompt # show spvcfailed executing this command : show spvcfailed portnumber(all) : sourcevpi(0) : sourcevci(32) : ========================================================== port src vpi src vci curr.Fail-time-stam...

  • Page 325

    Smartswitch atm switch reference manual 2-297 spvcnotifyinterval spvcnotifyinterval use spvcnotifyinterval to set the minimum elapsed time between successive traps that indicate a call failure. Operators modify parameters this attribute has no output parameters. Descriptions examples switch_prompt #...

  • Page 326

    2-298 smartswitch atm switch reference manual spvcrestart spvcrestart use spvcrestart to restart a failed spvc on the switch. An spvc fails when its call setup request is rejected by the target switch. The spvc call request is sent from this switch (the source switch) to the target switch. Spvcresta...

  • Page 327

    Smartswitch atm switch reference manual 2-299 spvctarget spvctarget use spvctarget to display spvc target information on the switch. Information is displayed only if the switch is the destination (target) of an spvc. The spvc is established (added) at a source switch across the atm network. Operator...

  • Page 328

    2-300 smartswitch atm switch reference manual spvctarget examples switch_prompt # show spvctarget portnumber(all) : 7b3 port target address vpci vci ============================================================================= 7b3 11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11 0 101 ope...

  • Page 329

    Smartswitch atm switch reference manual 2-301 spvp spvp (smartswitch 6500 only) use spvp to add, delete, or show soft pvps (spvps) on the switch. An spvp connects this switch (the source switch) to a switch across the atm network (the target switch). Note before adding an spvp at this switch, you mu...

  • Page 330

    2-302 smartswitch atm switch reference manual spvp in the output parameter table below, ( ) appears next to parameters that are available only through the show spvp /d (detailed) command [retrylimit] maximum number of spvp retries. 0-65535 [retrythreshold] number of consecutive failed setup attempts...

  • Page 331

    Smartswitch atm switch reference manual 2-303 spvp descriptions [traffic type (backward)] type of traffic in the backward (target to source) direction. [forward trafffic descriptor index] index of the forward (source to target) traffic descriptor. [backward traffic descriptor index] index of the bac...

  • Page 332

    2-304 smartswitch atm switch reference manual spvp 21 call rejected. 22 number changed. 23 user rejects all calls with calling line identification (clid) restriction. 27 destination out-of-order. 28 invalid number format (address incomplete). 30 response to status enquiry. 31 normal, unspecified. 34...

  • Page 333

    Smartswitch atm switch reference manual 2-305 spvp examples switch_prompt # show spvp portnumber(all) : sourcevpi(0) : sourcevci(32) : =================================== port src vpi operation status =================================== total number of spvps = 0 switch_prompt# add spvp portnumber() ...

  • Page 334

    2-306 smartswitch atm switch reference manual spvp switch_prompt # show spvp /d portnumber(all) : 5a2 sourcevpi(0) : 0 port : 5a2 source vpi : 0 target address : 11:11:11:11:11:11:11:11:11:11:11:11:11:11:11 :11:11:11:11:11 target vpi : 0 last release cause : 0 operation status : connected retry inte...

  • Page 335

    Smartswitch atm switch reference manual 2-307 spvpfailed spvpfailed (smartswitch 6500 only) use spvpfailed to display failed spvps on the switch. An spvp fails when its call setup request is rejected by the target switch. The spvp call request is sent from this switch (the source switch) to the targ...

  • Page 336

    2-308 smartswitch atm switch reference manual spvpfailed examples switch_prompt # show spvpfailed executing this command : show spvpfailed portnumber(all) : sourcevpi(0) : ========================================================== port src vpi curr.Fail-time-stamp (hr:min:sec) ======================...

  • Page 337

    Smartswitch atm switch reference manual 2-309 spvprestart spvprestart (smartswitch 6500 only) use spvprestart to restart a failed spvp on the switch. An spvp fails when its call setup request is rejected by the target switch. The spvp call request is sent from this switch (the source switch) to the ...

  • Page 338

    2-310 smartswitch atm switch reference manual spvprestart examples switch_prompt # modify spvprestart executing this command : set spvprestart portnumber(all) : a1 sourcevpi(0) : 1 leafreference(1) : 1.

  • Page 339

    Smartswitch atm switch reference manual 2-311 spvptarget spvptarget (smartswitch 6500 only) use spvptarget to display spvp target information on the switch. Information is displayed only if the switch is the destination (target) of an spvp. The spvp is established (added) at a source switch across t...

  • Page 340

    2-312 smartswitch atm switch reference manual spvptarget examples switch_prompt # show spvptarget portnumber(all) : 7b3 port target address vpci ============================================================================= 7b3 11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11:11 0 operstatus ...

  • Page 341

    Smartswitch atm switch reference manual 2-313 sscopconfig sscopconfig use sscopconfig to set or display switch service-specific connection-oriented protocol parameters. Sscop parameters control how the switch interoperates with other switches. Note the following applies to smartswitch 6500 only: you...

  • Page 342

    2-314 smartswitch atm switch reference manual sscopconfig [keepalivetime] rate of pollstat exchange (in milliseconds) in the absence of sd pdu traffic. 1000-2000 2000 [noresponsetime] maximum time (in milliseconds) within which a poll must be acknowledged by a stat pdu. 10000-15000 7000 [cctime] rat...

  • Page 343

    Smartswitch atm switch reference manual 2-315 sscopconfig descriptions examples switch_prompt # modify sscopconfig portid (1a1) : 1b1 maxpd(10) : 15 maxcc(4) : 5 polltime(200) : 250 keepalivetime(1000) : 1500 noresponsetime(10000) : 15000 cctime(1000) : 1500 rxwindowsz(256) : 256 switch_prompt # swi...

  • Page 344

    2-316 smartswitch atm switch reference manual sscopstatistics sscopstatistics use sscopstatistics to display sscop statistics of a port or all ports. Note the following applies to smartswitch 6500 only: you can hot-swap tsms. Hot-swapping is replacing a module when the chassis is powered up. If you ...

  • Page 345

    Smartswitch atm switch reference manual 2-317 sscopstatistics [num begin rej transmitted] number of beginreject pdus transmitted. [num begin rej received] number of beginreject pdus received. [num resync transmitted] number of resync pdus transmitted. [num resync received] number of resync pdus rece...

  • Page 346

    2-318 smartswitch atm switch reference manual sscopstatistics description [num stat transmitted] number of stat pdus transmitted. [num stat received] number of stat pdus received. [num ustat transmitted] number of ustat pdus transmitted. [num ustat received] number of ustat pdus received. [num sd tr...

  • Page 347

    Smartswitch atm switch reference manual 2-319 sscopstatistics examples switch_prompt # show sscopstatistics portid(all) : 1a2 ================================================ sscop statistics ================================================ port# : 1a2 no of begin transmitted : 1 no of begin receive...

  • Page 348

    2-320 smartswitch atm switch reference manual svc svc use svc to display svcs on a port or all ports. Operator show parameters input parameter description value/field size default [portnumber] port number on the switch. You can specify a physical or virtual port. A1 to b4 (physical-2500 family), a1....

  • Page 350

    2-322 smartswitch atm switch reference manual svcbyid svcbyid use svcbyid to display a single or all svcs in normal or detail mode. Operator show parameters in the output parameter table below, ( ) indicates parameters that are available only through the show svdbyid /d (detailed) command input para...

  • Page 351

    Smartswitch atm switch reference manual 2-323 svcbyid descriptions [operation status] operational status (up or down). [early packet discard] early packet discard for the cross connect as calculated by cac. [high port] port receiving the forward traffic flow of the high/low pair. [cell loss ratio] c...

  • Page 353

    Smartswitch atm switch reference manual 2-325 switch switch use switch to backup or restore the switch configuration file. Operators backup, restore parameters this attribute has no output parameters. Input parameter description value/field size default [serverip] ip address of the backup server. Do...

  • Page 354

    2-326 smartswitch atm switch reference manual switch descriptions examples switch_prompt # backup switch serverip(1.1.1.200) : 1.1.1.200 path(public/smartcell.Ztr) : /back_dir/cnfg_wk04 switch_prompt # switch_prompt # restore switch serverip() : 1.1.1.200 path(/back_dir/cnfg_wk04) : backup file is v...

  • Page 355

    Smartswitch atm switch reference manual 2-327 switchconfig switchconfig use switchconfig to manage switch-related parameters, such as switchname and ip address. Operators modify, show parameters input parameter description value/field size default [switchname] name of the switch. 1-19 characters swi...

  • Page 356

    2-328 smartswitch atm switch reference manual switchconfig descriptions [number of tsm boards] number of tsm modules installed in the chassis. [active cpu model] model of the active cpu (up to 7 characters). [active cpu speed] speed of the active cpu. [active cpu board id] id number of the active cp...

  • Page 357

    Smartswitch atm switch reference manual 2-329 switchconfig examples switch_prompt # modify switchconfig switchname(switch_1) : switch_2 ipaddress(200.30.72.122) : 1.1.1.202 ipnetmask(255.255.255.0) : 255.255.255.128 switch_prompt # switch_prompt # show switchconfig switch configuration =============...

  • Page 358

    2-330 smartswitch atm switch reference manual switchname switchname use switchname to change the name of the switch. Operators modify parameters this attribute has no output parameters. Descriptions examples switch_prompt # modify switchname switchname(switch_1): switch_2 switch_prompt # input param...

  • Page 359

    Smartswitch atm switch reference manual 2-331 switchtrafficcongestion switchtrafficcongestion use switchtrafficcongestion to manage global switch traffic congestion thresholds on the switch. Operators modify, show parameters parameter description value/field size default [lowepdwatermark threshold (...

  • Page 360

    2-332 smartswitch atm switch reference manual switchtrafficcongestion descriptions examples switch_prompt # modify switchtrafficcongestion lowepdwatermark(10922) :20971 highepdwatermark(21845) :10485 clp1_discardwatermark(13072) :13107 rmcellmarkingenable(disable) : explicitratemarkingenable(disable...

  • Page 361

    Smartswitch atm switch reference manual 2-333 trafficdescriptor trafficdescriptor use trafficdescriptor to manage traffic types. Operators add, delete, show parameters input parameter description value/field size default [traffictype] service category supported. Cbr, ubr, rtvbr, nrtvbr, abr ubr [tra...

  • Page 362

    2-334 smartswitch atm switch reference manual trafficdescriptor [scrclp0] sustainable cell rate clp = 0 (kilobits per second). Zero or positive integer 0 [mbsclp0+1] maximum burst size clp = 0+1 (kilobits). Zero or positive integer 0 [mbsclp0] maximum burst size clp = 0 (kilobits ). Zero or positive...

  • Page 363

    Smartswitch atm switch reference manual 2-335 trafficdescriptor descriptions [peak cell rate clp_0+1] peak cell rate clp=0+1 (in kilobits per second). [sust cell rate clp_0] sustainable cell rate clp=0 (in kilobits per second). [sust cell rate clp_0+1] sustainable cell rate clp=0+1 (in kilobits per ...

  • Page 364

    2-336 smartswitch atm switch reference manual trafficdescriptor examples switch_prompt # add trafficdescriptor executing this command : add trafficdescriptor traffictype(ubr) : cbr trafficdescriptortype(2) : 2 pcrclp01(100) : 200 pcrclp0(0) : 200 scrclp01(0) : 200 scrclp0(0) : 200 mbsclp01(0) : 200 ...

  • Page 365

    Smartswitch atm switch reference manual 2-337 trapcommunity trapcommunity use trapcommunity to manage the list of hosts that the switch sends trap notifications to concerning significant events. Each trap community has a name, ip address, and port number. The trap community name and address combinat...

  • Page 366

    2-338 smartswitch atm switch reference manual trapcommunity examples switch_prompt # add trapcommunity name() : boris ipaddr() : 204.95.77.148 port (162) : 100 switch_prompt # switch_prompt # show trapcommunity trapcommunity name ip address port ======================================================...

  • Page 367

    Smartswitch atm switch reference manual 2-339 trustednms trustednms use trustednms to configure a trusted network management system (nms) on the switch. The trusted nms is identified by its ip address. The trusted network management system is the only nms allowed to perform critical operations such ...

  • Page 368

    2-340 smartswitch atm switch reference manual trustednms examples switch_prompt # modify trustednms ipaddr(0.0.0.0) : 90.1.1.1 trusted nms ip-address : 90.1.1.1 switch_prompt # switch_prompt # show trustednms trusted nms ip-address : 90.1.1.1 switch_prompt #.

  • Page 369

    Smartswitch atm switch reference manual 3-1 3 boot load commands this chapter describes the low-level boot load commands. Boot load commands are used for setting switch start-up behavior and for performing software downloads. Use the boot load commands to: • set which copy of the boot load software ...

  • Page 370

    3-2 smartswitch atm switch reference manual chpi command boot load commands chpi command use chpi to set one of the two boot load software images as the default. Unless otherwise specified within the initial reboot countdown, the default boot load software image is the image that is loaded into dram...

  • Page 371

    Smartswitch atm switch reference manual 3-3 boot load commands dcfg command dcfg command use dcfg to display information about the current boot prom configuration • revision numbers of both boot load software images • display the switch mac address • number (in hexadecimal) of contiguous mac address...

  • Page 372

    3-4 smartswitch atm switch reference manual go command boot load commands examples =>df s you've requested a switch software download are you sure?(y/n)y initializing ethernet... Starting bootp... Boot file: c:\tftpboot\switch.Ima using tftp to get bootfile "c:\tftpboot\switch.Ima" . ..................

  • Page 373

    Smartswitch atm switch reference manual 3-5 boot load commands he command examples =>go s bypassing post verifying checksum of switch software... Attaching network interface ei0... Done. Attaching network interface lo0... Done. 0xe054f600 (troottask): flashfslib: initialized initializing flash file-...

  • Page 374

    3-6 smartswitch atm switch reference manual ponf command boot load commands ponf command use ponf to set whether post diagnostics are run by default when the switch is started. Examples =>ponf p modifying control/stat field to execute post, please wait... New postonoff value programmed successfully ...

  • Page 375

    Smartswitch atm switch reference manual 3-7 boot load commands swms command swms command use swms to tell the switch to transfer tsm/cpu mastership to the redundant cpu/tsm. Examples =>swms transferring mastership to slave tsm/cpu... =>.

  • Page 376

    3-8 smartswitch atm switch reference manual swms command boot load commands.

  • Page 377

    Smartswitch atm switch reference manual a-1 appendix a acronyms a b aal atm adaptation layer aal1 atm adaptation layer type 1 aal2 atm adapter layer type 2 aal3/4 atm adapter layer type 3/4 aal5 atm adapter layer type 5 aalm atm adaptation layer mux abr available bit rate afi authority and format id...

  • Page 378

    A-2 smartswitch atm switch reference manual acronyms c bootp boot protocol bus broadcast and unknown server cac call admission control can campus area network cat-3 category 3 unshielded twisted pair cable cat-5 category 5 unshielded twisted pair cable cbr constant bit rate ccitt comite consultatif ...

  • Page 379

    Smartswitch atm switch reference manual a-3 acronyms d e dcc digital cross connect, generic dacs or direct connect card, data interface module df download flash ds-0 digital signaling 0 ds-1 digital signaling 1 ds-3 digital signaling 3 dte data terminal equipment dtl designated transit list dvt dela...

  • Page 380

    A-4 smartswitch atm switch reference manual acronyms f g h i fcs frame check sequence fifo first in first out ftp file transfer protocol gb/s gigabits per second gcac generic call admission control gcra generic cell rate algorithm gfc generic flow control hec header error check ieee institute of ele...

  • Page 381

    Smartswitch atm switch reference manual a-5 acronyms j k l ilmi integrated local management interface i/o input/output iom input/output module ip internet protocol ip/atm internet protocol over atm ipx internetwork packet exchange protocol itu-tss international telecommunications union-telecommunica...

  • Page 382

    A-6 smartswitch atm switch reference manual acronyms m n les lane server leselan lane server emulated lan lis logical ip subnetwork llc logical link control lmi local management interface lnni lan emulation network to network interface mac media access control man metropolitan area network mb/s mega...

  • Page 383

    Smartswitch atm switch reference manual a-7 acronyms o p netbeui netbios extension user interface nfs network file system nic network interface controller/card nls natural language syntax nms network management system nni network node interface or network-to-network interface nrt-vbr non real time -...

  • Page 384

    A-8 smartswitch atm switch reference manual acronyms q r pdu protocol data unit pgl peer group leader pmd physical media dependent sub-layer pmp point-to-multipoint p-nni private network node interface or private network-to-network interface ppd partial packet discard prom programmable read-only mem...

  • Page 385

    Smartswitch atm switch reference manual a-9 acronyms s rm resource management rma return merchandise authorization rqu receive queue underrun rs-# recommended standard defined by electronic industries association rt-vbr real time - variable bit rate rw read-write access saal signaling atm adaptation...

  • Page 386

    A-10 smartswitch atm switch reference manual acronyms t u svc switched virtual circuit svcc switched virtual channel connection t-1 transmission system 1 t-3 transmission system 3 taxi transparent asynchronous transmitter/receiver interface tcp transmission control protocol td traffic descriptor tdm...

  • Page 387

    Smartswitch atm switch reference manual a-11 acronyms v w vbr/rt variable bit rate/real time vbr/nrt variable bit rate/non-real time vc virtual circuit vcc virtual channel connection vci virtual channel identifier vcl virtual channel link vlan virtual lan vp virtual path vpc virtual path connection ...

  • Page 388

    A-12 smartswitch atm switch reference manual acronyms.

  • Page 389

    Smartswitch atm switch reference manual b-1 appendix b event/alarm messages the smartswitch 2500 family and smartswitch 6500 record and report their operation in real-time using events and alarms. An event is the occurrence of a significant activity. Examples of events are a port going down or a cli...

  • Page 390

    B-2 smartswitch atm switch reference manual event/alarm messages the display provides the following information: u message index number — display sequence number assigned by the console. U event id — unique id assigned to each event type at the factory. U message text — description of the event. U s...

  • Page 391

    Smartswitch atm switch reference manual b-3 event/alarm messages for example, the following event originates from the signaling module. 1 117571585 minor event 000:00:23:502 --------------------------------------------------- saal connection has become active, initiated locally port id 0x00000002 pr...

  • Page 392

    B-4 smartswitch atm switch reference manual event/alarm messages.

  • Page 393

    Smartswitch atm switch reference manual c-1 appendix c technical support this appendix tells you what to do if you need technical support for your switch. Cabletron offers several support and service programs that provide high-quality support to our customers. For technical support, first contact yo...

  • Page 394

    C-2 smartswitch atm switch reference manual hardware warranty technical support hardware warranty cabletron warrants its products against defects in the physical product for one year from the date of receipt by the end user (as shown by proof of purchase). A product that is determined to be defectiv...

  • Page 395

    Smartswitch atm switch reference manual index-1 index numerics 622loopback attribute ............................. 2-1 a abbreviations, description of .................... 1-3 accessing the boot load prompt ................ 3-1 activating a pvc ..................................2-240 , 2-248 a pvp ....

  • Page 396

    Index-2 smartswitch atm switch reference manual index broadcast and unknown server (bus) (cont.) starting of ....................................... 2-129 statistics for ...................................... 2-30 stopping of ..................................... 2-129 bus client, statistics for ......

  • Page 397

    Smartswitch atm switch reference manual index-3 index deleting (cont.) an les from an elan .................. 2-133 atm filter from a port ................... 2-225 bus clients ...................................... 2-20 clients registered with les ............ 2-131 elan entries at the lecs ..........

  • Page 398

    Index-4 smartswitch atm switch reference manual index ip/atm vlan arp server table for ........................ 2-82 creation of ........................................ 2-83 ipaddress attribute ................................. 2-81 ipatmarp attribute ............................. 2-82 ipatmclient ...

  • Page 399

    Smartswitch atm switch reference manual index-5 index modifying (cont.) cac statistics .................................. 2-42 call failure trap interval .................. 2-297 console timeout ................................ 2-59 core dump settings ........................... 2-60 elan entries at...

  • Page 400

    Index-6 smartswitch atm switch reference manual index port bandwidth allocation for .................. 2-37 cac statistics for ............................. 2-35 port attribute ......................................... 2-216 portclockmode attribute ...................... 2-219 portconfig attribute ....

  • Page 401

    Smartswitch atm switch reference manual index-7 index showing (cont.) failed soft pvcs ............................. 2-295 failed soft pvps ............................. 2-307 global traffic parameters, switch ... 2-331 ilmi functions ................................. 2-78 information les/bus vccs ....

  • Page 402

    Index-8 smartswitch atm switch reference manual index spvcnotifyinterval attribute ................. 2-297 spvcrestart attribute ............................ 2-298 spvctarget attribute ............................. 2-299 spvp attribute ....................................... 2-301 spvpfailed attribu...