CAD Audio VX2 Information - page 4
VX2 Specifications:
Type:
Side address, multi-pattern true condenser. Dual tube electronics.
Frequency Response:
10-20 kHz.
Polar Patterns:
Cardioid, Figure eight, Omnidirectional .
Impedance:
Low (200 ohms nominal).
Output Level At 1 kHz.:
Open Circuit Voltage:
-55 dB (0 dB = 1 volt per microbar).
17.8 mV/Pascal.
Dynamic Range:
116 dB (Noise floor to max SPL @ less than 0.5% THD).
123 dB (Noise floor to max SPL @ less than 5.0% THD).
Equivalent Noise Level:
13 dB Equivalent SPL, A weighted, cardioid.
Maximum Output Level:
+10.0 dBV (@ 136 dB SPL, less than 5.0% THD).
Maximum SPL:
145 dB SPL (With 16 dB pad, less than 0.5% THD ).
152 dB SPL (With 16 dB pad, less than 5.0% THD ).
Total Harmonic Distortion:
Less than 0.5% @ 129dB SPL without pad.
Less than 5.0% @ 136 dB SPL without pad.
Signal-To-Noise Ratio:
81 dB (At 94 dB SPL).
Capsule Capacitance:
60 pF.
Powering:
Included VX2 analog power supply.
Connector:
7 pin XLR, microphone.
3 pin XLR, audio out from power supply.
Cable:
Professional quality 7 conductor, 30 ft. long.
Finish:
Matte blue housing, nickel plated screen assembly.
Dimensions (Microphone):
2.42" x 2.87" x 9.2" long.
Dimensions (VX2PS Power Supply):
8.370 (212.60mm)W x 1.715 (43.56mm)H x 7.250 (184.15mm)L.
Net Weight (Microphone):
30 oz. (850 grams).
Net Weight (VX2PS Power Supply):
3lb, 9 oz. (1615 grams).
Included Accessories:
ZM-2 ....... External shock mount.
30 ft. professional quality 7 conductor cable with gold plated XLR male and female
connectors.
Rugged carrying case.
Optional Accessories:
VX2 digital output module.
Optional Digital Interface
Preliminary Specifications:
NOTE: Specifications for the Digital Interface may change to conform to standards
established by the A.E.S.S.C. committee on digital microphones.
The optional digital interface mounts in the VX2 power supply and can be field
installed. Features include:
24 Bit resolution.
Adjustable sample rates of 96kHz, 48kHz, 44.1kHz and 32kHz.
120 dB dynamic range (A weighted).
Low noise and distortion (>105 dB THD + noise).
Differential analog architecture.
Linear phase digital anti-alias filtering.
Unique psychoacoustic noise shaping filter which subjectively truncates
the output to 16, 18, or 20 bits while 24 bit sound quality is preserved.
LED VU meter.
Fully transformer isolated.
AES/EUB or S/PDIF format.
XLR and RCA output connectors.
CAD 341 Harbor St. Conneaut, OH 44030 (440) 593-1111 Fax (440) 593-5395
Professional Microphones
TWO-YEAR LIMITED WARRANTY
CTI Audio, Inc. (CAD) hereby warrants that this product will be free of defects in
material and workmanship for a period of two years from the date of purchase. In the
unlikely event a defect occurs CAD will, at its option, either repair or replace with a
new unit of equal or greater value. You should retain proof of purchase to validate the
purchase date and return it with any warranty claim. Return warranty claims carefully
packed, insured and prepaid to the Service Department at the address listed below.
This warranty excludes exterior finish or appearance, damage from abuse, misuse of
the product, use contrary to CADs instructions or unauthorized repair. All implied
warranties or merchantability or fitness for a particular purpose are hereby disclaimed
and CAD hereby disclaims liability for incidental, special or consequential damages
resulting from the use or unavailability of this product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state. Some states do not allow the exclusion or limitation of inciden-
tal or consequential damages or limitations on how long an implied warranty lasts, so
the above exclusions and limitations may not apply to you.
Note: No other warranty, written or oral is authorized by CTI Audio, Inc.
Optional Digital Output Module
The optional digital output module installs in the front of the VX2 power supply. Preliminary specifications for this module appear on the following page. See
the installation instructions included with the module before removing the over panel on the front of the power supply. Contact CAD sales for price and
availability of the digital output module.