User instructions assembly instructions patio living 503-0061 lev2 please note: your product may differ from the image on the front cover please note: your product may differ from the image on the front cover meridian 3 with side burner meridian 4 with side burner 98500 98501 0063/09 pin: 0063bu7867...
Cadac europe ratio 26, 6921 rw duiven, the netherlands tel: +31 26 319 7740 . Fax: +31 26 319 7743 . Email: info@cadaceurope.Nl website: www.Cadaceurope.Com cadac uk cadac germany cadac france cadac scandinavia cadac south east europe cadac australia cadac north america cadac middle east cadac zambi...
Gb part no. Description photo qty 1 warming rack 1 2 side burner assembly 1 3 side table 1 4 bottom panel 1 5 bottom beam 1 6 wheel 2 7 wheel cap 2 8 wheel axle 2.
9 back panel 1 10 door beam 1 11 drip bowl 1 12 drip pan 1 13 flame tamer 3 14 large grids (265mm) 1 15 right door 1 16 left door 1 17 dome & burner box 1.
18 castor 2 19 right side panel 1 20 left side panel 1 21 fire box 2 22 seperation panel 1 23 drip pan handle 1 24 small grids (105mm) 1 25 grill plate 1.
Hardware a m6*16 bolt 4pcs b m6*12 bolt 16pcs c door pin 2pcs d φ10 washer 2pcs e φ6 elastic washer 18pcs f φ10 elastic washer 2pcs g φ6 washer 20pcs h specific screw 4pcs i ve washer 4pcs j st3.9*10 self-tapping screw 4pcs k m4*10 bolt 4pcs l φ4 elastic washer 4pcs m φ4 washer 4pcs.
Step 1: screw the two castors(18) onto right side panel(19) step 2: use the m6*12 bolt (b), through the φ6 spring washer (e), φ6 washer (g) to join the back panel (9) and side panels (19,20)..
Step 3: push axle (8) through the wheel (6), φ10 spring washer (f), φ10 washer(d) and hole on the left side panel (20). Screw it onto the weld-nut and clip on the wheel cap (7). Step 4: push the m6*12 bolt (b) through the φ6 spring washer (e), φ6 washer (g) and fix bottom beam (5) to the two side pa...
Step 5: push the m6*12 bolt (b) through the φ6 spring washer (e), φ6 washer (g) and fix the bottom panel (4) in position by screwing it into the riv-nuts on the side panels. Step 6: use the m6*12 bolts, Ø6 spring washers and Ø6 washers to fix the door beam(10) to the frame by screwing it onto the si...
Step 7: align the slots in the brackets underneath the side tray with the studs in the right hand side panel (19). Push the bracket inwards, just enough to clear the studs, and clip the bracket onto the studs. Step 8: to fix the side burner assembly (2) to the left side panel (20), take screw (h) an...
Step 9: use the st9*10 self-tapping screws (j) to fix the top plate (22) in place. Ensure the cut-outs face forward as shown below. Step 10: place the dome & burner assembly (17) onto the frame assembly and use the m6*16 bolts (a) and vitreous enameled washers (i) to fix the dome & burner assembly (...
Step 11: route the flexible hose underneath the side burner through the hole situated at the back of the left side panel (20). Connect the side burner flexible hose connection to the burner box inlet fitting situated at the rear of the burner box, see the below diagram. Use a spanner to tighten the ...
Step 12: fit the fire boxes (21) to the bbq and bend the tags underneath the fire boxes over to permanently fix it in place. Zoom view step 13: place a flame tamer (13) over each burner..
Step 14: place the grids, grill plates and warming rack into the bbq as shown below. Step 15: fit the drip pan handle (23) onto the drip pan (12) by sing the m4*10 bolts (k), Ø4 spring washer and Ø4 washer supplied. Refer to the below diagram..
Step 16: align the pin underneath the right hand door (15) with the corresponding hole on the bottom beam assemble the door in place by aligning the hole on top of the door with the corresponding hole on the beam and push the door pin (c) into the hole. Assemble the left hand door (16) the same way....
Step 18: hang the drip bowl (11) onto the drip pan (12) as shown below..
