Summary of Momentum CSA SERIES
Page 1
Csa series amplifier //owners manual.
Page 3
Features 2 thank you for purchasing this cadence momentum csa series amplifier. Over the years, the technology used to create audio amplifiers has grown by leaps and bounds. We have tens of thousands of satisfied customers still using our first generation ultra drive amplifiers which are more than 1...
Page 4
2 3 installation battery voltage: cadence momentum csa amplifiers are rated and regulated to 14.4 volts and below. Maximum input voltage is 16 volts while the minimum voltage is 12 volts. *** do not exceed 16 input voltage. *** protection circuitry: cadence amplifiers incorporate many outstanding pr...
Page 5
Features 3 4 the wire harness should be made of red primary cable of at least 8 gauge for the csa1000.2 and at least 4 gauge for all other larger models. The harness should terminate in a large ring terminal for connection directly to the positive terminal of the car battery. Use a spade plug to att...
Page 6
Power / ground / remote wiring diagram 5 power input gnd 4 ohm bridged ch1c h2 ch3 ch3 ch4 bridged 4 ohm ch4 rem+ 12v fuses battery fuse fuse ground remote turn on terminal of head unit fm 2 93.3 stereo loud.
Page 7
6 mounting the amplifier: choose a convenient mounting location with unobstructed airflow. The momentum csa series amplifiers feature four mounting tabs located near the amplifiers four corners. Using the supplied screws and grommets, gently mount the amplifier into position. *** do not over tighten...
Page 8
7 if your head unit has only one pair of left and right rca out put jacks use rca y adaptors to split the signal. Right output should go to channel 1/2 inputs, left output should got to channel 3/4 inputs. To audio outputs of head unit or signal processor with stereo outputs 4 channel amp with 2 c h...
Page 9
8 to audio outputs of head unit or signal processor with stereo outputs fm 2 93.3 stereo loud if your head unit has 2 pairs of rca output jacks, input front left and front right in to channels 1 and 2. Then attach radio output rear left and rear right to channels 3 and 4. Should your head unit have ...
Page 10
Power input gnd 4 ohm bridged ch1 ch2 ch3 ch3 ch4 4 ohm bridged ch4 rem +12v fuses 9 left speaker 2-4 ohm right speaker 2-4 ohm left speaker 2-4 ohm right speaker 2-4 ohm front speakers rear speakers install any combination of speakers independently on all 4 channels being careful not to load any si...
Page 11
Power input gnd 4 ohm bridged ch1 ch2 ch3 ch3 ch4 4 ohm bridged ch4 rem +12v fuses 10 right subwoofer minimum impedance 4 ohms left subwoofer minimum impedance 4 ohms when bridging the four channel amplifier, make sure that your final woofer impedance on each bridged channel is no lower than 4 ohms....
Page 12
Power input gnd 4 ohm bridged ch1 ch2 ch3 ch3 ch4 4 ohm bridged ch4 rem +12v fuses left speaker 2-4 ohm right speaker 2-4 ohm subwoofer minimum impedance 4 ohms 4 channel amplifier in 3 channel mode (csa 1000.4) channels 1 and 2 should be wired to speakers no lower than 2 ohm loads per channel in st...
Page 13
Power input gnd 4 ohm bridged ch1 ch2 ch3 ch3 ch4 4 ohm bridged ch4 rem +12v fuses 12 4 channel amplifier in 3 channel mode (csa 1000.4) subwoofer minimum impedance 4 ohms subwoofer minimum impedance 8 ohms front speakers low pass filter inductor left speaker 4 ohm right speaker 4 ohm set the crosso...
Page 14
Power input gnd 4 ohm bridged ch1 ch2 ch3 ch3 ch4 4 ohm bridged ch4 rem +12v fuses 13 4 channel with dual mixed mono configuration (csa 1000.4) subwoofer minimum impedance 8 ohms subwoofer minimum impedance 4-8 ohms front speakers rear speakers high pass filter capacitors low pass filter inductor lo...
Page 15
Ch1 ch2 4 ohm mono bridged 2 ohm stereo fuse power input gnd rem +12v 14 2 channel amplifier 2 ohm / 4 ohm stereo (csa 1000.2, 2000.2) left speaker 4 ohm or 2 ohm right speaker 4 ohm or 2 ohm for this configuration place crossover mode switch in full range..
Page 16
Ch1 ch2 4 ohm mono bridged 2 ohm stereo fuse power input gnd rem +12v 15 2 channel amplifier 4 ohm bridged (csa 1000.2, csa 2000.2) subwoofer minimum impedance 4 ohms for this configuration place crossover mode switch in low pass position..
Page 17
Power protect remote control csa5000.1 bass boost sub sonic low pass level phase filter 0db 0° 180° flat lpf 12db 15hz 55hz 50hz 500hz min max input output l r l r power input fuses speaker output gnd rem +12v 2 ohm max load 16 class a/b mono block 2 ohm amplifier (csa 3000.1, csa4000.1) dvc 4 ohm s...
Page 18
Power input fuses speaker output gnd rem +12v 1 ohm max load 17 class d mono block 1 ohm amplifier (csa 5000.1) dvc 2 ohm subwoofer in parallel =1 ohm load 2 ohm subwoofer 2 ohm subwoofer 1 ohm minimum load - or - the csa 5000.1 is a 1 ohm class d mono block amplifier. No matter how many woofers you...
Page 19
18 installation notes.
Page 20
19 specifications • rated power: 75 watts rms @ 4 ohm x 2 • rated power: 150 watts rms @ 2 ohm x 2 • peak power: 300 watts • dynamic power: 600 watts • minimum harmonic distortion: >0.01% • frequency response: 20hz - 20khz • s/n ratio: >96db • input voltage: 200mv - 8v • dimensions (l x w x h): 2” x...
Page 21
20 • rms power: 800 watts rms @ 2 ohm mono • rated power: 400 watts rms @ 4 ohm mono • peak power: 1600 watts • dynamic power: 2400 watts • minimum harmonic distortion: >0.01% • frequency response: 20hz - 20khz • s/n ratio: >96db • input voltage: 200mv - 8v • dimensions (l x w x h): 2” x 13.9” x 8” ...
Page 22
21 4 x dual vc 8 ohm speakers with series voice coils, all in parallel series: single voice coil speakers parallel: single voice coil speakers speaker wiring chart 2 ohm to amplifier 2 ohm to amplifier 4 ohm to amplifier 4 + 4 ohm 2 ohm 2 ohm 4 ohm 4 ohm 4 + 4 ohm 4 + 4 ohm 4 + 4 ohm.
Page 23
22 2 x dual vc 2 ohm speakers with series voice coils, all in parallel parallel: dual voice coil speakers series: dual voice coil speakers please note that the minimum impedance load for single a momentum cs series amplifier is 2 ohm stereo and 4 ohm mono bridged. Lower impedance loads will cause ov...
Page 24
// due to constant product improvements, these specifications are subject to change without notice. Though we tried our best to insure that this manual is free and clear of errors please don’t hold us responsible for printing errors. // copyright by cadence acoustics ltd..