Cadence MONO CLASS D Owner's Manual - Boom

Manual is about: Type RS Mono Class Amplifier

Summary of MONO CLASS D

  • Page 1

    Mono class d amplifiers.

  • Page 2: Boom

    Introduction 2 thank you for purchasing a cadence type rs amplifier. Over the past years, the technology used to create audio amplifiers has grown by leaps and bounds. We have thousands of satisfied customers still using our first generation ultra drive amplifiers which are almost 10 years old. Our ...

  • Page 3: Boom

    Features 3 gold plated terminals: bass drive equalization circuitry: “adr”: - active dynamic regulation class d audio stage performance power and protection circuitry: stiffening capacitor direct conection: mute circuit: all the terminals on the amplifier are solid brass and satin nickel plated for ...

  • Page 4: Boom

    Features 4 “arva” - automatic rail voltage adjustment circuitry: amplifier mode switch battery voltage: induction and tunnel fan cooling: protection circuitry: cadence rs amplifiers feature "arva" circuitry in their power supply. This circuit constantly monitors the output stage and under high curre...

  • Page 5: Boom

    Installation basics 5 installation basics: remote turn on conection: stiffening capacitor direct connection: using the rs amplifiers in conjunction with a multi- channel amplifier: power/ground wiring: before you begin with your installation disconnect the negative (-) terminal from your car's batte...

  • Page 6: Boom

    Mounting 6 mounting the rs amplifiers: 1 a b a 2 3 choose a convenient mounting location with unobstructed airflow. 1 - mount and fasten amplifier bracket a onto the mounting surface, with two screws as shown. 2 - slide the amplifier so that hook b engages with bracket a. 3 - fasten the front of the...

  • Page 7: Boom

    Remote turn on remote turn on mode switch line level inputs from head unit stereo rca cable from rs line out to highs amp line in cpr remote control woofer 1 ohm minimum high frequency speakers ground ground o p tio n a l c a p a c ito r fuse at battery basic single rs amplifier installation with a ...

  • Page 8: Boom

    Using the cpr remote control with the rs amplifiers 8 cpr (competition podium remote) basics level control: burst button: digital battery voltage monitor: power bargraph: installation: the optional cpr remote control can be used for street or spl competitions alike. Apart from the usual level contro...

  • Page 9: Boom

    Adjusting the system 9 setting the top panel controls adjusting the system audio preamp input audio preamp output using the built-in low pass electronic crossover subsonic filtering. Phase shift control amplifier mode switch the rs amplifiers feature rca preamp inputs. Run rca cables from your sound...

  • Page 10: Boom

    Master/slave connection diagram mono bridging 2 amplifiers into 1 woofer 10 mode switch mode switch 2 ohm minimum amplifier mode switch, inputs and remote control set the amplifier mode switches as shown connect the source to the master amplifier inputs, and an optional cpr remote control to the mas...

  • Page 11: Boom

    Mono bridging multiple pairs of amplifiers 2 or more amplifiers with separate speakers important: note the reverse speaker phase on 2nd amplifier important: reverse the speaker phase on every alternate amplifier notes on multiple amplifiers and speaker phase systems with multiple amplifiers 11 mode ...

  • Page 12: Boom

    Basic speaker wiring diagrams for various loads 12 4 ohm 8 ohm 2 ohm 4 ohm 1 ohm to amplifier 2 ohm to amplifier 4 ohm to amplifier 8 ohm to amplifier 1 ohm to amplifier 2 ohm to amplifier + + + + + + - - - - - - 4 ohm 8 ohm 4 ohm 8 ohm 4 ohm 8 ohm 2 ohm 4 ohm parallel: single voice coil speakers no...

  • Page 13: Boom

    Advanced speaker wiring diagrams for various loads 13 parallel: dual voice coil speakers 3 x dual vc 8 ohm speakers with parallel voice coils, in parallel 2 x dual vc 4 ohm speakers with parallel voice coils, in parallel 4 x dual vc 8 ohm speakers with series voice coils, all in parallel 2 x dual vc...

  • Page 14: Boom

    Troubleshooting 14 general tools needed no sound by utilizing this process of elimination you can determine where the cause of the problem is. If the amplifier goes in to diagnostic with nothing connected to it, and you are sure of proper power and ground, please contact our service department for f...

  • Page 15: Boom

    Specifications 15 due to constant product improvements, these specifications are subject to change without notice. High current rated powers are at amplifier minimum distortion and are for competition purposes. Not responsible for typographical errors. Copyright by cadence sound systems, inc. 2003 4...

  • Page 16

    Mono class d amplifiers.