1. DL manuals
  2. Cadillac
  3. Automobile
  4. 2003 Escalade
  5. Owner's Manual

Cadillac 2003 Escalade Owner's Manual

Other manuals for 2003 Escalade: Owner's Manual

Summary of 2003 Escalade

  • Page 1

    Seats and restraint systems ........................... 1-1 front seats ............................................... 1-3 rear seats ............................................... 1-8 safety belts ............................................. 1-28 child restraints ...................................

  • Page 2: Canadian Owners

    General motors, gm, the gm emblem, cadillac, the cadillac crest & wreath and the name escalade/escalade esv are registered trademarks of general motors corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without fu...

  • Page 3: Caution:

    Safety warnings and symbols you will find a number of safety cautions in this book. We use a box and the word caution to tell you about things that could hurt you if you were to ignore the warning. { caution: these mean there is something that could hurt you or other people. In the caution area, we ...

  • Page 4: Vehicle Damage Warnings

    Vehicle damage warnings also, in this book you will find these notices: notice: these mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly. Bu...

  • Page 5

    These are some examples of vehicle symbols you may find on your vehicle: v.

  • Page 6: Notes

    ✍ notes vi.

  • Page 7: Section 1

    Front seats ......................................................1-3 power seats ..................................................1-3 power lumbar ...............................................1-4 heated seats .................................................1-5 reclining seatbacks .................

  • Page 8: Section 1

    Supplemental restraint system (srs) ..............1-76 where are the air bags? ...............................1-78 when should an air bag inflate? ....................1-81 what makes an air bag inflate? .....................1-82 how does an air bag restrain? .....................1-82 what will you s...

  • Page 9: Front Seats

    Front seats power seats horizontal control: you can adjust your vehicle’s front seats with the horizontal control located on the outboard edge of each front seat. Raise or lower the front of the seat by raising or lowering the forward edge of the control. Raise or lower the rear of the seat by raisi...

  • Page 10: Power Lumbar

    Power lumbar you can increase or decrease lumbar support in an area of the lower seatback. To increase support, press and hold the front of the control. To decrease support, press and hold the rear of the control. Let go of the control when the lower seatback reaches the desired level of support. Yo...

  • Page 11: Heated Seats

    Heated seats the buttons used to control this feature are located on the front doors. The engine must be running for the heated seat feature to work. To heat the entire seat, press the horizontal button with the heated seat symbol. Press the button to cycle through the temperature settings of high, ...

  • Page 12: Reclining Seatbacks

    Reclining seatbacks your vehicle’s front seatbacks have a recline feature which is described earlier. See power seats on page 1-3 . But don’t have a seatback reclined if your vehicle is moving. { caution: sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buc...

  • Page 13: Head Restraints

    Head restraints adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. Pull straight up on the head restraint to raise it and push it down to lower it. The front head restraints can also be tilted ...

  • Page 14: Rear Seats

    Rear seats rear seat operation entering or exiting the third row seats escalade: to enter or exit the third row seat you must fold the second row seat down following the instructions later in this section. See “folding the seatback” under 60/40 split bench seat on page 1-10 . If you are exiting the ...

  • Page 15: Caution:

    To operate the easy entry seat, do the following: 1. Lift the release lever on the back of the seat, upward. 2. Tilt the seatback toward the front of the vehicle and the seat will release. 3. Pull (push if you are exiting the third row with no assistance) the seat forward until it stops. { caution: ...

  • Page 16: Heated Seats

    Heated seats if your vehicle has this feature, the buttons used to control this feature are located on the back of the center console. The engine must be running for the heated seat feature to work. To heat the seat, press the button to cycle through the temperature settings of high and low. Press t...

  • Page 17

    To fold the rear seat, do the following: 1. Make sure that nothing is under or in front of the seat. 2. Pull up on the strap loop located at the rear of the seat cushion and pull the seat cushion up. Then fold it forward. 3. Escalade: pull the seatback forward and fold it down until it is flat. Esca...

  • Page 18: Caution:

    Once the seatbacks are folded down, on escalade esv models only, the rear seat footwell area will be exposed and will have to be covered by the load floor panel(s). To create a load floor, do the following: 1. Release the panels from the seatbacks by pushing forward on the latches. 2. Then fold the ...

  • Page 19: 50/50 Split Bench Seat

    To return the seat to the upright position, do the following: 1. On escalade esv models, lift the load floor panels and latch them into the seatback. 2. Lift the seatback up and push it rearward all the way. 3. Lower the seat cushion until it latches into position. 4. Pull forward on the seatback an...

  • Page 20: Caution:

    Unfolding the seatbacks { caution: if the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. To return the seatbacks to the passenger position, do the following: 1...

  • Page 21: Caution:

    Tilting the 50/50 split bench seat 1. Fold the seatbacks forward using the instructions listed previously. 2. Unlatch the seat from the floor by pulling up on the lever labeled 2, located on the rear of the seat. 3. Lift the rear of the seat up from the floor and push it forward until it locks into ...

  • Page 22

    2. While still holding the lever 3 toward you, grasp the top of the seat and pull it toward you slightly. 3. Let go of lever 3 and pull the seat completely down. 4. Push down on the seat firmly. Try pulling it up to be sure it is locked into place. 5. Pull up on the release lever labeled 1 and then ...

  • Page 23

    3. To unlatch the rear of the seat from the floor, pull up on the release lever labeled 2, at the rear of the seat, and lift the rear of the seat up from the floor. 4. Squeeze the release handle while pulling the seat out. 5. While holding the rear of the seat up, roll the seat out of the vehicle. 1...

  • Page 24: Caution:

    Replacing the 50/50 split bench seat { caution: if the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. { caution: a seat that isn’t locked into place properly c...

  • Page 25: Caution:

    { caution: a safety belt that is improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attache...

  • Page 26: Caution:

    Folding the seatback { caution: if the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. To fold the seatback on the bench seat, do the following: pull up on the ...

  • Page 27: Caution:

    Tilting the full bench seat { caution: if the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. 1. Fold the seatbacks forward using the instructions listed previo...

  • Page 28

    Returning the seat to an upright position to return the seatback to the upright position, do the following: 1. Pull the lever (arrow) on the prop rod bracket until the rod unlatches from the seat bracket. 2. Place the prop rod back into the storage position. 3. Pull the seat toward you and push firm...

  • Page 29

    3. To unlatch the rear of the seat from the floor, pull up on the release lever labeled 2 at the rear of the seat and lift the rear of the seat up from the floor. 4. Pull on the release strap located in the lower middle of the seat to unlatch the seat from the floor and pull the seat out. Use one ha...

  • Page 30: Caution:

    Replacing the bench seat { caution: if the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. { caution: a seat that isn’t locked into place properly can move arou...

  • Page 31: Bucket Seats

    Bucket seats if your vehicle has bucket seats, the seatbacks can be reclined and the seats can be folded to give you more cargo room. Reclining the seatbacks to recline the seatback, do the following: 1. Pull up the lever located under the seat cushion. Escalade lever shown, escalade esv lever simil...

  • Page 32

    2. Pull the seatback release lever upward and pull the seatback up and fold it down until it is flat. Escalade lever shown, escalade esv lever similar. On the escalade esv models, you must first remove the headrest and store it on the top of the seat cushion as shown next. Pull the headrest out from...

  • Page 33: Caution:

    To create a load floor, do the following: 1. Release the panels from the seatbacks by pushing forward on the latches. 2. Then fold the panels back to cover the rear seat footwell area. Returning the seatbacks to an upright position { caution: if the seatback isn’t locked, it could move forward in a ...

  • Page 34: Safety Belts

    Safety belts safety belts: they are for everyone this part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. { caution: don’t let anyone ride where he or she can’t wear a safety belt properly. If you are in a crash and you’re...

  • Page 35

    In most states and in all canadian provinces, the law says to wear safety belts. Here’s why: they work . You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person w...

  • Page 36

    Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop. 1-30

  • Page 37

    The person keeps going until stopped by something. In a real vehicle, it could be the windshield... Or the instrument panel... 1-31.

  • Page 38: Safety Belts

    Or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. Questions and answers about safety belts q: won’t i be trapped in the vehicle aft...

  • Page 39

    Q: if i’m a good driver, and i never drive far from home, why should i wear safety belts? A: you may be an excellent driver, but if you’re in an accident – even one that isn’t your fault – you and your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, s...

  • Page 40: Driver Position

    Driver position this part describes the driver’s restraint system. Lap-shoulder belt the driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “seats” in the index. 3. Pick up the latch plate and pul...

  • Page 41

    5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under t...

  • Page 42: Caution:

    Q: what’s wrong with this? A: the shoulder belt is too loose. It won’t give nearly as much protection this way. { caution: you can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your...

  • Page 43: Caution:

    Q: what’s wrong with this? A: the belt is buckled in the wrong place. { caution: you can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious in...

  • Page 44: Caution:

    Q: what’s wrong with this? A: the belt is over an armrest. { caution: you can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and...

  • Page 45: Caution:

    Q: what’s wrong with this? A: the shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { caution: you can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and...

  • Page 46: Caution:

    Q: what’s wrong with this? A: the belt is twisted across the body. { caution: you can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it...

  • Page 47

    To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Safety belt use during pregnancy safety belts work for everyone, ...

  • Page 48: Center Passenger Position

    The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Right front passenger position to learn how...

  • Page 49

    Third row – lap belt when you sit in the center seating position in the third row, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt. To make the belt shorter, pull its free end as shown until the belt is snug. Buckle, positi...

  • Page 50: Rear Seat Passengers

    Rear seat passengers it’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash....

  • Page 51

    2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see safety belt extender on page 1-50...

  • Page 52: Caution:

    The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or e...

  • Page 53: Children And Small Adults

    To unlatch the belt, just push the button on the buckle. Rear safety belt comfort guides for children and small adults your vehicle may have this feature already. If it doesn’t you can get it from any gm dealer. Rear shoulder belt comfort guides will provide added safety belt comfort for older child...

  • Page 54

    1. For the second row, remove the guide from its storage clip on the trim panel near the side of the seatback. For the third row, remove the guide from its storage clip on the side of the seatback. Second row seat third row seat 1-48.

  • Page 55

    2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt. Second row seat 1-49.

  • Page 56: Safety Belt Extender

    4. Buckle, position and release the safety belt as described in rear seat passengers on page 1-44 . Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides. Safety belt extender if the ...

  • Page 57: Child Restraints

    Child restraints older children older children who have outgrown booster seats should wear the vehicle’s safety belts. If you have the choice, a child should sit in a seat that has a lap-shoulder belt to get the additional restraint a shoulder belt can provide. Q: what is the proper way to wear safe...

  • Page 58: Caution:

    { caution: never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. Q: what if a child is wearing a lap-shoulder belt, bu...

  • Page 59: Caution:

    { caution: never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That cou...

  • Page 60: Caution:

    Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint. { caution: people should nev...

  • Page 61: Caution:

    { caution: children who are up against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor...

  • Page 62: Caution:

    For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufactu...

  • Page 63: Child Restraint Systems

    Child restraint systems an infant car bed (a), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle. A rear-facing infant seat (b) pr...

  • Page 64

    A forward-facing child seat (c-e) provides restraint for the child’s body with the harness and also sometimes with surfaces such as t-shaped or shelf-like shields. A booster seat (f-g) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a sho...

  • Page 65

    Q: how do child restraints work? A: a child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased b...

  • Page 66: Caution:

    Where to put the restraint accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General motors, therefore, recommends that child restraints be secured in a rear seat including an infant riding in a rear-facing infant seat, a child riding in ...

  • Page 67: Top Strap

    If your vehicle has the passenger sensing system and you need to secure a rear-facing child restraint in the right front passenger’s seat, the passengers frontal air bag must be off. See passenger sensing system on page 1-85 and securing a child restraint in the right front seat position on page 1-7...

  • Page 68: Caution:

    In canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the united states, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. { caution: each top tether anchor is designed to ancho...

  • Page 69: Top Strap Anchor Location

    Top strap anchor location escalade esv: a child restraint with a top strap should only be used in the second or third row. Don’t use a child restraint with a top strap in the front seat because there’s no place to anchor the top strap. An anchor loop bracket for a top strap is located at the bottom ...

  • Page 70

    An anchor loop bracket for a top strap is located at the bottom rear of the seat cushion for each seating position in the second row and in the outboard passenger position in the third row for 50/50 split seats. Escalade second row seat escalade third row 50/50 split seat 1-64.

  • Page 71

    Lower anchorages and top tethers for children (latch system) your vehicle has the latch system. You will find anchors (a) in the center and right side passenger second row seating positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belt...

  • Page 72: Caution:

    In order to use the latch system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the latch system has a visible metal anchorage point in the seat where the seatback meets the...

  • Page 73: For The Latch System

    Securing a child restraint designed for the latch system 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. 3. Attach the anchor points on the child restraint to the anchors in the...

  • Page 74

    There is no top strap anchor at the third row driver side seating position. Do not secure a child seat in this position if a national or local law requires that the top strap be anchored or if the instructions that come with the child restraint say that the top strap must be anchored. If your child ...

  • Page 75

    4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you’re using a forward-facing child restraint, you may find it helpful to use your knee to pus...

  • Page 76: Center Rear Seat Position

    Securing a child restraint in a center rear seat position if your child restraint is equipped with the latch system, see lower anchorages and top tethers for children (latch system) on page 1-65 . See top strap on page 1-61 if the child restraint has one. Second row the center seat position in the s...

  • Page 77

    1. Make the belt as long as possible by tilting the latch plate and pulling it along the belt. 2. Put the restraint on the seat. 3. Run the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button is p...

  • Page 78: Right Front Seat Position

    5. To tighten the belt, pull its free end while you push down on the child restraint. If you’re using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6. Push and pull the child restraint in different directions t...

  • Page 79: Caution:

    { caution: a child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inflates. This is because the back of the rear facing child restraint would be very close to the inflating air bag. Be sure the air bag is off before using a rear-facing chil...

  • Page 80

    4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 1-74.

  • Page 81

    6. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. You should not be able to pull m...

  • Page 82: Supplemental Restraint

    Supplemental restraint system (srs) this part explains the frontal and side impact supplemental restraint systems (srs) or air bag systems. Your vehicle has four air bags – a frontal air bag for the driver, another frontal air bag for the right front passenger, a side impact air bag for the driver, ...

  • Page 83: Caution:

    Caution: (continued) the side impact air bags for the driver and right front passenger are designed to inflate only in moderate to severe crashes where something hits the side of your vehicle. They aren’t designed to inflate in frontal, in rollover or in rear crashes. Everyone in your vehicle should...

  • Page 84: Where Are The Air Bags?

    There is a air bag readiness light on the instrument panel cluster, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See air bag readiness light on page 3-37 for more information. Where are the ai...

  • Page 85

    The right front passernger’s frontal air bag is in the instrument panel on the passenger’s side. The driver’s side impact air bag is in the side of the driver’s seatback closest to the door. 1-79.

  • Page 86: Caution:

    The right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door. { caution: if something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death. The pat...

  • Page 87

    When should an air bag inflate? The driver’s and right front passenger’s frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system’s designed “threshold level.” in addition, your vehic...

  • Page 88

    Seat position sensors vehicle’s with dual stage air bags are also equipped with special sensors which enable the sensing system to monitor the position of both the driver and passenger front seats. The seat position sensor provides information which is used to determine if the air bags should deploy...

  • Page 89: Inflates?

    What will you see after an air bag inflates? After the air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s fr...

  • Page 90

    • your vehicle is equipped with electronic frontal sensors which help the sensing system distinguish between a moderate and a more severe frontal impact. Your vehicle is also equipped with a crash sensing and diagnostic module, which records information about the frontal air bag system. The module r...

  • Page 91: Passenger Sensing System

    Passenger sensing system if your rearview mirror has one of the indicators pictured in the following illustrations, your vehicle has a passenger sensing system. The indicator will be visible when you turn your ignition key to start or run. The words on and off or the symbol for on and off, will be v...

  • Page 92: Caution:

    Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General motors, therefore, recommends that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child sea...

  • Page 93

    • a right front passenger takes his/her weight off of the seat for a period of time • the right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints • or if there is a critical problem with the air bag system or the passenger sensing system. When th...

  • Page 94: Caution:

    { caution: if the air bag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the air bag system. If this ever happens, caution: (continued) caution: (continued) have the vehicle serviced promptly, because an adult-size person sitting...

  • Page 95: Vehicle

    Servicing your air bag-equipped vehicle air bags affect how your vehicle should be serviced. There air bag system parts in several places around your vehicle. You don’t want the system to inflate while someone is working on your vehicle. Your dealer and the service manual have information about serv...

  • Page 96: Bag-Equipped Vehicle

    Adding equipment to your air bag-equipped vehicle q: is there anything i might add to the front or sides of the vehicle that could keep the air bags from working properly? A: yes. If you add things that change your vehicle’s frame, bumper system, front end or side sheet metal or height, they may kee...

  • Page 97: After A Crash

    Replacing restraint system parts after a crash { caution: a crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working prop...

  • Page 98: Notes

    ✍ notes 1-92.

  • Page 99: Section 2

    Keys ...............................................................2-3 remote keyless entry system .........................2-4 remote keyless entry system operation ...........2-5 doors and locks .............................................2-8 door locks .............................................

  • Page 100: Section 2

    Storage areas ................................................2-44 glove box ...................................................2-44 cupholder(s) ................................................2-44 center console storage area .........................2-45 luggage carrier ..............................

  • Page 101: Keys

    Keys { caution: leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children. 2-3.

  • Page 102

    Your vehicle has one double-sided key for the ignition and door locks. If you ever lose your keys, your dealer will be able to assist you with obtaining replacements. In an emergency contact cadillac roadside service ® . See roadside service on page 7-6 for more information. If you ever lock your ke...

  • Page 103: Operation

    At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: • check the distance. You may be too far from your vehicle. You may need to stand cl...

  • Page 104

    Q (lock): pressing this button once will lock all of the doors. Pressing the button again within three seconds may cause the horn to chirp for lock confirmation. You can choose different feedback options for each press of the lock button, such as having the vehicle’s perimeter lamps flash and/or hav...

  • Page 105

    Battery replacement under normal use, the battery in your remote keyless entry transmitter should last about two years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s prob...

  • Page 106: Doors And Locks

    Doors and locks door locks { caution: unlocked doors can be dangerous. • passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. You increase the chance of being thrown out of the vehicle in a crash if the doors ...

  • Page 107: Power Door Locks

    There are several ways to lock and unlock your vehicle. To unlock the door from the outside, use the keyless entry system or the key. To unlock the door from the inside, slide the manual lever forward. To lock the door, slide the manual lever rearward. Power door locks the power door lock switches a...

  • Page 108: Delayed Locking

    Cargo area door lock switch your vehicle may have a power lock switch on the passenger side of the liftgate opening trim. This switch operates identically to the power door lock switches on the driver’s and front passenger’s armrests. Delayed locking when locking the doors with the power lock switch...

  • Page 109: Locks

    Programmable automatic door locks your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the driver information center (dic), or by the following method. Programmable locking feature the follow...

  • Page 110

    3. Press the door lock switch once. You will hear one, two, or three chimes. The number of chimes tells you which lock mode is currently selected. Continue to press the door lock switch until the number of chimes that you hear matches the number of the mode that you want. If you take longer than 30 ...

  • Page 111: Rear Door Security Locks

    2. Turn the key to run and lock twice. Then, with the key in lock, release the turn signal/multifunction lever. Once you do this, the doors will lock and unlock, the horn will chirp twice, and a 30-second timer will begin. You are now ready to program the automatic door unlock feature. 3. Press the ...

  • Page 112: Lockout Protection

    To use one of the locks, do the following: 1. Open one of the rear doors. 2. Move the lever forward to engage the rear door security lock. 3. Close the door. 4. Do the same thing to the other rear door. The rear doors or your vehicle cannot be opened from the inside when this feature is in use. If y...

  • Page 113: Liftgate/liftglass

    Liftgate/liftglass { caution: it can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (co) gas can come into your vehicle. You can’t see or smell co. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or othe...

  • Page 114: Windows

    Windows { caution: leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather. 2-16.

  • Page 115: Power Windows

    Power windows the controls for the power windows are located on the armrest on each of the side doors. The switches operate the windows when the ignition is in run, accessory or when retained accessory power (rap) is active. See “retained accessory power” under ignition positions on page 2-20 . The ...

  • Page 116: Theft-Deterrent Systems

    Theft-deterrent systems vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content theft-deterrent your vehicle is equipped with a content theft-deterrent alarm s...

  • Page 117: Passlock

    Testing the alarm the alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter. 3. G...

  • Page 118: Vehicle

    Starting and operating your vehicle new vehicle break-in notice: your vehicle doesn’t need an elaborate “break-in.” but it will perform better in the long run if you follow these guidelines: • keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km). • don’t drive at any one spee...

  • Page 119: Starting Your Engine

    Notice: if your key seems stuck in lock and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? Turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of these works, then your vehicle needs service. B (access...

  • Page 120

    When starting your engine in very cold weather (below 0°f or − 18°c), do this: 1. With your foot off the accelerator pedal, turn the ignition key to start and hold it there up to 15 seconds. When the engine starts, let go of the key. 2. If your engine still won’t start (or starts but then stops), it...

  • Page 121: Engine Coolant Heater

    Engine coolant heater your vehicle may be equipped with an engine coolant heater. In very cold weather, 0°f ( − 18°c) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of...

  • Page 122: Caution:

    How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you’ll be parking your vehicle. The dealer can give...

  • Page 123: Caution:

    Neutral (n): in this position, your engine doesn’t connect with the drive wheels. To restart when you’re already moving, use neutral (n) only. { caution: shifting into a drive gear while your engine is “racing” (running at high speed) is dangerous. Unless your foot is firmly on the brake pedal, your...

  • Page 124

    First (1): this position gives you even more power, but lower fuel economy than second (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in first (1) while the vehicle is moving forward, the transmission won’t shift into first gear until the vehicle is going ...

  • Page 125: Parking Brake

    Parking brake to set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. A chime will activate and the warning light will flash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at lea...

  • Page 126: Shifting Into Park (P)

    Shifting into park (p) { caution: it can be dangerous to get out of your vehicle if the shift lever is not fully in park (p) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your v...

  • Page 127: Caution:

    • move the lever up as far as it will go. 3. Turn the ignition key to lock. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in park (p). Leaving your vehicle with the engine running { caution: it can be dangerous to leave your...

  • Page 128: Shifting Out Of Park (P)

    Torque lock if you are parking on a hill and you don’t shift your vehicle into park (p) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of park (p). This is called torque lock. To prevent torque...

  • Page 129: Caution:

    Parking over things that burn { caution: things that can burn could touch hot exhaust parts under your vehicle and ignite. Don’t park over papers, leaves, dry grass or other things that can burn. Engine exhaust { caution: engine exhaust can kill. It contains the gas carbon monoxide (co), which you c...

  • Page 130: Are Parked

    Running your engine while you are parked it’s better not to park with the engine running. But if you ever have to, here are some things to know. { caution: idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under “engine exh...

  • Page 131: Mirrors

    Mirrors automatic dimming rearview mirror with onstar ® , compass and temperature display your vehicle may have this feature. When on, the mirror automatically dims to the proper level to minimize glare from lights behind you after dark. The mirror also includes a duel display in the upper right cor...

  • Page 132

    Self dimming mirror operation the self dimming mirror function is turned on automatically each time the ignition is started. To operate the mirror, do the following: 1. Make sure the green indicator light, is lit. If it’s not, press and hold the on/off button for approximately six seconds until the ...

  • Page 133

    Compass calibration the compass may need calibration if one of the following occurs: • after approximately five seconds, the display does not show a compass heading (n for north, for example), there may be a strong magnetic field interfering with the compass. Such interference may be caused by a mag...

  • Page 134: Outside Power Mirrors

    Outside power mirrors the controls are located on the driver’s door armrest. Move the upper selector switch to the left or right to choose the mirror you want to adjust; then press the dots located on the four-way control pad to adjust the mirror. To fold or unfold the mirrors, move the selector swi...

  • Page 135: Outside Heated Mirrors

    Outside heated mirrors your vehicle may have this feature. When you press this button, a defogger warms the heated driver’s and passenger’s outside rearview mirrors to help clear them of ice, snow and condensation. If your vehicle has a rear window defogger, it will also operate when you press this ...

  • Page 136: Onstar

    Onstar ® system onstar ® uses global positioning system (gps) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services. A complete onstar ® user’s guide and the terms and conditions of ...

  • Page 137

    Luxury and leisure plan • all directions and connections plan services • personal concierge onstar ® personal calling with onstar ® personal calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nation...

  • Page 138: Homelink

    Homelink ® transmitter if your vehicle has this feature, the control buttons are located on the driver’s sun visor. Homelink ® , a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door op...

  • Page 139: Programming The Homelink

    Programming the homelink ® transmitter do not use the homelink ® transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before april 1, 1982. If you have a newer garage door opener with rolling codes, please ...

  • Page 140

    4. The indicator light will flash slowly at first and then rapidly after homelink ® successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained homelink ® button and observe the indicator light. If the indicator light stays on ...

  • Page 141

    Gate operator and canadian programming canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for homelink ® to pick up the signal during programming. Similarly, some u.S. Gate operators are manufactured to “...

  • Page 142: Storage Areas

    Reprogramming a single homelink ® button to program a device to homelink ® using a homelink ® button previously trained, follow these steps: 1. Press and hold the desired homelink ® button. Do not release the button. 2. The indicator light will begin to flash after 20 seconds. While still holding th...

  • Page 143: Luggage Carrier

    Center console storage area your vehicle has a console compartment between the bucket seats. To open it, press the button on the side of the console and swing the console lid open. The console may be equipped with an accessory power outlet inside. See accessory power outlets on page 3-23 . The rear ...

  • Page 144: Rear Storage Area

    Be sure the cargo is properly loaded. • if small heavy objects are placed on the roof, place the load in the area over the rear wheels (behind the rear passenger doors on esv models). If you need to, cut a piece of 3/8 inch plywood to fit inside the crossrails and siderails to spread the load. If pl...

  • Page 145: Rear Seat Armrest

    Rear seat armrest your vehicle’s second row seat may have an armrest/storage compartment. Pull the loop at the top of the armrest out to lower the armrest. To open the compartment, if equipped, push the button on the front of the armrest and pull the top open. Convenience net the convenience net (if...

  • Page 146

    To remove the cover from the vehicle, do the following: 1. Let the cover go all the way into the holder. 2. Then, grasping the passenger’s side cover endcap, push the cover endcap toward the driver’s side of the vehicle. The endcap should lock in the compressed position. 3. Lift the cover up on the ...

  • Page 147: Sunroof

    Sunroof your vehicle may be equipped with a power sliding sunroof. To open or close your sunroof, the ignition needs to be on or rap needs to be active. See “retained accessory power” under ignition positions on page 2-20 . Press and release the rear side of the button located in the front overhead ...

  • Page 148: Vehicle Personalization

    Vehicle personalization memory seat if your vehicle has this feature, then the controls for the memory function are located on the driver’s door. These buttons are used to program and recall memory settings for the driver’s seat, throttle and brake pedals, both the driver’s and passenger’s outside m...

  • Page 149

    The seat, throttle and brake pedals and mirror positions can also be recalled when placing the key in the ignition if programmed to do so through the driver information center (dic). See dic operation and displays on page 3-51 . To stop recall movement of the memory seat feature at any time, press o...

  • Page 150: Notes

    ✍ notes 2-52.

  • Page 151: Section 3

    Instrument panel overview ...............................3-4 hazard warning flashers ................................3-6 other warning devices ...................................3-7 horn .............................................................3-7 tilt wheel ........................................

  • Page 152: Section 3

    Theft-deterrent feature ................................3-101 audio steering wheel controls ......................3-102 dvd distortion ............................................3-102 understanding radio reception ....................3-103 care of your cassette tape player ...............3-103 care...

  • Page 153: Notes

    ✍ notes 3-3.

  • Page 154: Instrument Panel Overview

    Instrument panel overview 3-4.

  • Page 155

    The main components of your instrument panel are the following: a. Air outlets. See outlet adjustment on page 3-31 . B. Exterior lamps control. See exterior lamps on page 3-15 . C. Turn signal/multifunction lever. See turn signal/multifunction lever on page 3-8 . D. Onstar ® and radio steering wheel...

  • Page 156: Hazard Warning Flashers

    Hazard warning flashers your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. But they won’t flash if you’re braking. The hazard warning flasher button is located on the top of the steering column....

  • Page 157: Other Warning Devices

    Other warning devices if you carry reflective triangles, you can use them to warn others. Set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn to sound the horn, press the center pad on the steering wheel. Tilt wheel the tilt steering wheel allows you to adjust the ste...

  • Page 158

    Turn signal/multifunction lever the lever on the left side of the steering column includes the following: • turn and lane change signals • headlamp high/low-beam changer • flash-to-pass • windshield wipers • windshield washer • cruise control for information on the exterior lamps, see exterior lamps...

  • Page 159

    Turn signal on chime if your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each flash of the turn signal and the message turn signal on will also appear in the dic. To turn the chime and message off, move the turn signal lever to the off position. Headlamp high/l...

  • Page 160: Caution:

    Windshield wipers you control the windshield wipers by turning the band with the wiper symbol on it. 8 (mist): for a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longe...

  • Page 161

    Rear window washer/wiper this knob is located on the instrument panel to the left of the steering wheel. To turn the rear wiper on, turn the knob to either 1 or 2. For long delayed wiping, turn the knob to 1. For short delayed wiping, turn the knob to 2 9 (off): to turn the wiper off, turn the knob ...

  • Page 162: Caution:

    If you apply your brakes, the cruise control will shut off. { caution: • cruise control can be dangerous where you can’t drive safely at a steady speed. So, don’t use your cruise control on winding roads or in heavy traffic. • cruise control can be dangerous on slippery roads. On such roads, fast ch...

  • Page 163

    Resuming a set speed suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch briefly from on to resume...

  • Page 164

    Passing another vehicle while using cruise control use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using cruise control on hills how well your cruise control will work on hills depends u...

  • Page 165: Exterior Lamps

    Exterior lamps the control on the driver’s side of your instrument panel operates the exterior lamps. The exterior lamp control has four positions: 9 (off): turn the knob to this position and release it to turn off all exterior lamps including the drls. A light near the symbol will be lit when in th...

  • Page 166

    Automatic headlamp system when it is dark enough outside and the headlamp switch is in auto, your automatic headlamp system will turn on your headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, roof marker lamps and the instrument panel lights....

  • Page 167

    Daytime running lamps daytime running lamps (drl) can make it easier for others to see the front of your vehicle during the day. Drl can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime run...

  • Page 168: Interior Lamps

    The fog lamps will go off whenever your high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. The fog lamps will be cancelled after the ignition is turned off. If you still want to use the fog lamps after you restart the vehicle, you will need to press the fog la...

  • Page 169

    Exit lighting with exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. Reading lamps if your vehicle has reading lamps, press the button located next to the lamp to turn it on. The lamps can b...

  • Page 170: (Urpa)

    Ultrasonic rear parking assist (urpa) ultrasonic rear parking assist can help you to determine how close an object is to your rear bumper within a given area, making parking easier. The urpa display is located inside the vehicle, on the passenger’s side rear upper trim panel. It has three color-code...

  • Page 171: Caution:

    { caution: even with the ultrasonic rear park assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system doesn’t detect objects that are more than 5 feet (1.5 meters) behind the vehicle. ...

  • Page 172

    If the urpa display flashes red if the urpa system is not functioning properly, the display will flash red, indicating that there is a problem. The light will also flash red while driving if any of the following conditions exist: • a trailer or trailer-hitch ball mount is attached to your vehicle. •...

  • Page 173: Accessory Power Outlets

    Accessory power outlets with accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or cb radio. Your vehicle is equipped with many accessory power outlets. One outlet is located in the center console. Press the button on the side of the console door to a...

  • Page 174: Analog Clock

    Analog clock to adjust the clock, do the following: 1. Locate the adjustment button to the lower left corner of the clock. 2. Push and hold the adjustment button to spin the clock hands. Release the button before you get to the desired time. 3. Push and release the button to increase the time by one...

  • Page 175

    Driver’s side temperature knob the driver’s side knob is used to adjust the temperature of the air coming through the system on the driver’s side. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always flow through the system as the vehicle i...

  • Page 176

    Automatic operation auto (automatic): when automatic operation is active the system will control the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the auto button. When auto is selected, the display will change to ...

  • Page 177

    9 (off): press this button to turn off the entire climate control system. Outside air will still enter the vehicle, and will be directed to the floor. This direction can be changed by pressing the mode button. The temperature can also be adjusted using either temperature knob. Press the up or down a...

  • Page 178

    @ (recirculation): press this button to limit the amount of outside air entering your vehicle. The light on the recirculation button will glow. This is helpful when you are trying to limit odors entering your vehicle and for maximum air conditioning performance in hot weather. Press this button agai...

  • Page 179

    If the driver’s and passenger’s temperature settings are the same when auto is pressed, the temperature setting and both arrows will be displayed for five seconds along with the automatic air delivery mode and fan speed. After the five second update, the display will change to show the temperature s...

  • Page 180

    Defogging and defrosting you can use either defog or front defrost to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture. Use the front defrost button to defrost the front windshield. - (defog): use this setting to clear the windows of fog or moisture...

  • Page 181: Outlet Adjustment

    Outlet adjustment use the air outlets located in the center and on the side of your instrument panel to direct the airflow. Your vehicle has air outlets that allow you to adjust the direction and amount of airflow inside the vehicle. Move the louvers up or down. Use the thumbwheel next to or underne...

  • Page 182

    Aux: turn the knob, located on the left side of the control panel, to this position to allow the rear seat passengers to have control over the rear climate control system. See “rear passenger console control” later for more information. 9 (off): turn the knob, located on the left side of the control...

  • Page 183

    % (mode): press this button to select the air delivery mode and auto mode. Choose auto if you want the system to automatically regulate the airflow. See “auto mode” later in this section for more information on using this feature. B (temperature): press this button up or down to increase or decrease...

  • Page 184: Warning Lights, Gages And

    Warning lights, gages and indicators this part describes the warning lights and gages on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to...

  • Page 185

    United states version shown, canada similar. 3-35.

  • Page 186: Speedometer And Odometer

    Speedometer and odometer your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle’s odometer works together with the driver information center. You can set a personal trip and business trip odometer. See “trip information” under dic operation...

  • Page 187: Air Bag Readiness Light

    Air bag readiness light there is an air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensors, the air bag m...

  • Page 188: Caution:

    Passenger air bag status indicator if your vehicle has the passenger sensing system your rearview mirror will have a passenger air bag status indicator. When the ignition key is turned to run or start, the passenger air bag status indicator will light on and off, or the symbol for on and off, for se...

  • Page 189: Caution:

    If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. { caution: if the off indicator and the air bag readiness light ever come on together, it means tha...

  • Page 190: Voltmeter Gage

    Voltmeter gage when your engine is not running, but the ignition is in run, this gage shows your battery’s state of charge in dc volts. When the engine is running, the gage shows the condition of the charging system. Readings between the low and high warning zones indicate the normal operating range...

  • Page 191: Caution:

    This light should come on briefly when you turn the ignition key to run. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push....

  • Page 192: Light

    Anti-lock brake system warning light with the anti-lock brake system, this light will come on when you start your engine and may stay on for several seconds. That’s normal. If the light doesn’t come on then, have it fixed so it will be ready to warn you if there is a problem. If the light stays on, ...

  • Page 193

    Engine coolant temperature gage this gage shows the engine coolant temperature. It also provides an indicator of how hard your vehicle is working. During a majority of the operation, the gage will read 210°f (100°c) or less. If you are pulling a load or going up hills, it is normal for the temperatu...

  • Page 194: Malfunction Indicator Lamp

    See driver information center (dic) on page 3-51 for further information. If the transmission fluid reaches temperatures of approximately 275°f (135°c) or greater, the dic will display a trans hot idle engine warning message and a chime will sound. Pull the vehicle off the roadway when it is safe to...

  • Page 195

    Notice: if you keep driving your vehicle with this light on, after a while, your emission controls may not work as well, your fuel economy may not be as good and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: modifications mad...

  • Page 196

    If the light is on steady you may be able to correct the emission system malfunction by considering the following: did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See filling your tank on page 5-7 . The diagnostic system can determine...

  • Page 197

    Emissions inspection and maintenance programs some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know...

  • Page 198: Oil Pressure Gage

    Oil pressure gage the oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kpa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low press...

  • Page 199: Security Light

    Security light this light will come on briefly when you turn the key toward start. The light will stay on until the engine starts. If the light flashes, the passlock ® system has entered a tamper mode. If the vehicle fails to start, see passlock ® on page 2-19 . If the light comes on continuously wh...

  • Page 200: Fuel Gage

    Fuel gage when the ignition is on, the fuel gage tells you about how much fuel you have left in your tank. The gage will first indicate empty before you are out of fuel, and you should get more fuel as soon as possible. Here are some situations you may experience with your fuel gage. None of these i...

  • Page 201

    Driver information center (dic) the dic display is located on the instrument panel cluster above the steering wheel. The dic can display information such as the trip odometer, fuel economy and personalization features. Vehicles without the dic buttons will not have all the features as the regular di...

  • Page 202

    Trip information button press the trip information button to scroll through the odometer, personal trip on/off, business trip on/off, hourmeter, annual log and timer. If the personal trip and/or the business trip are set to on, you will also be able to scroll through more messages. See “personal tri...

  • Page 203

    To reset the personal or business trip information, do the following: press and hold the select button for one second while in one of the personal or business trip modes. This will reset all of the information for the personal or business trip. You can also reset the personal: xx mi, or business: xx...

  • Page 204

    Fuel information button use the fuel information button to scroll through the range, average fuel economy, instant fuel economy and the gm oil life system. Fuel range press the fuel information button until range appears to display the remaining distance you can drive without refueling. It’s based o...

  • Page 205

    Personalization button you can program certain features to a preferred setting for up to two people. Press the personalization button to scroll through the following personalization features. All of the personalization options may not be available on your vehicle. Only the options available will be ...

  • Page 206

    Choose one of the four options and press the personalization button while your choice is displayed on the dic to select it and move on to the next feature. For more information on alarm warning type see content theft-deterrent on page 2-18 . Automatic locking press the personalization button until a...

  • Page 207

    Delayed locking if your dic does not have this feature, you can still program the delayed locking feature. See delayed locking on page 2-10 for more information. When locking the doors with the power lock switch or the keyless entry transmitter and a door or the liftgate is open, the delayed locking...

  • Page 208

    Seat position recall on remote: the memory seat position you saved will be recalled when you unlock the vehicle with the remote keyless entry transmitter. Choose one of the three options and press the personalization button while it is displayed on the dic to select it and move on to the next featur...

  • Page 209

    Remote unlock feedback press the personalization button until remote unlock feedback appears in the display. To select your personalization for the feedback you will receive when unlocking the vehicle with the remote keyless entry transmitter, press the select button while remote unlock feedback is ...

  • Page 210

    Curb view assist press the personalization button until curb view assist appears in the display. To select your personalization for curb view assist, press the select button while curb view assist is displayed on the dic. Pressing the select button will scroll through the following choices: curb vie...

  • Page 211

    Display units (eng/met) press the personalization button until display units appears in the display. To select english or metric, press the select button while display units is displayed on the dic. Pressing the select button will scroll through the following choices: • units: english • units: metri...

  • Page 212: Dic Warnings And Messages

    Dic warnings and messages warning messages are displayed on the dic to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. If there is more than one message that needs to be displayed they will appear one after anoth...

  • Page 213

    Engine coolant hot if the cooling system temperature gets hot, this message will appear in the dic. Stop the vehicle and let the engine idle in park (p) to allow the coolant to reach a safe temperature. This message will clear when the coolant temperature drops to a safe operating temperature. Press...

  • Page 214: Caution:

    Service brake booster if your vehicle has vacuum assist power brakes, this message will be displayed on the dic when there is a problem with the supplemental brake assist system. If the message is displayed immediately after starting the vehicle or the message appears while driving, your supplementa...

  • Page 215

    Turn signal on if a turn signal is left on for 3/4 of a mile (1.2 km), this message will appear on the display and you will hear a chime. Move the turn signal/multifunction lever to the off position. Pressing the select button will clear it from the dic display. Fuel level low if the fuel level is l...

  • Page 216

    Transmission hot if the transmission fluid temperature becomes high, the message center will display this message. When the transmission enters the protection mode, you may notice a change in the transmission shifting patterns. When the transmission fluid temperature returns to normal, the display w...

  • Page 217

    Passenger door ajar if the passenger’s door is not fully closed and the vehicle is in a drive gear, this message will appear on the display and you will hear a chime. Stop and turn off the vehicle, check the door for obstacles, and close the door again. Check to see if the message still appears on t...

  • Page 218

    Traction active when the traction control system has detected that any of the vehicle’s wheels are slipping, the traction control system will activate and this message will appear on the dic. See stabilitrak ® system on page 4-10 for more information. Traction sys limited new text under development....

  • Page 219

    Stability sys disabled the stability sys disabled message will turn on when you press the stabilitrak ® button, or when the stability control has been automatically disabled. To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave stabilitrak ...

  • Page 220: Audio System(S)

    Audio system(s) notice: before you add any sound equipment to your vehicle – like a tape player, cb radio, mobile telephone or two-way radio – be sure you can add what you want. If you can, it’s very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’...

  • Page 221

    Radio with cassette and cd radio data system (rds) your audio system is equipped with a radio data system (rds). Rds features are available for use only on fm stations that broadcast rds information. With rds, your radio can do the following: • seek to stations broadcasting the selected type of prog...

  • Page 222

    Playing the radio pwr (power): press this knob to turn the system on and off. Vol (volume): turn this knob to increase or to decrease volume. Auto vol (automatic volume): your vehicle is equipped with bose audiopilot ® noise compensation technology. Audiopilot monitors the level of noise in the vehi...

  • Page 223

    Finding a station band: press this button to switch between am, fm1, fm2, or xm1, xm2 (usa only, if equipped). The display will show your selection. Tune: turn this knob to choose radio stations. Q seek r : press the right or the left arrow to seek to the next or to the previous station and stay the...

  • Page 224

    Setting the tone (bass/treble) audio: press and release the audio knob until bass or treb appears on the display. Turn the knob to increase or to decrease. The display will show the bass or treble level. If a station is weak or noisy, you may want to decrease the treble. To adjust the bass and trebl...

  • Page 225

    Adjusting the speakers (balance/fade) audio: to adjust the balance between the right and the left speakers, push and release the audio knob until bal appears on the display. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speak...

  • Page 226

    3. Once the desired category is displayed, press either scan arrow, and the radio will begin scanning within your chosen category. 4. Press wither scan arrow again to stop scanning. Band (alternate frequency): alternate frequency allows the radio to switch to a stronger station with the same program...

  • Page 227

    If the whole message is not displayed, parts of it will appear every three seconds. To scroll through the message at your own speed, press the info button repeatedly. A new group of words will appear on the display with each press. Once the complete message has been displayed, the information symbol...

  • Page 228

    Xm™ radio messages radio display message condition action required xl (explicit language channels) xl on the radio display, after the channel name, indicates content with explicit language. These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-xmxm (9696). Updat...

  • Page 229

    Xm™ radio messages (cont’d) radio display message condition action required no info category name not available no category information is available at this time on this channel. Your system is working properly. No info no text/informational message available no text or informational messages are av...

  • Page 230

    Playing a cassette tape your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible should face to the right. If the ignition is on, but the radio ...

  • Page 231

    4 fwd (forward): press this pushbutton to advance quickly to another part of the tape. Press this pushbutton again to return to playing speed. The radio will play while the tape advances. The station frequency and fwd will appear on the display. You may select stations during forward operation by us...

  • Page 232

    Clean: if this message appears on the display, the cassette tape player needs to be cleaned. It will still play tapes, but you should clean it as soon as possible to prevent damage to the tapes and player. See care of your cassette tape player on page 3-103 . If any error occurs repeatedly or if an ...

  • Page 233

    1 prev (previous): press this pushbutton to go to the previous track if the current track has been playing for less than eight seconds. If pressed when the current track has been playing for more than eight seconds, it will go to the beginning of the current track. Track and the track number will ap...

  • Page 234

    Band: press this button to listen to the radio when a cd is playing. The cd will stop but remain in the player. Tape disc: press this button to play a tape when listening to the radio. Press this button to switch between the tape and compact disc if both are loaded. The inactive tape or cd will rema...

  • Page 235

    Rear seat entertainment system your vehicle may have the optional digital versatile disc (dvd) rear seat entertainment (rse) system. The rse system includes a dvd player, a video display screen, two sets of wireless headphones, and a remote control. Before you drive the rse system is for rear seat p...

  • Page 236

    C (stop): press this button to stop the play of the dvd player. Press this button twice to return to the beginning of the dvd. K (play/pause): press this button to turn the dvd player on, to start play of a dvd or cd and to toggle between play and pause of a dvd or cd. Y (menu): press this button to...

  • Page 237

    Ejecting a disc press the eject button on the dvd player to eject the disc. If a disc is ejected from the player, but is not removed, the dvd player will reload the disc within 25 to 30 seconds. The disc will then be stored in the dvd player. The dvd player will not resume play of this disc automati...

  • Page 238

    Video screen the video screen is located in the overhead console. To use the video screen, push forward on the release latch and the screen will fold down. Adjust the screen’s position as desired. When the video screen is not in use, push it up into its latched position. The dvd player and display w...

  • Page 239

    Z (display menu): press this button to modify the video screen display characteristics. E (audio): press this button to call-up a menu that will operate only when a dvd is being played. The format and content of this function is defined by the disc and is dependent of the disc. R (fast reverse): pre...

  • Page 240

    { (subtitle): press this button to call-up a menu that will operate only when a dvd is being played. The format and content of this function is defined by the disc and is dependent of the disc. [ (fast forward): press this button to fast forward the dvd or cd. To stop fast forwarding, press this but...

  • Page 241

    Headphones the rse system includes two sets of wireless infrared headphones. Each set of headphones has an on/off control. An indicator light will illuminate on the headphones when they are on. If the light does not illuminate, the batteries may need to be replaced. See “battery replacement” later i...

  • Page 242

    Stereo rca jacks the rca jacks are located behind the video screen on the front of the dvd console. The rca jacks allow you to connect audio and video from an auxiliary device such as a camcorder or a video game unit to your rse system just as you would to a standard television. Standard rca cables ...

  • Page 243

    The rse system is capable of outputting audio to the vehicle speakers by using the radio. The rse system may be selected as an audio source on the radio if the rse system power is on. Once the rse system is selected as an audio source on the radio you may adjust the speaker volume on the radio. If t...

  • Page 244

    Problem recommended action the disc was ejected, but it was pulled back into the dvd player. The disc is being stored in the dvd player. Press the eject button again to eject the disc. In auxiliary mode, the picture moves or scrolls. Check the signal coming from the auxiliary device and make sure th...

  • Page 245

    Problem recommended action the auxiliary source is running but there is no picture or sound. Press the srce button to change from the dvd player mode to the auxiliary source mode. Check to make sure that the auxiliary source is connected to the inputs properly. My disc is stuck in the player. The lo...

  • Page 246: Navigation/radio System

    Navigation/radio system the display screen is located in the center of the instrument panel. There are “hard” buttons and a touch sensitive screen. Your vehicle may be equipped with an am-fm radio navigation radio system that includes digital sound processing (dsp), radio data system (rds) with prog...

  • Page 247: Rear Seat Audio (Rsa)

    Rear seat audio (rsa) this feature allows rear seat passengers to listen to any of the audio sources: radio, cassette tapes, cds, dvds, or xm™ (48 contiguous us states, if equipped) depending on your vehicles options. In the event that the front seat passengers are listening to any of these remote s...

  • Page 248

    U (volume): turn the knob to increase or to decrease volume. The left knob controls the left headphone and the right knob controls the right headphone. Src (source): press this button to select an audio source: radio, cassette tapes, cds, dvds, or xm™ (48 contiguous us states, if equipped), dependin...

  • Page 249: Cd Changer

    Cd changer the compact disc changer plays up to six standard size cds continuously. Individual cds may be loaded or ejected into or from any position. A green light on each numbered button indicates a cd is loaded in the respective position. An amber light on a numbered button indicates that a cd is...

  • Page 250

    To eject a single cd, perform the following steps: 1. Press the eject button (upward pointing arrow). The buttons with loaded cds will blink amber. 2. Press one of the amber blinking buttons to select the location of the cd you want to eject. The changer will move to that location and eject the cd. ...

  • Page 251: Theft-Deterrent Feature

    6 rdm (random): press this button to hear the tracks in random, rather than sequential, order. Rdm all will appear on the radio display, which will randomly play all of the loaded cds. Press and hold this button until you hear a beep and the radio will display rdm one, which will randomly play the t...

  • Page 252: Dvd Distortion

    Audio steering wheel controls you can control certain radio functions using the buttons on your steering wheel. G (onstar/voice recognition): you can press this button to interact with the onstar ® system. See the onstar ® manual provided with your vehicle for more information. Prog (program): press...

  • Page 253

    Understanding radio reception am the range for most am stations is greater than for fm, especially at night. The longer range, however, can cause stations to interfere with each other. Am can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise if you e...

  • Page 254: Care Of Your Cd Changer

    When cleaning the cassette tape player with the recommended non-abrasive cleaning cassette, it is possible that the cassette may eject, because the cut tape detection feature on your radio may recognize it as a broken tape, in error. To prevent the cleaning cassette from being ejected, use the follo...

  • Page 255: Cleaning The Video Screen

    Cleaning the video screen pour some isopropyl or rubbing alcohol on a clean cloth and gently wipe the video screen. Do not spray directly onto the screen and do not press too hard or too long on the video screen. Diversity antenna system your am-fm antennas are located in the rear side windows. Be s...

  • Page 256: Notes

    ✍ notes 3-106.

  • Page 257: Section 4

    Your driving, the road, and your vehicle ..........4-2 defensive driving ...........................................4-2 drunken driving .............................................4-2 control of a vehicle ........................................4-5 braking .............................................

  • Page 258: Your Vehicle

    Your driving, the road, and your vehicle defensive driving the best advice anyone can give about driving is: drive defensively. Please start with a very important safety device in your vehicle: buckle up. See safety belts: they are for everyone on page 1-28 . Defensive driving really means “be ready...

  • Page 259

    Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more ...

  • Page 260

    It’s the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s bac would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower bac level. Ther...

  • Page 261: Caution:

    { caution: drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please don’t drink and drive or ride with a driver who has...

  • Page 262: Braking

    Braking braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That’s perception time. Then you have to bring up your foot and do it. That’s reaction time. Average reaction time is about 3/4 of a second. But that’s only an average. It might b...

  • Page 263

    Anti-lock brake system your vehicle has anti-lock brakes. Abs is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this...

  • Page 264

    The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and c...

  • Page 265: Road Sensing Suspension

    Supplemental brake assist system if your vehicle has vacuum assist power brakes, it is also equipped with a supplemental brake assist system that supplies additional vacuum to the vacuum brake booster if engine vacuum is reduced. Under certain conditions, the supplemental brake assist system may run...

  • Page 266: Stabilitrak

    Stabilitrak ® system your vehicle is equipped with stabilitrak ® , which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you first start your vehicle and begin to drive away, the system ...

  • Page 267

    Stabilitrak ® and part of the traction control system can be turned off or back on by pressing the stabilitrak ® button located on the instrument panel. When the system is turned off, the traction off light will illuminate, and the stability sys disabled message will appear on the dic to warn the dr...

  • Page 268

    Traction control operation the traction control system is part of the stabilitrak ® system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The traction control ...

  • Page 269: Steering

    If your vehicle is in cruise control when the system activates, the stability sys active message will appear on the driver information center and the cruise control will automatically disengage. When road conditions allow you to use cruise again, you may re-engage the cruise control. See “cruise con...

  • Page 270

    The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While you’re in a curve, speed is the one factor you can control. Suppose you’re steering through a sharp curve. Then you suddenly accelerate. Both...

  • Page 271: Off-Road Recovery

    An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straigh...

  • Page 272: Passing

    Passing the driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dange...

  • Page 273: Loss Of Control

    • check your mirrors, glance over your shoulder and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane. (r...

  • Page 274: Vehicle Off Paved Roads

    If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready for a second skid if it occurs. Of course, traction is reduced when water, snow, ice,...

  • Page 275

    Off-road driving can be great fun. But it does have some definite hazards. The greatest of these is the terrain itself. “off-roading” means you’ve left the north american road system behind. Traffic lanes aren’t marked. Curves aren’t banked. There are no road signs. Surfaces can be slippery, rough, ...

  • Page 276: Caution:

    Loading your vehicle for off-road driving there are some important things to remember about how to load your vehicle. • the heaviest things should be on the load floor and forward of your rear axle. Put heavier items as far forward as you can. • be sure the load is secured properly, so driving on th...

  • Page 277

    Environmental concerns off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • always use established trails, roads and areas ...

  • Page 278: Caution:

    Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • you approach things faster and you have less time to scan the terrain for obstacles. • you have less ti...

  • Page 279: Caution:

    When you drive over obstacles or rough terrain, keep a firm grip on the steering wheel. Ruts, troughs or other surface features can jerk the wheel out of your hands if you’re not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground. If this happens, even w...

  • Page 280

    Approaching a hill when you approach a hill, you need to decide if it’s one of those hills that’s just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can ...

  • Page 281: Caution:

    { caution: turning or driving across steep hills can be dangerous. You could lose traction, slide sideways, and possibly roll over. You could be seriously injured or killed. When driving up hills, always try to go straight up. • ease up on your speed as you approach the top of the hill. • attach a f...

  • Page 282

    Q: what should i do if my vehicle stalls, or is about to stall, and i can’t make it up the hill? A: if this happens, there are some things you should do, and there are some things you must not do? First, here’s what you should do: • push the brake pedal to stop the vehicle and keep it from rolling b...

  • Page 283: Caution:

    Driving downhill when off-roading takes you downhill, you’ll want to consider a number of things: • how steep is the downhill? Will i be able to maintain vehicle control? • what’s the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? • are there hidden surface obstacles? Ruts? Logs? B...

  • Page 284

    Q: are there some things i should not do when driving down a hill? A: yes! These are important because if you ignore them you could lose control and have a serious accident. • when driving downhill, avoid turns that take you across the incline of the hill. A hill that’s not too steep to drive down m...

  • Page 285: Caution:

    For reasons like these, you need to decide carefully whether to try to drive across an incline. Just because the trail goes across the incline doesn’t mean you have to drive it. The last vehicle to try it might have rolled over. { caution: driving across an incline that’s too steep will make your ve...

  • Page 286: Caution:

    { caution: getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over, you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path. Driving in mud, sand, snow or ice when y...

  • Page 287: Caution:

    Rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr { caution: driving on frozen lakes, ponds or rivers can be dangerous. Underwater springs, currents under the ice, or sudden thaws can weaken the ice. Your vehicle could fall through the ice and you and your passengers could drown. Drive your...

  • Page 288: Driving At Night

    After off-road driving remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a fire hazard. After operation in mud or sand, have the brake linings cleaned and checked. Theses substances can cause glazing and uneven braking. Check the bo...

  • Page 289

    Here are some tips on night driving. • drive defensively. • don’t drink and drive. • since you can’t see as well, you may need to slow down and keep more space between you and other vehicles. • slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead. • in rem...

  • Page 290

    Driving in rain and on wet roads rain and wet roads can mean driving trouble. On a wet road, you can’t stop, accelerate or turn as well because your tire-to-road traction isn’t as good as on dry roads. And, if your tires don’t have much tread left, you’ll get even less traction. It’s always wise to ...

  • Page 291: Caution:

    Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can’t, try to slow down before you hit them. { caution: wet brakes can cause accidents. They won’t work as well in a quick st...

  • Page 292: Caution:

    Hydroplaning hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you’re going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. Hydroplaning doesn’t hap...

  • Page 293: City Driving

    Some other rainy weather tips • turn on your low-beam headlamps – not just your parking lamps – to help make you more visible to others. • besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle. Allow yourself more clear room ahead, and be ...

  • Page 294: Freeway Driving

    Here are ways to increase your safety in city driving: • know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. • try to use the freeways that rim and crisscross most large cities. You’ll save ti...

  • Page 295

    The most important advice on freeway driving is: keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traffic flow. Treat the left lane on a freeway as a passing lane. At the entrance, there is usually...

  • Page 296

    Before leaving on a long trip make sure you’re ready. Try to be well rested. If you must start when you’re not fresh — such as after a day’s work — don’t plan to make too many miles that first part of the journey. Wear comfortable clothing and shoes you can easily drive in. Is your vehicle ready for...

  • Page 297: Highway Hypnosis

    Highway hypnosis is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, t...

  • Page 298: Hill And Mountain Roads

    Hill and mountain roads driving on steep hills or mountains is different from driving in flat or rolling terrain. If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. See operating your all-wheel-drive ve...

  • Page 299: Caution:

    { caution: coasting downhill in neutral (n) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they wouldn’t work well. You would then have poor braking or even none going down a hill. You could crash. Always have your engine r...

  • Page 300

    Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth and a couple of reflective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of...

  • Page 301

    Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. See stabilitrak ® system on page 4-10 and “rocking your vehicle” under if you are stuck: in sand, mud, ice or snow on page 4-48 . Your an...

  • Page 302

    Here are some things to do to summon help and keep yourself and your passengers safe: • turn on your hazard flashers. • tie a red cloth to your vehicle to alert police that you’ve been stopped by the snow. • put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothin...

  • Page 303: Caution:

    { caution: snow can trap exhaust gases under your vehicle. This can cause deadly co (carbon monoxide) gas to get inside. Co could overcome you and kill you. You can’t see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any...

  • Page 304: Or Snow

    If you are stuck: in sand, mud, ice or snow in order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution. { caution: if you let your ti...

  • Page 305: Caution:

    Using the recovery hooks your vehicle may be equipped with recovery hooks. The recovery hooks are provided at the front of your vehicle. You may need to use them if you’re stuck off-road and need to be pulled to some place where you can continue driving. { caution: these hooks, when used, are under ...

  • Page 306: Towing

    Towing towing your vehicle consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See roadside service on page 7-6 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see recreational vehicle ...

  • Page 307: Loading Your Vehicle

    Loading your vehicle the certification/tire label is found on the rear edge of the driver’s door. The label shows the size of your original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle. This is called the gvwr (gross vehicle weight rating). The gvwr in...

  • Page 308: Caution:

    Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way. If you put things inside your vehicle – like suitcases, tools, packages, or anything else – they go as fast as the vehicle goes. If you have ...

  • Page 309: Trailer Recommendations

    Automatic level control the automatic level control rear suspension comes as a part of the road sensing suspension. See road sensing suspension on page 4-9 . This type of level control is fully automatic and will provide a better leveled riding position as well as better handling under a variety of ...

  • Page 310: Towing A Trailer

    Towing a trailer { caution: if you don’t use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured. You may also damage your v...

  • Page 311

    If you do decide to pull a trailer if you do, here are some important points: • there are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving. A good source for this informat...

  • Page 312

    Tow/haul mode the tow/haul feature assists when pulling a heavy trailer or a large or heavy load. The purpose of the tow/haul mode is to: • reduce the frequency and improve the predictability of transmission shifts when pulling a heavy trailer or a large or heavy load • provide the same solid shift ...

  • Page 313

    Weight of the trailer how heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on...

  • Page 314

    Weight of the trailer tongue the tongue load (a) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The gross vehicle weight (gvw) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in ...

  • Page 315

    Total weight on your vehicle’s tires be sure your vehicle’s tires are inflated to the upper limit for cold tires. You’ll find these numbers on the certification label at the rear edge of the driver’s door or see “tire loading”. Then be sure you don’t go over the gvw and rear axle limits for your veh...

  • Page 316: Caution:

    Driving with a trailer { caution: if you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (co) could come into your vehicle. You can’t see or smell co. It can cause unconsciousness or death. See “engine exhaust” in the index. To maximize your safety when towing ...

  • Page 317

    Following distance stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing you’ll need more passing distance up ahead when you’re towing a trailer. And, becau...

  • Page 318: Caution:

    Driving on grades reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift down, you might have to use your brakes so much that they would get hot and no longer work well. You can tow in drive (d). You may want to shift the transmission to third (3) ...

  • Page 319

    When you are ready to leave after parking on a hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have some...

  • Page 320

    Trailer wiring harness heavy-duty trailer wiring package your vehicle is equipped with the seven-wire trailer towing harness.This harness with a seven-pin universal heavy-duty trailer connector is attached to a bracket on the hitch platform. The center high-mounted stoplamp (chmsl) wire is tied next...

  • Page 321: Section 5

    Service ............................................................5-3 doing your own service work .........................5-3 adding equipment to the outside of your vehicle ......................................................5-4 fuel ...............................................................

  • Page 322: Section 5

    Tires ..............................................................5-66 inflation -- tire pressure ................................5-67 tire inspection and rotation ...........................5-68 when it is time for new tires .......................5-69 buying new tires ..............................

  • Page 323: Service

    Service your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine gm parts and gm-trained and supported service people. We hope you’ll want to keep your gm vehicle all gm. Genuine gm parts have one of these ...

  • Page 324: Your Vehicle

    Caution: (continued) • be sure to use the proper nuts, bolts and other fasteners. “english” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt. Adding equipment to the outside of your vehicle things you might add to the...

  • Page 325: Gasoline Specifications

    Gasoline specifications it is recommended that gasoline meet specifications which were developed by the american automobile manufacturers association and endorsed by the canadian vehicle manufacturers association for better vehicle performance and engine protection. Gasoline meeting these specificat...

  • Page 326: Additives

    Additives to provide cleaner air, all gasolines in the united states are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel. Gasolines containi...

  • Page 327: Filling Your Tank

    Filling your tank { caution: fuel vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if you’re near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel. The fuel cap is located behind a hinged door on the driver’s sid...

  • Page 328: Caution:

    While refueling, hang the fuel cap by the tether using the hook located on the inside of the filler door. To remove the fuel cap, turn it slowly to the left (counterclockwise). { caution: if you get fuel on yourself and then something ignites it, you could be badly burned. Fuel can spray out on you ...

  • Page 329: Caution:

    When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See malfunc...

  • Page 330: Checking Things Under

    Checking things under the hood { caution: things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that w...

  • Page 331

    2. Then go to the front of the vehicle and pull up on the secondary hood release, located near the center of the grill. 3. Lift the hood. 5-11.

  • Page 332

    Engine compartment overview when you open the hood on the 6000 h.O. Engine (5300 similar), you will see: 5-12.

  • Page 333

    A. Engine air cleaner/filter. See engine air cleaner/filter on page 5-19 . B. Coolant surge tank. See cooling system on page 5-30 and coolant surge tank pressure cap on page 5-27 . C. Air filter restriction indicator (if equipped). See engine air cleaner/filter on page 5-19 . D. Engine oil fill. See...

  • Page 334: Engine Oil

    Engine oil if the check oil level message appears on the instrument cluster, it means you need to check your engine oil level right away. For more information, see “check oil level” under dic warnings and messages on page 3-62 . You should check your engine oil level regularly; this is an added remi...

  • Page 335

    When to add engine oil if the oil is at or below the cross-hatched area at the tip of the dipstick, then you’ll need to add at least one quart of oil. But you must use the right kind. This part explains what kind of oil to use. For engine oil crankcase capacity, see capacities and specifications on ...

  • Page 336

    What kind of engine oil to use oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the american petroleum institute (api). Do not use any oil which does not carry this starburst symbol. If you choose to per...

  • Page 337

    As in the chart shown previously, sae 5w-30 is the only viscosity grade recommended for your vehicle. You should look for and use only oils which have the api starburst symbol and which are also identified as sae 5w-30. If you cannot find such sae 5w-30 oils, you can use an sae 10w-30 oil which has ...

  • Page 338

    However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer has gm-trained service people who will perform this work using genuine gm parts and reset the system. It is also important to check your oil regularly and keep it at the pr...

  • Page 339: Engine Air Cleaner/filter

    Engine air cleaner/filter see engine compartment overview on page 5-12 for location of engine air cleaner/filter and change indicator (if equipped). When to inspect if your vehicle is equipped with a filter change indicator it lets you know when the filter needs to be replaced. Vehicles with a restr...

  • Page 340: Caution:

    1. Loosen the screws on the cover of the housing and lift up the cover. 2. Remove the air cleaner/filter from the housing. Care should be taken to dislodge as little dirt as possible. 3. Clean the filter sealing surface and the housing. 4. Install the new engine air cleaner/filter. 5. Reinstall the ...

  • Page 341

    Automatic transmission fluid when to check and change a good time to check your automatic transmission fluid level is when the engine oil is changed. Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: • in heavy city...

  • Page 342

    Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°f (10°c). If it’s colder than 50°f (10°c), drive the vehicle in third (3) until the engine temperature gage moves and then remains steady for 10 minutes. A cold fluid check can be made after the vehicl...

  • Page 343

    3. Check both sides of the dipstick, and read the lower level. The fluid level must be in the cold area, below the cross-hatched area, for a cold check or in the hot area or cross-hatched area for a hot check. Be sure to keep the dipstick pointed down to get an accurate reading. 4. If the fluid leve...

  • Page 344: Engine Coolant

    Engine coolant the cooling system in your vehicle is filled with dex-cool ® engine coolant. This coolant is designed to remain in your vehicle for 5 years or 150,000 miles (240 000 km), whichever occurs first, if you add only dex-cool ® extended life coolant. The following explains your cooling syst...

  • Page 345: Caution:

    What to use use a mixture of one-half clean, drinkable water and one-half dex-cool ® coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. { caution: adding only plain water to your cooling system can be dangerous. Plain water, or some other...

  • Page 346: Caution:

    Checking coolant the coolant surge tank is located in the engine compartment on the passenger’s side of the vehicle. See engine compartment overview on page 5-12 for more information on location. { caution: turning the surge tank pressure cap when the engine and radiator are hot can allow steam and ...

  • Page 347: Caution:

    Adding coolant if you need more coolant, add the proper dex-cool ® coolant mixture at the surge tank , but only when the engine is cool. { caution: you can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Don’t...

  • Page 348: Engine Overheating

    Engine overheating you will find a coolant temperature gage on your vehicle’s instrument panel cluster. See engine coolant temperature gage on page 3-43 . In addition, you will find a low coolant, engine coolant hot, engine overheated and a reduced engine power message in the dic on the instrument p...

  • Page 349: Caution:

    { caution: steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you op...

  • Page 350: Cooling System

    If you get the overheat warning with no sign of steam, try this for a minute or so: 1. Turn on your heater to full hot at the highest fan speed and open the window as necessary. 2. If you’re in a traffic jam, shift to neutral (n); otherwise, shift to the highest gear while driving – drive (d). If yo...

  • Page 351: Caution:

    The coolant level should be at or above the full cold mark. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. { caution: heater and radiator hoses, and other engine parts, can be very hot. Don’t ...

  • Page 352: Caution:

    How to add coolant to the coolant surge tank if you haven’t found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level isn’t at or above the full cold mark, add a 50/50 mixture of clean, drinkable water and dex-cool ® coolant at the coolant...

  • Page 353: Caution:

    { caution: adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your eng...

  • Page 354

    1. Park the vehicle on a level surface. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise (left) about one full turn. If you hear a hiss, w...

  • Page 355

    3. Then fill the coolant surge tank with the proper mixture, to the full cold mark. 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. By this time, the coolant level inside th...

  • Page 356: Engine Fan Noise

    5. Then replace the pressure cap. Be sure the pressure cap is hand-tight and fully seated. Engine fan noise your vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the fan is spinnin...

  • Page 357

    When to check power steering fluid it is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. See engine compartment overview ...

  • Page 358: Windshield Washer Fluid

    Windshield washer fluid what to use when you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. See engi...

  • Page 359: Brakes

    Brakes brake fluid your brake master cylinder reservoir is filled with dot-3 brake fluid. See engine compartment overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down t...

  • Page 360: Caution:

    Checking brake fluid you can check the brake fluid without taking off the cap. Just look at the brake fluid reservoir. The fluid level should be above min. If it isn’t have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is a...

  • Page 361: Caution:

    Notice: • using the wrong fluid can badly damage brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they’ll have to be replaced. Don’t let someone put in the wrong kind of fluid. • if you spill ...

  • Page 362

    Brake pedal travel see your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake adjustment every time you make a brake stop, your disc brakes adjust for wear. Replacing brake system parts the brakin...

  • Page 363: Battery

    Battery your new vehicle comes with a maintenance free acdelco ® battery. When it’s time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an acdelco ® battery. See engine compartment overview on page 5-12 for battery location. Warning: ba...

  • Page 364: Jump Starting

    Jump starting if your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. But please use the following steps to do it safely. { caution: batteries can hurt you. They can be dangerous because: • they contain acid that can burn you. • they contain ga...

  • Page 365

    Notice: if you leave your radio on, it could be badly damaged. The repairs wouldn’t be covered by your warranty. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or accessory power outlets. Turn off the radio and all lamps that aren’t neede...

  • Page 366: Caution:

    The remote negative ( − ) terminal is located on the engine accessory drive bracket and is marked gnd. See engine compartment overview on page 5-12 for more information on location. { caution: using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some h...

  • Page 367: Caution:

    { caution: fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the ot...

  • Page 368

    8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery. Use a remote negative ( − ) terminal if the vehicle has one. Your vehicle’s remote negative ( − ) terminal is marked gnd. Don’t let the other end touch anything until the next step. The other end of the...

  • Page 369

    A. Heavy, unpainted metal engine part or remote negative ( − ) terminal. B. Good battery or remote positive (+) and negative ( − ) terminals. C. Dead battery or remote positive (+) terminal. To disconnect the jumper cables from both vehicles do the following: 1. Disconnect the black negative ( − ) c...

  • Page 370: All-Wheel Drive

    All-wheel drive lubricant checks in this section also apply to these vehicles. However, there are two additional systems that need lubrication. Transfer case when to check lubricant refer to the maintenance schedule to determine how often to check the lubricant. See part c: periodic maintenance i ns...

  • Page 371: Rear Axle

    Rear axle when to check lubricant refer to the maintenance schedule to determine how often to check the lubricant. See part a: scheduled maintenance services on page 6-4 . How to check lubricant to get an accurate reading, the vehicle should be on a level surface. The proper level is from 5/8 inch t...

  • Page 372: Front Axle

    Front axle when to check and change lubricant refer to the maintenance schedule to determine how often to check the lubricant and when to change it. See part a: scheduled maintenance services on page 6-4 . How to check lubricant to get an accurate reading, the vehicle should be on a level surface. I...

  • Page 373: Headlamp Aiming

    Headlamp aiming your vehicle has a visual optical headlamp aiming system equipped with horizontal aim indicators. The aim has been preset at the factory and should need no further adjustment. This is true even though your horizontal aim indicators may not fall exactly on the “0” (zero) marks on thei...

  • Page 374: Headlamp Horizontal Aiming

    The headlamp aiming devices are under the hood near the headlamps. If you believe your headlamps need horizontal (h)(left/right) adjustment, follow the horizontal aiming procedure. If you believe your headlamps need only vertical (v) (up/down) adjustment, follow only the vertical aiming procedure. A...

  • Page 375: Headlamp Vertical Aiming

    Headlamp vertical aiming notice: horizontal aiming must be performed before making any adjustments to the vertical aim. Adjusting the vertical aim first will result in an incorrect headlamp aim. 1. Find the aim dot on the lens of the low beam lamps. 2. Measure the distance from the ground to the aim...

  • Page 376

    4. Turn on the low-beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being aimed. This should allow only the beam of light from the headlamp being aimed to be seen on the flat surface. Notice: do not cover a headlamp to improve beam cut-off when aiming. Coverin...

  • Page 377: Bulb Replacement

    Bulb replacement see replacement bulbs on page 5-64 for the proper type of bulbs to use. For any bulb changing procedure not listed in this section, contact your dealer. High intensity discharge (hid) lighting { caution: the low beam high intensity discharge lighting system operates at a very high v...

  • Page 378: Headlamps

    Headlamps a. Low-beam headlamp (hid) b. Daytime running lamp c. Sidemarker lamp d. High-beam headlamp e. Front parking and turn signal lamp 1. Open the hood of the vehicle. 2. Pry up the eight fastener plugs on the radiator cover and pull the fasteners out. 3. Lift off the radiator cover. 5-58.

  • Page 379

    4. Pull the top left or right corner of the grill out so the clips release. This will give you the needed clearance for removing the headlamp assembly. 5. Remove the horizontal pin from the headlamp assembly by lifting the end of the pin upward until it unsnaps and then pulling it toward the center ...

  • Page 380

    6. Remove the vertical pin from the headlamp assembly by turning the end of the pin away from you until it unsnaps and then pulling it upward. 7. Remove the headlamp assembly by lifting it up and then pulling it out and away from the front of the vehicle. 8. Disconnect the electrical connector from ...

  • Page 381

    16. Place the headlamp assembly back into the vehicle, being sure to align the lower locator tab with the pocket on the vehicle (see arrow). Push the headlamp assembly straight in and then down into position. 17. Install the two pins and snap the ends into their locked position. 18. Reinstall the gr...

  • Page 382: Daytime Running Lamps

    Front turn signal, sidemarker and daytime running lamps a. Low-beam headlamp b. Daytime running lamp c. Sidemarker lamp d. High-beam headlamp e. Front turn signal lamp 1. Remove the headlamp assembly as described previously. 2. Remove the rubber, circular-shaped bulb cap for the affected bulb from t...

  • Page 383: (Chmsl)

    Center high-mounted stoplamp (chmsl) it is recommended that this component be replaced as a unit. Taillamps a. Turn signal-taillamp b. Stop-taillamp c. Back-up lamp d. Sidemarker lamp 1. Use a screwdriver to remove the two screws from the lamp assembly. 2. Remove the lamp assembly. 3. Press the rele...

  • Page 384: Replacement Bulbs

    4. Pull the bulb straight out from the socket. 5. Press a new bulb into the socket, insert it into the taillamp housing and turn the socket clockwise into the taillamp housing until it clicks. The sidemarker lamp does not have a release tab and therefore will not click when it is installed. 6. Reins...

  • Page 385: Windshield Wiper Blade

    Windshield wiper blade replacement windshield wiper blades should be inspected at least twice a year for wear and cracking. See wiper blade check under at least twice a year on page 6-12 for more information. Replacement blades come in different types and are removed in different ways. For proper ty...

  • Page 386: Tires

    Tires your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your cadillac warranty booklet for details. { caution: poorly maintained and improperly used tires are dangerous. • overloadi...

  • Page 387

    Inflation -- tire pressure the certification/tire label, which is on the rear edge of the driver’s door, shows the correct inflation pressures for your tires when they’re cold. “cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Notice: don’t l...

  • Page 388

    Tire inspection and rotation tires should be rotated every 7,500 miles (12,500 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See when it is time for new tires on page 5-69 and wheel replacement on page ...

  • Page 389: Caution:

    { caution: rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can u...

  • Page 390: Buying New Tires

    Buying new tires to find out what kind and size of tires you need, look at the certification/tire label. The tires installed on your vehicle when it was new had a tire performance criteria specifications (tpc spec) number on each tire’s sidewall. When you get new tires, get ones with that same tpc s...

  • Page 391: Caution:

    { caution: if you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. Uniform tire quality grading quality grades can be found ...

  • Page 392

    Traction – aa, a, b, c the traction grades, from highest to lowest, are aa, a, b, and c. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction per...

  • Page 393: Wheel Replacement

    Wheel replacement replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any...

  • Page 394: Caution:

    Used replacement wheels { caution: putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new gm original equipment wheel. Tire chains { caution: don’t use tire ...

  • Page 395: If A Tire Goes Flat

    If a tire goes flat it’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: if a f...

  • Page 396: Changing A Flat Tire

    Changing a flat tire if a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. { caution: changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people. You and they could be badly inj...

  • Page 397

    Removing the spare tire and tools a. Tool kit with jack tools and gloves b. Retaining bracket and wing nut c. Wing nut holding tire blocks d. Tire blocks e. Bottle jack a. Bottle jack b. Wheel blocks c. Wing nut holding tire blocks d. Mounting bracket e. Removable tray f. Retaining hook g. Retaining...

  • Page 398

    For escalade, the equipment is located behind the left trim panel in the rear of the vehicle. Unlatch the release lever to open the trim panel door. Skip the first step and follow the last three. For escalade esv, the equipment you’ll need is under the storage tray in the left trim panel. 1. Remove ...

  • Page 399

    2. Assemble the wheel wrench (h) and the two jack handle extensions (i) as shown. 3. Insert the hoist end (open end) (f) of the extension through the hole (g) in the rear bumper. Be sure the hoist end of the extension connects to the hoist shaft (e). The ribbed square end of the extension is used to...

  • Page 400

    The wheel wrench has a hook that allows you to pull the hoist cable towards you to assist in reaching the spare tire. 5. When the tire has been lowered, tilt the retainer (d) at the end of the cable so it can be pulled up through the wheel opening. 6. Put the spare tire near the flat tire. Removing ...

  • Page 401

    1. Remove the center cap by placing the chisel end of the wheel wrench in the slot on the wheel and gently prying the cap out. 2. Use the wheel wrench to loosen all the wheel nuts. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Don’t remove the wheel nuts yet. 5-81.

  • Page 402: Caution:

    These locations for the front (a) and rear (b) are the general area of jack placement. See text and art following for the exact jack placement. { caution: getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get unde...

  • Page 403

    Front tire flat: if the flat tire is on a front tire of the vehicle, you’ll need to use the jack handle (c) and only one jack handle extension (d). Attach the wheel wrench to the jack handle extension. Attach the jack handle to the jack. Position the jack on the frame behind the flat tire where the ...

  • Page 404: Caution:

    4. Remove all the wheel nuts and take off the flat tire. 5. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. { caution: rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and ...

  • Page 405: Caution:

    6. After mounting the spare, put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub. 7. Turn the wheel wrench counterclockwise to lower the vehicle. Lower the ...

  • Page 406: Caution:

    Storing a flat or spare tire, jack and tools { caution: storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Notice: an aluminum wheel with ...

  • Page 407

    2. Tilt the retainer (d) downward and through the wheel opening. Make sure the retainer is fully seated across the underside of the wheel. 3. Attach the wheel wrench (h) and extensions (i) together. 4. Insert the hoist end (f) through the hole (g) in the rear bumper and into the hoist shaft. 5. Rais...

  • Page 408

    7. Make sure the tire is stored securely. Push, pull and then try to rotate or turn the tire. If the tire moves, use the wheel wrench to tighten the cable. Reinstall the spare tire lock (if equipped). To store the tools, follow these procedures: for escalade, do the following: 1. Put the tool kit, w...

  • Page 409

    4. Use the retaining clip to fasten the tool kit on the stud in the storage compartment in the rear left trim panel and turn the wing nut clockwise to secure. 5. Return the storage tray. A. Tool kit with jack tools and gloves b. Retaining bracket and wing nut c. Wing nut holding tire blocks d. Tire ...

  • Page 410: Caution:

    Secondary latch system your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It’s designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down. See “s...

  • Page 411

    4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with step 5 of “removing the spare tire and tools” earlier in this section. 5. Turn the wrench counterclockwise until approximately six inches (15 cm) of cable is exposed. 6. Stand the wheel blocks on their...

  • Page 412: Caution:

    8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle towards the front of the rear bumper. Position the center lift point of the jack under the center of the spare tire. 9. Turn the wrench clockwise to raise the jack until it lifts...

  • Page 413: Spare Tire

    13. Tilt the retainer at the end of the cable and pull it through the wheel opening. Pull the tire out from under the vehicle. 14. If the cable is hanging under the vehicle, turn the wheel wrench clockwise to raise the cable back up. Have the hoist assembly inspected as soon as you can. You will not...

  • Page 414: Appearance Care

    Appearance care remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be...

  • Page 415

    Here are some cleaning tips: • always read the instructions on the cleaner label. • clean up stains as soon as you can — before they set. • carefully scrape off any excess stain. • use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. • if a ...

  • Page 416: Care Of Safety Belts

    Cleaning wood panels use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth. Cleaning the speaker covers vacuum around a speaker cover gently, so that the speaker won’t be damaged. Clean spots with just water and mild soap. Cleaning...

  • Page 417: Vehicle

    Cleaning the outside of your vehicle the paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing your vehicle the best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in t...

  • Page 418

    Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Protecting exterior bright metal parts bright metal parts shou...

  • Page 419: Sheet Metal Damage

    Cleaning aluminum or chrome-plated wheels your vehicle may be equipped with either aluminum or chrome-plated wheels. Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. The...

  • Page 420: Finish Damage

    Finish damage any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials avaliable from your dealer. Larger areas of finish dama...

  • Page 421

    Vehicle care/appearance materials (cont’d) description usage white sidewall tire cleaner removes soil and black marks from whitewalls. Vinyl cleaner cleans vinyl tops, upholstery and convertible tops. Glass cleaner removes dirt, grime, smoke and fingerprints. Chrome and wire wheel cleaner removes di...

  • Page 422: Vehicle Identification

    Vehicle identification vehicle identification number (vin) this is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The vin also appears on the ...

  • Page 423: Windshield Wiper Fuses

    Windshield wiper fuses the windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed. Power...

  • Page 424

    Fuses usage rr wiper rear window wiper switch seo accy special equipment option accessory ws wpr windshield wipers fuses usage tbc accy truck body controller accessory ign 3 ignition, heated seats 4wd four-wheel drive system htr a/c climate control system lock power door lock relay (lock function) h...

  • Page 425

    Fuses usage driver unlock power door lock relay (driver’s door unlock function) ign 0 pcm, tcm tbc ign 0 truck body controller veh chmsl vehicle and trailer high mounted stoplamp lt trlr st/trn left turn signal/stop trailer lt trn left turn signals and sidemarkers veh stop vehicle stoplamps, brake m...

  • Page 426

    Center instrument panel fuse block the center instrument panel utility block is located underneath the instrument panel, to the left of the steering column. Device usage seo special equipment option trailer trailer brake wiring upfit upfitter (not used) sl ride ride control harness connection hdlr 2...

  • Page 427

    Underhood fuse block the underhood fuse block in the engine compartment on the driver’s side of the vehicle near the battery. Lift the cover for access to the fuse/relay block. To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out. See engine compartment...

  • Page 428

    5-108.

  • Page 429

    *1 — gasoline engine and fuel injection rail #2. *2 — gasoline engine and fuel injection rail #1. *3 — gasoline engine; oxygen sensors. *4 — gasoline engine; oxygen sensors. *5 — pcm ignition fuses usage glow plug not used cust feed accessory power stud #1 auxiliary power mbec mid bussed electrical ...

  • Page 430

    Fuses usage sunroof sunroof seo b2 off-road lamps 4ws vent solenoid canister/quadrasteer module power rr hvac rear climate control aux pwr auxiliary power outlet — console ign 1 ignition relay pcm 1 powertrain control module etc/ecm electronic throttle control, electronic brake controller ign e inst...

  • Page 431

    Fuses usage ipc/dic instrument panel cluster/driver information center hvac/ecas climate control controller cig ltr cigarette lighter hi hdlp-rt high beam headlamp-right hdlp-low headlamp low beam relay a/c comp air conditioning compressor a/c comp air conditioning compressor relay rr wpr rear wiper...

  • Page 432

    Capacities and specifications please refer to part d: recommended fluids and lubricants on page 6-18 for more information. See refrigerant charge label under the hood for charge capacity information and requirements. Capacities and specifications engine vin code spark plug gap vortec™ 5300 v8 t 0.06...

  • Page 433

    Application capacities english metric after refill, the level must be rechecked. Add enough engine oil so that the fluid is within the proper operating range. See engine oil on page 5-14 . Fuel tank capacity escalade escalade esv 26.0 gallons 31.0 gallons 98.0 l 117.0 l air conditioning refrigerant ...

  • Page 434

    Normal maintenance replacement parts replacement part numbers listed in this section are based on the latest information available at the time of printing, and are subject to change. If a part listed in this manual is not the same as the part used in your vehicle when it was built, or if you have an...

  • Page 435: Section 6

    Maintenance schedule ......................................6-2 introduction ...................................................6-2 your vehicle and the environment ....................6-2 maintenance requirements ..............................6-2 how this section is organized ..........................

  • Page 436: Maintenance Schedule

    Maintenance schedule introduction important: keep engine oil at the proper level and change as recommended. Have you purchased the gm protection plan? The plan supplements your new vehicle warranties. See your warranty and owner assistance booklet or your dealer for details. Your vehicle and the env...

  • Page 437: Caution:

    How this section is organized this maintenance schedule is divided into five parts: “part a: scheduled maintenance services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your ...

  • Page 438: Services

    Part a: scheduled maintenance services this part contains engine oil and chassis lubrication scheduled maintenance which explains the engine oil life system and how it indicates when to change the engine oil and filter. Lubricate chassis components with each oil change. Also, listed are scheduled ma...

  • Page 439: Scheduled Maintenance

    Scheduled maintenance the services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 mi...

  • Page 440

    It is also important to check your oil regularly and keep it at the proper level. If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed. See engine oil on page 5-14 fo...

  • Page 441

    22,500 miles (37 500 km) ❑ check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. ❑ rotate tires. See tire inspection and rotation on page 5-68 for proper rotation pattern and additional information. (see footnote +.) 30,000 miles (50 00...

  • Page 442

    50,000 miles (83 000 km) ❑ change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: − in heavy city traffic where the outside temperature regularly reaches 90°f (32°c) or higher. − in hilly or mountainous terrain. − when doing frequent tra...

  • Page 443

    67,500 miles (112 500 km) ❑ check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. ❑ rotate tires. See tire inspection and rotation on page 5-68 for proper rotation pattern and additional information. (see footnote +.) 75,000 miles (125 ...

  • Page 444

    97,500 miles (162 500 km) ❑ check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. ❑ rotate tires. See tire inspection and rotation on page 5-68 for proper rotation pattern and additional information. (see footnote +.) 100,000 miles (166...

  • Page 445: At Each Fuel Fill

    Part b: owner checks and services listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids...

  • Page 446: At Least Twice A Year

    At least twice a year restraint system check make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from...

  • Page 447: At Least Once A Year

    At least once a year key lock cylinders service lubricate the key lock cylinders with the lubricant specified in part d. Body lubrication service lubricate all hood latch assembly, secondary latch, pivots, spring anchor, release pawl, rear compartment hinges, outer tailgate handle pivot points, latc...

  • Page 448: Caution:

    Automatic transmission shift lock control system check { caution: when you are doing this check, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level s...

  • Page 449: Caution:

    Parking brake and automatic transmission park (p) mechanism check { caution: when you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply th...

  • Page 450: Part C: Periodic

    Part c: periodic maintenance i nspections listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department do these jobs. Make sure any necessary repairs are completed at once. Prope...

  • Page 451: Brake System Inspection

    Engine cooling system inspection inspect the hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace as needed. Clean the outside of the radiator and air conditioning condenser. To help ensure proper operation, a pressure test of the...

  • Page 452: Lubricants

    Part d: recommended fluids and lubricants fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage fluid/lubricant engine oil engine oil with the american petroleum institute certified for gasoline engines starburst symbol of the proper vis...

  • Page 453

    Usage fluid/lubricant front axle propshaft spline or one-piece propshaft spline (two-wheel drive with auto. Trans.) spline lubricant, special lubricant (gm part no. U.S. 12345879, in canada 10953511) or lubricant meeting requirements of gm 9985830. Hood hinges multi-purpose lubricant, superlube (gm ...

  • Page 454

    Part e: maintenance record after the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “owner checks and services” or “periodic maintenance” on the following record pages. Also, you should retain all maintenance rece...

  • Page 455

    Maintenance record (cont’d) date odometer reading serviced by maintenance record 6-21.

  • Page 456

    Maintenance record (cont’d) date odometer reading serviced by maintenance record 6-22.

  • Page 457: Section 7

    Customer assistance information ......................7-2 customer satisfaction procedure ......................7-2 online owner center ......................................7-3 customer assistance for text telephone (tty) users ........................................................7-4 customer as...

  • Page 458: Customer Assistance

    Customer assistance information customer satisfaction procedure your satisfaction and goodwill are important to your dealer and to cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, h...

  • Page 459: Online Owner Center

    The bbb auto line program is an out of court program administered by the council of better business bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the new vehicle limited warranty. Although you may be required to resort to this informal dispute resolution pr...

  • Page 460: Telephone (Tty) Users

    Customer assistance for text telephone (tty) users to assist customers who are deaf, hard of hearing, or speech-impaired and who use text telephones (ttys), cadillac has tty equipment available at its customer assistance center. Any tty user can communicate with cadillac by dialing: 1-800-833-cmcc (...

  • Page 461: With Disabilities

    Overseas – customer assistance please contact the local general motors business unit. Mexico, central america and caribbean islands/countries (except puerto rico and u.S. Virgin islands) – customer assistance general motors de mexico, s. De r.L. De c.V. Customer assistance center paseo de la reforma...

  • Page 462: Roadside Service

    Roadside service cadillac’s exceptional roadside service is more than an auto club or towing service. It provides every cadillac owner with the advantage of contacting a cadillac advisor and, where available, a cadillac trained dealer technician who can provide on-site service. Each technician trave...

  • Page 463: Courtesy Transportation

    Roadside service availability wherever you drive in the united states or canada, an advisor is available to assist you over the phone. A dealer technician, if available, can travel to your location within a 30 mile (50 km) radius of a participating cadillac dealership. If beyond this radius, we will...

  • Page 464

    Plan ahead when possible when your vehicle requires warranty service, you should contact your dealer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer can help minimize your inconvenience. If your vehicle ca...

  • Page 465

    Courtesy rental vehicle when your vehicle is unavailable due to overnight warranty repairs, your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained, at actual cost, up to a maximum of $37.00 per day supported by receipts. This requires...

  • Page 466: Reporting Safety Defects

    Reporting safety defects reporting safety defects to the united states government if you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa), in addition to notifying...

  • Page 467: Information

    Service publications ordering information service manuals service manuals have the diagnosis and repair information on engines, transmission, axle, suspension, brakes, electrical, steering, body, etc. Retail sell price: $120.00 transmission, transaxle, transfer case unit repair manual this manual pr...

  • Page 468

    Owner’s information owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the maintenance schedule for all models. Owner’s manual retail sell price: $25.00 current and past model order forms ser...

  • Page 469

    A accessory power outlets ................................. 3-23 adding washer fluid ....................................... 5-38 additional program information ........................... 7-9 additives, fuel ................................................. 5-6 add-on equipment .......................

  • Page 470

    Automatic transmission shift lock control system check ............................................. 6-14 automatic transmission ................................... 5-21 fluid .......................................................... 5-21 operation .....................................................

  • Page 471

    Care of (cont.) your cd and dvd player ........................... 3-104 your cd changer ...................................... 3-104 your cds and dvds .................................. 3-104 cargo area door lock switch ........................... 2-10 cargo cover .....................................

  • Page 472

    Cleaning the speaker covers ........................... 5-96 cleaning the top of the instrument panel ........... 5-95 cleaning the windshield, backglass and wiper blades ....................................................... 5-98 cleaning tires ................................................ 5-99...

  • Page 473

    D daytime running lamps .................................. 3-17 defensive driving ............................................. 4-2 defogging and defrosting ................................. 3-30 delayed locking ............................................. 2-10 diversity antenna system ...............

  • Page 474

    Engine oil and chassis lubrication scheduled maintenance ................................................. 6-5 engine oil level check ................................... 6-11 engine overheated .................................. 3-63 engine .......................................................... 5...

  • Page 475

    Fuel (cont.) filling a portable fuel container ..................... 5-9 filling your tank ........................................... 5-7 fuels in foreign countries .............................. 5-6 gage ......................................................... 3-50 gasoline octane ..................

  • Page 476

    Hitches .......................................................... 4-59 homelink transmitter, programming .................. 2-41 homelink ® transmitter .................................... 2-40 hood ............................................................ 5-10 checking things under ...............

  • Page 477

    K key lock cylinders service .............................. 6-13 keyfob x battery low ............................. 3-67 keyless entry system ....................................... 2-4 keys ............................................................... 2-3 l lamps on reminder ........................

  • Page 478

    M maintenance, normal replacement parts .......... 5-114 maintenance schedule ..................................... 6-11 at each fuel fill ......................................... 6-11 at least once a month ................................ 6-11 at least once a year ....................................

  • Page 479

    O odometer ...................................................... 3-36 off-road recovery .......................................... 4-15 oil life reset ............................................ 3-62 oil pressure low ..................................... 3-62 oil .....................................

  • Page 480

    Passenger sensing system .............................. 1-85 passing ................................................. 4-16, 4-61 passlock ® .................................................. 2-19, ii personalization button ..................................... 3-55 personalization, climate controls...

  • Page 481

    Rear seat armrest .......................................... 2-47 rear seat audio controls ................................. 3-97 rear seat audio (rsa) .................................... 3-97 rear seat entertainment system ....................... 3-85 rear seat operation .............................

  • Page 482

    S safety belt ..................................................... 3-36 reminder light ............................................ 3-36 safety belts ................................................... 5-96 care of ...................................................... 5-96 center passenger positio...

  • Page 483

    Service (cont.) engine soon light ....................................... 3-44 publications ordering information ................... 7-11 setting preset ptys (rds only) ....................... 3-76 setting preset stations .................................... 3-73 setting the time ......................

  • Page 484

    T tachometer .................................................... 3-36 taillamps ....................................................... 5-63 temperature and compass display .................... 2-33 testing the alarm ............................................ 2-19 theft-deterrent, radio ............

  • Page 485

    Transmission .................................................. 5-21 fluid, automatic ........................................... 5-21 temperature gage ....................................... 3-43 transportation options ...................................... 7-8 traveling to remote areas ..............

  • Page 486

    Warnings (cont.) other warning devices .................................. 3-7 safety and symbols ......................................... Iii vehicle damage .............................................. Iv washing your vehicle ...................................... 5-97 weatherstrip lubrication .....