1. DL manuals
  2. Cadillac
  3. Automobile
  4. 2008 CTS-V
  5. Owner's Manual

Cadillac 2008 CTS-V Owner's Manual

Manual is about: Automobile

Summary of 2008 CTS-V

  • Page 1

    04akeng40 owner’s manual table of contents how to use this manual ................................ 3 important safety precautions ....................... 5 section 1 instrumentation and controls .................... 21 section 2 seats and restraints ................................... 257 section 3 ...

  • Page 2

    . . . 2 we thank you for choosing a general motors product, and we want to assure you of our continu- ing commitment to your motoring pleasure and satisfaction. This manual should be considered a permanent part of the vehicle. Keep it with the vehicle when sold, to provide the next owner with import...

  • Page 3

    3 . . . When it comes to service, keep in mind that your dealer knows your vehicle best and is committed to your complete satisfaction. Your dealer invites you to return for all of your service needs both during and after the warranty period. Should you have any concern that has not been handled to ...

  • Page 4

    . . . 4 • section 2: seats and restraints next, focus on the center of your vehicle: the seats and safety belts. Information about these features and about your vehicle’s air bag system is cov- ered in section 2. Section 2 also includes any information pertaining to child restraints. • section 3: st...

  • Page 5

    5 . . . How to use this manual - contains information about tire inflation, inspection, rota- tion and replacement - locates and describes your vehicle’s fuses and circuit breakers - contains some bulb replace- ment instructions and specifi- cations - includes major component specifications and capa...

  • Page 6

    . . . 6 important safety precautions caution and notice boxes cautions and notices alert you to conditions that may result in injury, or that may damage your vehicle. Caution means: this can hurt people. Notice means: this can damage your vehicle. Seating position caution do not adjust the driver's ...

  • Page 7

    7 . . . Important safety precautions caution (continued) wearing a safety belt improper- ly could cause serious injury. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones, and you would be less likely ...

  • Page 8

    . . . 8 important safety precautions caution (continued) a pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible throughout the pregnancy. Air bags caution both the safety belt restraint system and the air bag restraint system are designed to best prot...

  • Page 9

    9 . . . Important safety precautions caution (continued) air bags are designed to be used with the safety belts. Even with an air bag, if you are in a crash and not wearing a safety belt, your injuries could be much worse. If you are too close to an inflat- ing air bag, it could seriously injure you...

  • Page 10

    . . . 10 important safety precautions caution (continued) a rear-facing child restraint in the front seat could be pushed into the seatback by the front passenger's air bag if it inflates. A child in a rear-facing child restraint can be seriously injured if this happens. In vehi- cles with the front...

  • Page 11

    11 . . . Important safety precautions caution (continued) it is very dangerous to leave children inside the vehicle for any extended period of time - especially in hot weather. When you leave the vehicle, take your children with you. Vehicles with automatic transmissions caution (continued) if your ...

  • Page 12

    . . . 12 important safety precautions exhaust warnings caution • things that can burn can touch hot exhaust parts under your vehicle and ignite. Don’t park over papers, leaves, dry grass or other things that can burn. • engine exhaust can kill. It contains carbon monoxide (co) gas, which you can’t s...

  • Page 13

    13 . . . Important safety precautions caution (continued) • engine exhaust may also be entering your vehicle if: – your exhaust system sounds strange or different – your vehicle gets rusty underneath – your vehicle has been damaged or improperly serviced – the base of your vehicle, especially your e...

  • Page 14

    . . . 14 important safety precautions caution (continued) flowing or rushing water creates strong forces. If you try to drive through flowing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of flowing water can carry away a smaller vehicle. If t...

  • Page 15

    15 . . . Important safety precautions caution (continued) things you put inside your vehi- cle can strike and injure people in a sudden stop or turn, or in a crash. Put things in the cargo area of your vehicle and try to spread the weight evenly. Never stack things inside the vehicle any higher than...

  • Page 16

    . . . 16 important safety precautions batteries caution vehicle batteries can hurt you. They contain acid and electrici- ty that can burn and gas that can explode or ignite. Use care and follow any applicable instructions when working near a battery. Do not let battery fluid touch your skin. If you ...

  • Page 17

    17 . . . Important safety precautions engine compartment caution steam from an overheated engine can burn you badly. Stay away from the engine if you see or hear steam coming from it. Be careful when working around the engine compart- ment. Some engine parts can get very hot and could burn you. Caut...

  • Page 18

    . . . 18 important safety precautions caution (continued) steam and scalding liquids from a hot cooling system can blow out and burn you badly. Never turn the cap when the engine and cooling system are hot. Changing a flat tire caution changing a tire can cause inju- ry. The vehicle can slip off the...

  • Page 19

    19 . . . Important safety precautions system problems caution driving with the brake warning light on can lead to an accident. Have the brakes checked imme- diately if the brake warning light stays on. Do not keep driving with low oil pressure. Your engine could overheat and may catch on fire. You o...

  • Page 20

    . . . 20 important safety precautions additional safety cautions caution drinking and driving is very dangerous. Your reflexes, perceptions, attentiveness and judgment can be affected by even a small amount of alcohol. You can have a serious, or even fatal collision if you drive after drinking. Plea...

  • Page 21

    21 . . . Section 1 - instrumentation and controls dash- and console-mounted instruments and controls...................................................25 instrument cluster ..........................................28 warning lights ................................................32 driver informati...

  • Page 22

    . . . 22 section 1 - instrumentation and controls rds sound system with hard disc drive .......162 sound controls .............................................162 radio controls ..............................................166 cd/dvd audio player ...................................176 hard disc dri...

  • Page 23

    23 . . . Section 1 - instrumentation and controls mirrors ...........................................................223 outside mirrors.............................................223 inside day/night mirror ................................225 vanity mirrors ...........................................

  • Page 24

    Instrumentation and controls . . . 24 1 2 5 6 3 4 1 7 8 9 1 13 12 10 11 1 26 21 25 24 23 22 21 20 19 14 15 16 18 17 akeng40_cts page 24 wednesday, july 23, 2008 11:47 am.

  • Page 25

    25 . . . – section 1 ■ dash- and console- mounted instruments and controls 1. Air vents 2. Driver information center buttons 3. Instrument panel dimmer control 4. Multifunction lever 5. Instrument cluster 6. Windshield wipers/washer stalk 7. Navigation screen up/down button (if equipped) 8. Stabilit...

  • Page 26

    Instrumentation and controls . . . 26 9 4 8 7 2 5 2 3 6 1 120 150 180 210 240 270 90 60 30 0 akeng40_cts page 26 wednesday, july 23, 2008 11:47 am.

  • Page 27

    27 . . . – section 1 akeng40_cts page 27 wednesday, july 23, 2008 11:47 am.

  • Page 28

    Instrumentation and controls . . . 28 instrument cluster the instrument cluster shown is typical. Your actual cluster may vary depending on the particular options included in your vehicle. The instrument cluster is designed to let you know at a glance how your vehicle is running. For information abo...

  • Page 29

    29 . . . – section 1 4. Driver information center display the driver information center gives you the status of many of your vehicle's systems. The information shown here varies depending upon which system you choose to display. You can change the information using the trip/ fuel information menu or...

  • Page 30

    Instrumentation and controls . . . 30 6. Fuel gage the fuel gage shows how much fuel is in the fuel tank. The fuel gage works only when the ignition switch is on. A chime will also sound if the fuel is low. The arrow on the gage indicates the side of the vehicle where the fuel door is located. 7. Ta...

  • Page 31

    31 . . . – section 1 when the rpm return to normal operating range, the fuel supply will return to normal. Notice do not operate the engine with the tachometer in the shaded warning area, or engine damage may occur. This could lead to costly repairs not covered by your warranty. 8. Oil pressure gage...

  • Page 32

    Instrumentation and controls . . . 32 notice engine damage resulting from improper maintenance is not covered by the new vehicle warranty. See the maintenance schedule for more information. 9. Gear selector position indicator the indicator shows you what position your gear shift lever is in. See sec...

  • Page 33

    33 . . . – section 1 engine oil pressure warning light this light should come on briefly as you turn on the ignition. If the light does not come on when the ignition is turned on, you may have a problem with a fuse or bulb. Have it fixed right away so it will be ready to warn you if there is a probl...

  • Page 34

    Instrumentation and controls . . . 34 notice engine damage resulting from improper maintenance is not covered by the new vehicle warranty. Change the engine oil at the intervals recommended in the maintenance schedule. Charging system light the charging system light monitors the generator and batter...

  • Page 35

    35 . . . – section 1 engine coolant temperature light the light should come on briefly when you start the engine. If the light does not come on, take your vehicle to the dealer for service. If it stays on or comes on while you are driving, there may be a problem with the cooling system. Stop as soon...

  • Page 36

    Instrumentation and controls . . . 36 if the light comes on while you are driving, pull over and stop carefully. The brake pedal may be harder to push or it may go closer to the floor. It may take longer to stop. If the light stays on, have the vehicle towed for service. The brake system should be i...

  • Page 37

    37 . . . – section 1 electric parking brake light (if equipped) note: this feature is only available on cts-v models. This light should come on briefly as you start the engine. If it doesn't come on, then have it fixed so it will be ready to warn you if there's a problem. This light will come on if ...

  • Page 38

    Instrumentation and controls . . . 38 if the light still stays on, or if it comes on again while you're driving, your vehicle needs service. Until you get it fixed, the brakes will still work, but without the antilock feature. If the system senses a problem, a message will appear on the display. See...

  • Page 39

    39 . . . – section 1 if the light stays on, you may be able to correct the malfunction by making sure the fuel cap is properly installed, if you have just refilled the tank with fuel. After a while, if the light does not go off, take the vehicle in for service. Notice if you keep driving your vehicl...

  • Page 40

    Instrumentation and controls . . . 40 if you have recently replaced the battery in your vehicle, or if the battery has run down, the vehicle’s on-board diagnostic system may determine that the vehicle is not ready for inspection. It may take several days of routine driving in order for the diagnosti...

  • Page 41

    41 . . . – section 1 stabilitrak ® /traction control system light this light will go on when you start the engine and may stay on for a few seconds. If it doesn't come on, then have it fixed so it will be ready to warn you if there is a problem. If it stays on or comes on while you are driving, ther...

  • Page 42

    Instrumentation and controls . . . 42 air bag light the air bag light on your instrument cluster flashes when you start the vehicle to indicate that the restraint is in good working order. If it doesn't come on, then have it fixed so it will be ready to warn you if there is a problem. After the syst...

  • Page 43

    43 . . . – section 1 passenger air bag on/off indicator see "automatic occupant sensor system" in section 2. Passenger safety belt reminder light see "safety belts" in section 2 for information. Security system light see "theft deterrent system" in section 3 for more information about this light. Ak...

  • Page 44

    Instrumentation and controls . . . 44 fog lamp light this light will come on when the fog lights are turned on. See "fog lights" later in this section for more information. Rear fog lamp light this light will come on when the rear fog lights are turned on. See "rear fog lights" later in this section...

  • Page 45

    45 . . . – section 1 cruise control light this light turns on whenever you set the cruise control. See "cruise control" later in this section for more information. Low tire pressure light this light comes on briefly as you are starting your engine as a check to show you it is working properly. If th...

  • Page 46

    Instrumentation and controls . . . 46 driver information center the driver information center gives you the status of many of your vehicle's systems. With the driver information center you can customize and display personalization features and warning messages. The control buttons are located on the...

  • Page 47

    47 . . . – section 1 driver information center buttons the control buttons are located on the instrument panel, near the steering wheel. Menu up/down button press the up or down arrow to scroll up or down through a current menu. Trip/fuel information button press this button to access the trip/ fuel...

  • Page 48

    Instrumentation and controls . . . 48 vehicle information button pressing this button repeatedly will allow you to view, reset or turn off certain vehicle information menu items. • engine oil life • english/metric unit selection • enable/disable ultrasonic rear parking assist • tire pressure monitor...

  • Page 49

    49 . . . – section 1 reset button press this button to reset driver information center features and to turn off or acknowledge messages. Trip/fuel information menu press this button to access the trip/ fuel information menu. The bottom line of the display shows the compass. See "compass" later in th...

  • Page 50

    Instrumentation and controls . . . 50 the reading will be indicated in metric units of kilometers or in us-english units of miles. To set a trip odometer to zero, first display the desired trip odometer and then press and hold the button. Only the trip odometer that is displayed will be reset. • fue...

  • Page 51

    51 . . . – section 1 • timer 00:00:00 this feature acts as a stop- watch. The timer function allows you to time how long it takes to get from one point to another. To start the timer, first select its display, then press the button. The timer will start. To stop the timer without reset- ting it, fir...

  • Page 52

    Instrumentation and controls . . . 52 • speedometer in addition to the standard analog speedometer, your vehicle is equipped with a digi- tal speed display. The reading will be indicated in metric units of km/h (kilome- ters per hour) or in us-english units of mph (miles per hour). • blank display a...

  • Page 53

    53 . . . – section 1 units to switch your displays between english and metric units, first select this item, then press the button. Parking assist use this display to enable or disable the ultrasonic rear parking assist feature. To enable or disable this feature, do the following: 1. Press repeatedl...

  • Page 54

    Instrumentation and controls . . . 54 tire pressure monitor displays press repeatedly to display the following: • front tires kpa left xx right xx (front left and right tire pressures) • rear tires kpa left xx right xx (rear left and right tire pressures) these displays show the air pres- sure for e...

  • Page 55

    55 . . . – section 1 press to calibrate compass with the ignition on, the compass reading will appear in the driver information center display. If cal appears in the window, the compass needs calibration. If an incorrect reading is displayed, first check that the compass is set to the correct varian...

  • Page 56

    Instrumentation and controls . . . 56 see "matching transmitters" under "remote keyless entry system" in section 3 for information. If your vehicle is equipped with a keyless access system for both vehicle entry and vehicle ignition and starting functions, see "matching transmitters" under "keyless ...

  • Page 57

    57 . . . – section 1 feature customization the driver information center can be used to program various customization features that may be available with your vehicle. The number of programmable features varies depending on which vehicle options are purchased. Press the button to enter programming m...

  • Page 58

    Instrumentation and controls . . . 58 • remote door lock • remote door unlock • delay door lock • exit lighting • approach lighting • factory settings • advanced features press to enter see "advanced features menu" later in this section for more information. • feature settings press to exit the info...

  • Page 59

    59 . . . – section 1 display language use this menu to select the language that you would like your vehicle to use for information displays. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following language options: • english (english ...

  • Page 60

    Instrumentation and controls . . . 60 auto door lock (automatic door lock) this feature allows you to customize your automatic door locks to suit your needs. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following options: • shift out...

  • Page 61

    61 . . . – section 1 auto door unlock (automatic door unlock) this item allows you to customize your vehicle’s automatic door unlock feature. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following options: • off with this setting act...

  • Page 62

    Instrumentation and controls . . . 62 remote door lock this feature allows you to select the type of feedback you will receive when locking the vehicle using the remote keyless entry or the keyless access transmitters. You will also receive the selected feedback when locking the vehicle using the pa...

  • Page 63

    63 . . . – section 1 remote door unlock (remote door unlock) this feature allows you to select the type of feedback you will receive when unlocking the vehicle using the remote keyless entry or the keyless access transmitters. You will also receive the selected feedback when unlocking the vehicle us...

  • Page 64

    Instrumentation and controls . . . 64 delay door lock you can program your power door locks to delay locking until every- one has gotten out of the vehicle and closed their doors. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the followin...

  • Page 65

    65 . . . – section 1 exit lighting this feature allows you to desig- nate the length of time that the exterior lights stay on (when it is dark outside) after the ignition is turned off. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the fo...

  • Page 66

    Instrumentation and controls . . . 66 approach lighting this feature allows you to program the exterior lights to turn on or remain off when unlocking the vehicle using the remote keyless entry or the keyless access transmitters while it is dark outside. Press the button to enter the submenu. While ...

  • Page 67

    67 . . . – section 1 factory settings this feature allows you to reset all of the system's programmable features to their default settings. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following options: • restore all if you select t...

  • Page 68

    Instrumentation and controls . . . 68 advanced features menu to access additional programmable features, press the button repeatedly until the following message appears on the display: • advanced features press to enter press the button to enter the submenu. Menu items can only be programmed to one ...

  • Page 69

    69 . . . – section 1 keyless locking if your vehicle is equipped with the keyless access system, this item allows you to customize your vehicle’s passive door locking feature. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following op...

  • Page 70

    Instrumentation and controls . . . 70 keyless unlock if your vehicle is equipped with the keyless access system, this item allows you to customize your vehi- cle’s passive door unlock feature. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through...

  • Page 71

    71 . . . – section 1 electronic key reminder if your vehicle is equipped with the keyless access system, this feature allows you to select whether or not the horn will sound to remind you that at least one keyless access transmitter has been left in the vehicle. Press the button to enter the submenu...

  • Page 72

    Instrumentation and controls . . . 72 chime volume this feature allows you to change the chime volume level. The chime cannot be turned off completely. The system has two chime volume levels, normal and loud. Press the button to enter the submenu. While in this submenu, press the button repeatedly t...

  • Page 73

    73 . . . – section 1 while in this submenu, press the button repeatedly to scroll through the following options: • off the outside mirrors do not tilt down when the vehicle is shifted into r (reverse). This is the default setting. • driver mirror the outside mirror on the driver's side of the vehicl...

  • Page 74

    Instrumentation and controls . . . 74 easy exit recall note: this feature may not be available on all vehicles. This feature allows you to enable or disable automatic recall of the memory feature's easy exit position. Press the button to enter the submenu. While in this submenu, press the button rep...

  • Page 75

    75 . . . – section 1 once the desired setting is displayed, press the button to select it. You may now either exit program- ming mode or program the next available feature. To exit programming mode, see "exiting programming mode" later in this section. See the following, later in this section, for m...

  • Page 76

    Instrumentation and controls . . . 76 • seat/tilt with this setting activated, the memory feature’s easy exit position will recall the exit position for the driver’s seat and the tilt position of the steering wheel. • seat/telescope with this setting activated, the memory feature’s easy exit positio...

  • Page 77

    77 . . . – section 1 memory seat recall note: this feature may not be available on all vehicles. This feature allows you to enable or disable automatic recall of memory feature settings. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the f...

  • Page 78

    Instrumentation and controls . . . 78 remote start (vehicle remote- start) this feature allows you to enable or disable the vehicle remote- starter. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the following options: • off with this sett...

  • Page 79

    79 . . . – section 1 gage tracers note: this feature is only available on cts-v models. This feature allows you to enable or disable the tracer lights in the speedometer and tachometer. Press the button to enter the submenu. While in this submenu, press the button repeatedly to scroll through the fo...

  • Page 80

    Instrumentation and controls . . . 80 advanced features press to exit press the button to exit the menu. The system will display feature settings press to exit. Press the button to exit the menu. To return to the beginning of the menu, press the customization button. To exit programming mode, see "e...

  • Page 81

    81 . . . – section 1 compass with the ignition on, the compass reading will appear in the driver information center display. As you are driving, n (north), ne (north east), e (east), se (south east), s (south), sw (south west), w (west) or nw (north west) should appear on the display to show your ve...

  • Page 82

    Instrumentation and controls . . . 82 compass calibration while calibrating the compass, do not operate any power switches. For example, opening or closing the windows or sunroof, moving the seats, adjusting the climate controls or other power features will interfere with compass calibra- tion. To c...

  • Page 83

    83 . . . – section 1 compass variance your vehicle’s compass zone should be pre-set to the region where your vehicle was first sold. If your vehicle is taken outside this zone, it may be necessary to adjust the compass to compensate for variance. See your dealer to find out what zone you are in. To ...

  • Page 84

    Instrumentation and controls . . . 84 driver information center messages these messages will appear if a problem is sensed in one of your vehicle's systems. Press to acknowledge a message and remove it from the display. However, if a message requires immediate action, the message will be displayed u...

  • Page 85

    85 . . . – section 1 • all wheel drive off note: this message may not be available on all vehicles. Appears when a temporary condition exists and the all- wheel drive system has been automatically disabled. The system will switch to two- wheel drive. This message may appear under the following condi...

  • Page 86

    Instrumentation and controls . . . 86 • battery saver active appears if the vehicle detects that the battery voltage is dropping beyond a reasonable point. When the battery voltage drops, the battery saver system will start reducing power to certain features that may not be noticeable. If a feature ...

  • Page 87

    87 . . . – section 1 • calibrating: drive in circles appears while you are calibrat- ing the compass. See "compass calibration" earlier in this section for more information. • calibration complete appears when the compass cal- ibration is complete. See "compass calibration" ear- lier in this section...

  • Page 88

    Instrumentation and controls . . . 88 stop as soon as possible and have the tire pressures checked and corrected. Inflate the tires to the recom- mended pressure. See "tires" in section 4 for more information. Also, see the following for more information: - vehicle information menu tire pressure mon...

  • Page 89

    89 . . . – section 1 • electronic key not detected note: this message may not be available on all vehicles. Appears when the vehicle does not detect the presence of a keyless access transmitter when you attempt to start the vehicle or after a door is closed. This message will also appear when the ve...

  • Page 90

    Instrumentation and controls . . . 90 try moving the transmitter to different locations within the vehicle. If this does not help, place the transmitter in the transmitter pocket in the center console storage area with the buttons facing to the front of the vehicle and then start the engine. • elect...

  • Page 91

    91 . . . – section 1 • engine oil low add oil note: this message may not be available on all vehicles. Appears when the engine oil level is low. Check the oil and add if needed. You may need to let the vehicle cool down or warm up and cycle the ignition for this mes- sage to clear. This message will...

  • Page 92

    Instrumentation and controls . . . 92 • engine power is reduced appears when engine power is being reduced to protect the engine from damage. This also can affect the vehicle's ability to accelerate. There are several malfunctions that might trigger this message. If this message appears with no redu...

  • Page 93

    93 . . . – section 1 • ice possible drive with care appears when the outside temperature is cold enough to create icy road conditions. Adjust your driving accordingly. • learn delay active wait xx min (learn delay active wait xx minutes) note: this message may not be available on all vehicles. Appea...

  • Page 94

    Instrumentation and controls . . . 94 • oil pressure low stop engine appears when the engine oil pressure is low. The engine oil pressure warning light will also appear. Notice continuing to drive your vehicle can result in severe engine damage. If you get a low oil pressure warning, stop the vehicl...

  • Page 95

    95 . . . – section 1 • parking assist off appears when the vehicle is started while the ultrasonic rear parking assist feature is disabled. This is a reminder that the system is off and will not warn you of objects in your path. See the following, earlier in this section, for more information: - veh...

  • Page 96

    Instrumentation and controls . . . 96 • press brake to start engine note: this feature may not be available on all vehicles. If your vehicle is equipped with the keyless access system, this message appears to remind you that the brake pedal must be applied while starting the engine. This feature is ...

  • Page 97

    97 . . . – section 1 • release park brake switch note: this feature is only avail- able on cts-v models. If your vehicle is equipped with the electric parking brake, this message appears when the electric parking brake is applied while the vehicle is in motion. See "parking brake" in section 3 for i...

  • Page 98

    Instrumentation and controls . . . 98 • reset hood see owners manual appears when the pedestrian protection system has raised the rear of the hood. See the following, later in this section, for more information: - pedestrian protection system • right rear door open appears when the right rear door i...

  • Page 99

    99 . . . – section 1 • service all wheel drive note: this feature may not be available on all vehicles. Appears if there is a problem with the all-wheel drive system. The system will switch to two- wheel drive. This message may appear under the following conditions: - the system has overheated. - th...

  • Page 100

    Instrumentation and controls . . . 100 • service brake assist appears if there is a problem with the brake system. Stop as soon as possible and turn the ignition off. Then start the engine to reset the system. If this message continues to appear or reappears while driving, there is a problem with th...

  • Page 101

    101 . . . – section 1 • service parking assist appears if there is a problem with the ultrasonic rear parking assist feature. Do not use the parking assist feature while this message is displayed. See your dealer for service. See the following, later in this section, for more information: - ultrason...

  • Page 102

    Instrumentation and controls . . . 102 • service stabilitrak appears if your stability enhancement system is malfunctioning. The stabilitrak ® /traction control system light will appear on the instrument cluster. To reset the system, stop and turn the ignition off and then back on. If the message st...

  • Page 103

    103 . . . – section 1 • service tire monitor system appears when the tire pressure monitoring system is not working properly. One or more of the tire sensors may be missing or inoperative. Have the vehicle serviced. The low tire pressure warning light will flash then shine steadily for the remainder...

  • Page 104

    Instrumentation and controls . . . 104 • shift to park note: this feature may not be available on all vehicles. Appears when you turn off the engine and the vehicle is not in p (park). The keyless access system will be in the accessory mode. Move the shift lever into p (park), then turn off the igni...

  • Page 105

    105 . . . – section 1 • stabilitrak not ready appears if the stabilitrak system is not ready. The stabilitrak ® /traction control system light will come on to remind you that the system is off. When the system is ready, the message will turn off. See "stabilitrak system" later in this section for mo...

  • Page 106

    Instrumentation and controls . . . 106 • start aborted by theft deterrent note: this feature may not be available on all vehicles. Appears if there is a communi- cation problem between the keyless access system and the vehicle. You will not be able to start the engine. See your dealer for service. •...

  • Page 107

    107 . . . – section 1 • tighten gas cap appears when the gas cap has not been properly installed. Check the gas cap to be sure that it is on properly. • tire learning active appears when the tire pressure monitor system is re-learning the tire positions on your vehicle. For more information, see "ti...

  • Page 108

    Instrumentation and controls . . . 108 lights the main light controls are on the steering column. Additional controls are on the instrument panel. See "lights" and "multifunction lever" later in this section for more information. Heating and air conditioning system your vehicle is equipped with a he...

  • Page 109

    109 . . . – section 1 hood release use the hood release handle, located near the driver's door, to open the hood. See section 4 for more information. Trunk lid lock release with this option you can open the trunk from inside your vehicle. See "trunk area" later in this section. Parking brake release...

  • Page 110

    Instrumentation and controls . . . 110 hazard warning flasher press the flasher button in to make your front and rear turn signal lights flash on and off. It works in whichever position your ignition is in, and even if the engine is turned off. Press the switch again to turn this feature off. ■ trac...

  • Page 111

    111 . . . – section 1 when the system is limiting wheel spin, the stabilitrak ® /traction control system light flashes. You may feel or hear the system working, but this is normal. To help limit wheel spin, you should always leave this system on. However, you can turn this system off if you need to....

  • Page 112

    Instrumentation and controls . . . 112 for more information, see "stabilitrak ® /traction control system light" under "warning lights" earlier in this section. Adding non-gm accessories to your vehicle can affect your vehicle's performance and safety. See the following in section 4 for more informat...

  • Page 113

    113 . . . – section 1 the stabilitrak competitive mode message will appear on the driver information center. See "driver information center messages" earlier in this section for more information. Press the button again to turn the system back on. Otherwise, the system will automatically revert to it...

  • Page 114

    Instrumentation and controls . . . 114 if you use your cts-v model for competitive driving, the brake fluid should be replaced with a high-performance brake fluid that has a dry boiling point greater than 279°c (534°f). Do not use silicone or dot-5 brake fluids. When using high-performance brake flu...

  • Page 115

    115 . . . – section 1 press the tc button to turn the system off. If your vehicle is a cts-v model, the button is located on the steering wheel. Otherwise, the button is located on the instrument panel. The stabilitrak off message will appear on the driver informa- tion center. See "driver informa- ...

  • Page 116

    Instrumentation and controls . . . 116 ■ accessory power outlets outlets can be used to plug in electrical equipment such as a cellular telephone. There are three accessory power outlets. • the front power outlet is located below the heating and air conditioning system. • there is another power outl...

  • Page 117

    117 . . . – section 1 when not in use, always cover the outlet with the protective cap. Certain accessory power plugs may not be compatible with the power outlets in your vehicle. Use of such plugs may result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for more in...

  • Page 118

    Instrumentation and controls . . . 118 ■ lights the main light controls are on the multifunction lever. Additional controls are on the instrument panel. Main light controls the main light controls are on the multifunction lever. Rotate the end of the multifunc- tion lever up to operate the exteri- o...

  • Page 119

    119 . . . – section 1 rotate the control to to turn on your parking and other operating lights. The headlights will not come on. Rotate the control to to turn off all the lights and activate the auto- matic headlight system. When activated, this automatic headlight feature turns your head- lights an...

  • Page 120

    Instrumentation and controls . . . 120 the lights may also turn on when you drive through a low-light area. The lights will turn off when the ignition is turned off. Rotate the band to to turn off the headlights and other operating lights. Headlight high beam flashing this feature lets you flash you...

  • Page 121

    121 . . . – section 1 adaptive forward lighting system the adaptive forward lighting system swivels the headlights horizontally to provide greater road illumination while turning. To enable this feature, set the headlight control to the auto position. Vehicle speed must be greater than 3 km/h (2 mph...

  • Page 122

    Instrumentation and controls . . . 122 headlight washers to wash your headlights, activate the windshield washer while the headlights are on. See "windshield wipers/washer stalk" later in this section for more information. Wiper activated headlights (if equipped) if the automatic lights control is o...

  • Page 123

    123 . . . – section 1 fog lights the fog light control is located on the multifunction lever next to the fog light symbols. Front fog lights rotate the band up to and release it to turn your front fog lights on and off. The band returns to its original position when released. Your vehicle's parking ...

  • Page 124

    Instrumentation and controls . . . 124 rear fog lights rotate the band to and release it to turn your rear fog lights on and off. Your rear fog lights operate only with the parking lights or headlights. The band returns to its original position when released. Curbside parking lights this feature mak...

  • Page 125

    125 . . . – section 1 instrument light dimmer the control is located on the instrument panel to the left of the steering column. The instrument light dimmer controls the brightness of the instrument panel lights. Rotate the knob to the full right position to turn on the interior lights. If the low b...

  • Page 126

    Instrumentation and controls . . . 126 ■ heating and air conditioning system dual zone climate control system the following pages describe how to operate your dual zone climate control system. This electronic, automatic air conditioning system allows the driver and the front seat passenger to indepe...

  • Page 127

    127 . . . – section 1 automatic mode in automatic mode, all you have to do is select a desired temperature setting. The system will automatically control the inside temperature, air delivery mode and the fan speed to achieve your set temperature as quickly as possible. The air conditioning compresso...

  • Page 128

    Instrumentation and controls . . . 128 temperature control driver temperature control press the up or down arrow on the driver’s side to adjust the temperature for the driver’s side. Passenger temperature control press to turn the passenger zone temperature control on and off. Press the up or down a...

  • Page 129

    129 . . . – section 1 manual mode fan speed selector press the up or down arrow on the control with the fan symbol to increase or decrease the fan speed. Fan speed is adjustable in any of this system’s modes. If the system is operating in the automatic mode and the fan speed is adjusted, the system ...

  • Page 130

    Instrumentation and controls . . . 130 this mode divides airflow between the windshield defroster vents, the floor outlets and the side window defroster vents. The recirculation feature will automatically turn off. Use this mode to remove fog from the windshield or side windows. The a/c compressor w...

  • Page 131

    131 . . . – section 1 use this mode in cold weather to remove fog or ice from the windshield. Most of the air is directed through the windshield defroster outlets, with a small amount directed through the side window defogger outlets. The recirculation feature will automatically turn off. The a/c co...

  • Page 132

    Instrumentation and controls . . . 132 air conditioning mode press to override the automatic mode and turn the air conditioning compressor off and on. The system will cool and dehumidify the air inside the vehicle. Press to return to automatic operation. In automatic mode, the air conditioning compr...

  • Page 133

    133 . . . – section 1 sensors in order for the automatic climate control system to work properly, be sure not to cover the sensors. Solar sensor the sensor is located on top of the instrument panel. Temperature sensor the inside temperature sensor is located on the instrument panel, near the steerin...

  • Page 134

    Instrumentation and controls . . . 134 operating tips before using the air conditioning system, open the windows for a few minutes to permit hot air to escape. Close the windows when using the air conditioning system. Only use gm-approved hood deflectors on your vehicle. Keep the area under the fron...

  • Page 135

    135 . . . – section 1 passenger compartment air filter a disposable passenger compartment air filter traps most pollutants from the air entering your vehicle. Change the filter at the intervals recommended in your maintenance schedule booklet. Using the heating and air conditioning system without th...

  • Page 136

    Instrumentation and controls . . . 136 notice added audio or communication equipment could interfere with the operation of the vehicle's engine, radio, or other systems, and could damage them. Check with your dealer before adding any audio or communication equipment. Notice cellular phone usage may ...

  • Page 137

    137 . . . – section 1 dolby ® is manufactured under license from dolby ® laboratories. Dolby ® and the double-d symbol are trademarks of dolby ® laboratories. If your vehicle is equipped with a navigation system, then the radio is integrated into that system's control panel. See the separate manual ...

  • Page 138

    Instrumentation and controls . . . 138 rds sound system with 6-disc cd player (mp3 compatible) sound controls power control press the vol (volume/power) knob to turn the radio on. Press it again to turn the radio off. Volume control rotate the vol (volume/power) knob to the right to increase the vol...

  • Page 139

    139 . . . – section 1 automatic volume control works best when listening at low volume levels. At loud listening levels there will be little or no effect. 1. Adjust the volume to the desired level by rotating the vol (volume/power) knob. 2. Press the config (configure) button to display the radio se...

  • Page 140

    Instrumentation and controls . . . 140 to quickly set a tone control to its middle position, press and hold the push-button under bass, mid (midrange), or treb (treble) for more than two seconds. You will hear one beep. To quickly set all speaker and tone controls to their middle positions, press an...

  • Page 141

    141 . . . – section 1 this setting enables five- channel surround sound when listening to a cd, mp3, or portable audio device (if connected). 3. Press the back button to exit the display. To return to the original display, press the back button repeatedly or just wait for the display to time out. Ad...

  • Page 142

    Instrumentation and controls . . . 142 radio controls finding a station band selection press the fm/am button to change between the am and fm bands. Tuning rotate the tune/tone knob to the right to go to a higher station and to the left to go to a lower station. Station seeking press the seek right ...

  • Page 143

    143 . . . – section 1 local station list press the menu/select knob to display a list of local stations. A speaker symbol appears on the display next to the currently selected source. Rotate the menu/select knob to scroll through the list. Press the knob to select the station. Touch refresh list to ...

  • Page 144

    Instrumentation and controls . . . 144 to store a radio station to a preset list, do the following: 1. Press the fm/am button to change between the am and fm bands. 2. Tune in the station. 3. Press the fav (favorites) button to display one of up to six pages where stations are stored. 4. Press and h...

  • Page 145

    145 . . . – section 1 source selection press cd to switch from the radio to the cd changer. The audio source must be loaded to play. When a cd is playing, disc and track numbers appear on the display. Press fm/am to stop playing the disc and switch to the radio. Press cd to restart the disc. Press a...

  • Page 146

    Instrumentation and controls . . . 146 display control press the info button repeatedly to display an rds station name, frequency, program type or program name (if available). If the button is pressed when information is not available, no info (no information) will appear on the display. Rds feature...

  • Page 147

    147 . . . – section 1 emergency alerts the system will automatically interrupt the audio to bring you local or national emergency broadcasts. Alert appears on the display. Emergency broadcasts are only available when the traffic announcement feature is activated. See the following, later in this sec...

  • Page 148

    Instrumentation and controls . . . 148 if the radio is tuned to an rds station that has traffic announcement broadcast capability while the traffic announcement feature is disabled, ta (traffic announcement) will appear on the display. If the traffic announcement feature is enabled while the radio i...

  • Page 149

    149 . . . – section 1 text messages messages are additional text information that is being broadcast by a station. Press the info (information) button to view the most recent message. If the whole message does not appear on the display, parts of the message will appear every three seconds until the ...

  • Page 150

    Instrumentation and controls . . . 150 if a program type is not selected, press the back button to return to the original display, or just wait for the display to time out. Not all stations support the program type feature. Pressing a program type push- button may not take you to all of the stations...

  • Page 151

    151 . . . – section 1 regionalization if this feature is enabled, the alternate frequency changes are limited by the program identification code. 1. Press the config (configure) button to display the radio setup menu. 2. Press the push-button under rds (radio data system) to display the rds menu. Th...

  • Page 152

    Instrumentation and controls . . . 152 6-disc cd changer with the compact disc changer, you can play up to six discs contin- uously. If the ignition or the radio is turned off, the compact disc will stay in the player. When the ignition and radio are turned on, the compact disc will resume play at t...

  • Page 153

    153 . . . – section 1 loading and removing discs with the compact disc changer, you can play up to six discs continuously. To load one compact disc: 1. Press the load button . 2. When the message appears on the display, insert the cd label side up, partway into the slot. The player will automaticall...

  • Page 154

    Instrumentation and controls . . . 154 playing a compact disc use the volume, tone, and speaker controls just as you do for the radio. Other controls may have different functions when a disc is inserted. Once the disc is inserted, compact disc functions will appear on the display above each push-but...

  • Page 155

    155 . . . – section 1 seeking push the seek right arrow button to move quickly to the beginning of the next track. Push the seek left arrow button to move quickly to the beginning of the current or previous track. If you hold the button down, or if you press it more than once, the player will contin...

  • Page 156

    Instrumentation and controls . . . 156 playing mp3 or wma format cds (6-disc cd changer) the player will recognize mp3 and wma files that were recorded on cd-r or cd-rw discs. The files must have been recorded on the cd at one of the following bit rates: • 32 kbps • 40 kbps • 56 kbps • 64 kbps • 80 ...

  • Page 157

    157 . . . – section 1 if you burn your own mp3 or wma disc on a personal computer: • make sure the mp3/wma files are recorded on a cd-r or cd- rw disc. • do not mix standard audio and mp3/wma files on one disc. • when burning an mp3 disc using multiple sessions, make sure to finalize the disc. It is...

  • Page 158

    Instrumentation and controls . . . 158 root directory the root directory will be treated as a folder. If the root directory contains compressed audio files, the directory will be displayed as f1 disc. All files contained directly under the root directory will be accessed prior to any root directory ...

  • Page 159

    159 . . . – section 1 playlists can be changed by press- ing the next and previous folder buttons, the seek buttons or the fast forward/reverse buttons. When a track from a new folder begins to play, the new track name will be displayed. However, if folder mode has been chosen as the default display...

  • Page 160

    Instrumentation and controls . . . 160 playlists can be changed by press- ing the next and previous folder buttons. Tracks can be changed by using the seek buttons or by rotating the tuner knob. Press the fwd or rev button to move quickly ahead or back to another part of the current track. Playing a...

  • Page 161

    161 . . . – section 1 previous/next folder to move ahead to the first track in the next folder, press the push- button under . To play the first track in the previous folder, press the push- button under . Fast forwarding/rewinding press and hold the fwd or rev button to move quickly ahead or back t...

  • Page 162

    Instrumentation and controls . . . 162 rds sound system with hard disc drive radios with a hard disc drive contain a gracenote ® database that the radio uses to determine the song, artist, album and genre information. Music or content stored on the hard disc drive that you did not create, or have th...

  • Page 163

    163 . . . – section 1 audiopilot ® noise compensation with this feature, the sound system monitors the noise level in the vehicle and automatically adjusts the volume to keep the volume level above the back- ground noise level. This feature works best at lower sound system volume settings, where bac...

  • Page 164

    Instrumentation and controls . . . 164 to quickly set a tone control to its middle position, press and hold the push-button under bass, mid (midrange), or treb (treble) for more than two seconds. You will hear one beep. To quickly set all speaker and tone controls to their middle positions, press an...

  • Page 165

    165 . . . – section 1 the following settings are available when listening to cd or dvd audio sources recorded using 5.1 surround sound processing. - 5.1 surround + normal this mode optimizes the sound for all seating positions. - 5.1 surround + rear this mode optimizes the sound for the rear seat oc...

  • Page 166

    Instrumentation and controls . . . 166 3. After choosing the desired control, rotate the tune/ tone knob to the right or left, press the seek right or left arrow buttons, or press the fwd or rev buttons to increase or decrease the level of the selected control. To quickly set a speaker control to it...

  • Page 167

    167 . . . – section 1 station seeking press the seek right arrow button and the radio will go to the next higher station and stay there. Press the seek left arrow button to go to the previous station and stay there. The radio will only seek to stations that are in the selected band. The radio will n...

  • Page 168

    Instrumentation and controls . . . 168 to select the desired number of "favorites" pages, do the following: 1. Press the config (configure) button to display the radio setup menu. 2. Press the push-button under fav (favorites). 3. Select the number of favorites pages by pressing the push-button unde...

  • Page 169

    169 . . . – section 1 information button press info to view additional text information related to the current rds fm station or mp3 song. Continue pressing the button to highlight the desired category or press a push-button under a desired category to obtain additional information. Additional text ...

  • Page 170

    Instrumentation and controls . . . 170 source selection press cd/aux to switch between the available audio sources: • cd/dvd audio player • auxiliary device (if connected) • usb storage device (if con- nected) if a disc is not loaded and you press the cd/aux button, the message no disc inserted will...

  • Page 171

    171 . . . – section 1 press and hold fwd to go to the end of the buffer and resume playing the live radio broadcast. The time shift buffer status bar will no longer be displayed. When the radio station is changed, the time shift buffer is cleared. The audio system will restart the buffer and add the...

  • Page 172

    Instrumentation and controls . . . 172 rds features are only available for use on fm stations which broadcast rds information. In rare cases, a station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, please contact the radio station. When y...

  • Page 173

    173 . . . – section 1 emergency alerts the system will automatically interrupt the audio to bring you local or national emergency broadcasts. Alert or alarm appears on the display. The announcement is heard even if the volume is set low or a compact disc is playing. When the emergency broadcast is o...

  • Page 174

    Instrumentation and controls . . . 174 ta will appear on the display while the traffic announcement plays. The announcement is heard even if another audio source is playing. When the traffic announcement is over, the radio will return to your previous listening mode. To stop listening to an announce...

  • Page 175

    175 . . . – section 1 3. You may choose one of the following two modes: - af on (alternate frequency on) select this option to enable this feature. - af off (alternate frequency off) select this option to disable this feature. You may set the system to perform narrow searches including only frequenc...

  • Page 176

    Instrumentation and controls . . . 176 cd/dvd audio player this player is not a cd changer. You may load only one disc at a time into this player. Insert a disc part-way into the slot, label side up. The player will pull it in the rest of the way. If the sound system is on, the disc will begin to pl...

  • Page 177

    177 . . . – section 1 ejecting discs press and release to eject the disc that is currently playing. You will hear a beep. Ejecting disc will appear on the display. Once the disc is ejected, remove disc will appear on the display. If the disc is not removed within a short period of time, it will auto...

  • Page 178

    Instrumentation and controls . . . 178 seeking push the seek right arrow button to move quickly to the beginning of the next track. To restart the current selection if it has been playing for more than five seconds, push the seek left arrow button. If you hold the button down, or if you press it mor...

  • Page 179

    179 . . . – section 1 music groupings to change the music grouping, press the push-button under menu to display a list of all music groupings on the disc. Rotate the menu/select knob to scroll through the list. Press the knob to select the desired item. The first track of the selected music grouping...

  • Page 180

    Instrumentation and controls . . . 180 fast forward/reverse press the fwd or rev button to move quickly ahead or back to another part of the current track. • press the button once to move through the current track at twice the normal playing speed. • press the button twice to move through the curren...

  • Page 181

    181 . . . – section 1 dvd prestop (dvd pre-stop) will appear on the display. To resume playing the disc, press the / (play/pause) button while dvd prestop appears on the display. The dvd will resume play from the point where the disc was stopped. Press the push-button under (stop) again to stop play...

  • Page 182

    Instrumentation and controls . . . 182 hard disc drive your sound system is equipped with a 40 gb hard disc drive that allows you to record tracks from audio cds, mp3/wma discs and usb mass storage devices. A portion of the hard disc drive is used for the storage of radio system files. The remainder...

  • Page 183

    183 . . . – section 1 to stop the recording process prior to completion, first press rec to display the "stop recording" option above a push-button, then press the "stop recording" push- button. If you eject the disc or turn off the ignition before the recording process is complete, only tracks that...

  • Page 184

    Instrumentation and controls . . . 184 to facilitate hard disc drive naviga- tion, discs with items identified as no info can first be converted to mp3 format with tag information on a home computer and can then be recorded to the hard disc drive from an mp3 disc or usb device. See the following, la...

  • Page 185

    185 . . . – section 1 the following file types are not fully supported and may not play or may be shown without tag information: • aac (advanced audio coding) • ogg vorbis without tag information, these file types may be identified only by filename. Usb host support you may connect a usb flash drive...

  • Page 186

    Instrumentation and controls . . . 186 hard disc drive playback modes while the hard disc drive plays, one of the following playback modes will be displayed: • shuffle while this mode is displayed, the system is playing all stored hard disc drive content in random order. • artist while this mode is ...

  • Page 187

    187 . . . – section 1 hard disc drive menu to change the hard disc drive playback mode, do the following: 1. Press the menu/select knob to display the hard disc drive menu. 2. Rotate the menu/select knob to highlight the desired menu item. You may choose one of the following modes: - shuffle songs -...

  • Page 188

    Instrumentation and controls . . . 188 the settings are described below. • shuffle songs select this mode to hear the content of the hard disc drive in random, rather than sequential, order. • playlist select this mode to display the six favorite playlists. Select one of the playlists, then select a...

  • Page 189

    189 . . . – section 1 • song titles the number of files in this mode will appear next to the name of the playback mode. Select this menu item to dis- play a list of songs. Select a song to begin play- back. After the song has finished playing, all songs stored on the hard disc drive will continue pl...

  • Page 190

    Instrumentation and controls . . . 190 • audiblebook (audi- ble.Com ® audio book) select this menu item to play audio book content down- loaded from www.Audi- ble.Com ® . Audio books from www.Audi- ble.Com ® can be burned to a cd or copied to a usb storage device, and then can be recorded to the har...

  • Page 191

    191 . . . – section 1 configuring hard disc drive favorites 1. Press the config (configure) button to display the radio setup menu. 2. Press the push-button under hdd (hard disc drive) to dis- play the available favorites modes. 3. Press the push-button under the "favorites" label to set the availab...

  • Page 192

    Instrumentation and controls . . . 192 cd and music-related data from gracenote, inc., copyright © 2000-2007 gracenote. Gracenote software, copyright © 2000-2007 gracenote. This product and service may practice one or more of the following u.S. Patents: #5,987,525; #6,061,680; #6,154,773, #6,161,132...

  • Page 193

    193 . . . – section 1 you agree not to use or exploit gracenote data, the gracenote software, or gracenote servers, except as expressly permitted herein. You agree that your non-exclusive license to use the gracenote data, the gracenote software, and gracenote servers will terminate if you violate t...

  • Page 194

    Instrumentation and controls . . . 194 gracenote is not obligated to provide you with new enhanced or additional data types or categories that gracenote may provide in the future and is free to discontinue its services at any time. Gracenote disclaims all warranties express or implied, including, bu...

  • Page 195

    195 . . . – section 1 • make sure the mp3/wma files are recorded on a cd-r, cd- rw or dvd+/-r disc or a usb storage device. • do not mix standard audio and mp3/wma files on one disc. • when burning an mp3 disc using multiple sessions, make sure to finalize the disc. It is usually better to burn the ...

  • Page 196

    Instrumentation and controls . . . 196 root directory the root directory will be treated as a folder. • if the root directory of the mp3/wma disc contains compressed audio files, the directory will be displayed as f1 mp3. • if the root directory of a usb storage device contains compressed audio file...

  • Page 197

    197 . . . – section 1 file system and naming the displayed song title is taken from the file's id3 tag. If a song title is not present in the id3 tag, the radio will display the file name as the track name. Track names longer than 32 char- acters will be shortened. Playlists the player will not reco...

  • Page 198

    Instrumentation and controls . . . 198 previous/next folder to move ahead to the first track in the next folder, press the push- button under . To play the first track in the previous folder, press the push- button under . Fast forwarding/rewinding press and hold the fwd or rev button to move quickl...

  • Page 199

    199 . . . – section 1 care of your cds and dvds handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water and clean...

  • Page 200

    Instrumentation and controls . . . 200 portable audio device a portable audio player such as an mp3 player, ipod, pda, laptop computer (with microphone output), or a cassette player can be connected to the sound system to play over the radio and speakers. • if your vehicle is equipped with a cd chan...

  • Page 201

    201 . . . – section 1 volume control rotate the vol (volume/power) knob to the right to increase the volume and to the left to decrease the volume. You may need to make additional volume adjustments to the portable audio device to achieve the desired volume. Source selection if your vehicle is equip...

  • Page 202

    Instrumentation and controls . . . 202 connecting an ipod using the usb port if your vehicle is equipped with a cd changer, see "connecting a portable audio device using the auxiliary input jack" earlier in this section for information about connecting an ipod to the sound system. Your vehicle is eq...

  • Page 203

    203 . . . – section 1 ipod menu press the menu/select knob to display the ipod menu on the hard disc drive. Rotate the menu/select knob to highlight the desired menu item. Press the menu/select knob to select the desired option. Source selection there are three ways to select your desired audio sour...

  • Page 204

    Instrumentation and controls . . . 204 steering wheel audio controls your vehicle is equipped with steering wheel-mounted audio controls. Source selection (if equipped)) note: this feature is not available on cts-v models. Press to switch between the available audio sources: • am band (if equipped) ...

  • Page 205

    205 . . . – section 1 seeking press the top or bottom of switch to move quickly to the next or previous preset radio station on the current band. The radio will not stop on stations with weak reception. When a compact disc is playing, press the up or down arrow to select the next or previous track o...

  • Page 206

    Instrumentation and controls . . . 206 anti-theft feature theftlock is designed to discourage radio theft by learning a portion of the vehicle identification number. The theft deterrent feature is automatically enabled and therefore no programming is necessary. When the ignition is turned off, the s...

  • Page 207

    207 . . . – section 1 ■ navigation system (if equipped) the navigation system is located at the center of the instrument panel. The system consists of control buttons and a screen and is equipped with a navigation guidance system with route planning. It may also come with the follow- ing tools or in...

  • Page 208

    Instrumentation and controls . . . 208 ■ controls mounted on steering wheel/ column you will find the following controls mounted on the steering wheel or steering column. Multifunction lever use this lever to control the following features: • turn signal • exterior lights • fog lights see "multifunc...

  • Page 209

    209 . . . – section 1 horn sound the horn by pressing the horn symbols on your steering wheel. Ignition switch see "starting and operating instructions" for more information on the ignition switch . Telescopic and tilt steering wheel control you can change the angle and depth of the steering wheel t...

  • Page 210

    Instrumentation and controls . . . 210 telescopic power tilt wheel control (if equipped) move the switch in the direction you want the wheel to move. Press the switch up or down to tilt the wheel up or down. Press the switch toward the front of the vehicle to move the steering wheel farther into the...

  • Page 211

    211 . . . – section 1 • audio system your vehicle is equipped with steering wheel-mounted radio controls. See "audio system" earlier in this section for more information. • navigation system voice rec- ognition button (if equipped) with the navigation system, this button controls the voice recogniti...

  • Page 212

    Instrumentation and controls . . . 212 ■ multifunction lever turn signal to signal a turn, move the lever all the way up or down. When the turn is over, the lever will return automatically. To signal a lane change, just raise or lower the lever until the arrow starts to flash. Hold it briefly until ...

  • Page 213

    213 . . . – section 1 high-low beam control pull the multifunction lever toward you to select low-beams or push it away from you to select the high-beam headlights. When the high beams are on, an indicator light on the instrument cluster will also be on. You can also flash your high beams to signal ...

  • Page 214

    Instrumentation and controls . . . 214 notice clear any ice or snow from the wiper blades before using them to prevent damage to the blades and overloading the wiper motor. The wipers are protected by a circuit breaker. If there is an electri- cal overload, the wiper system will stop until the motor...

  • Page 215

    215 . . . – section 1 if the system is left on for a long period of time, occasional wipes may occur without any moisture on the windshield. This is normal. It indicates that the system is activated. To override this feature and oper- ate the wipers manually, move the stalk up to the low or high spe...

  • Page 216

    Instrumentation and controls . . . 216 windshield washer to spray washer fluid on the windshield, push in the button at the end of the stalk. The washer will spray until you release the button. The wipers will clear the window and then either stop or return to your preset speed. If the washer fluid ...

  • Page 217

    217 . . . – section 1 heated washer fluid (if equipped) push the heated washer fluid button, located on the heating and air conditioning system control panel, to activate the heated washer fluid system. The following message will appear in the driver information center display: • heated washer fluid...

  • Page 218

    Instrumentation and controls . . . 218 headlight washers to wash your headlights, activate the windshield washer while the headlights are on. The windshield and headlights will be washed. The headlight washers will cycle once every fifth time the windshield washer is activated. The headlights must b...

  • Page 219

    219 . . . – section 1 to set your cruise control 1. Press the cruise control on/off button. The indicator light on the button will glow when the system is on. 2. Accelerate to the speed you want. 3. Press the set button and release it. 4. Take your foot off the accelerator pedal. When the cruise con...

  • Page 220

    Instrumentation and controls . . . 220 to get out of cruise control to temporarily turn off cruise control without erasing the set speed memory, do one of the following: • step on the brake pedal or push the clutch pedal if you have a manual transmission. • press the cruise control cancel button . T...

  • Page 221

    221 . . . – section 1 when you press the res (resume/ accelerate) button to return to your chosen speed, don't hold the button down. If you hold it, the vehicle will accelerate and continue to gain speed. It will keep going faster until you release the button or apply the brake. The cruise control s...

  • Page 222

    Instrumentation and controls . . . 222 to go to a slower speed • press and hold the set button. Your vehicle will slow down. When it gets to the lower speed you want, let go of the button. The vehicle will maintain the lower speed. • tapping the button will lower your vehicle’s speed by 1.6 km/h (1 ...

  • Page 223

    223 . . . – section 1 ■ mirrors outside mirrors adjust the outside mirrors so that you just see the side of your vehicle when you are sitting in a comfort- able driving position. The passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. Ca...

  • Page 224

    Instrumentation and controls . . . 224 when you are finished, press button or again to deselect the mirror. For information on programming two sets of outside mirror positions into memory, see "memory feature" later in this section for more information. Heated mirror the outside mirrors are heated e...

  • Page 225

    225 . . . – section 1 a disengaged mirror may shake or flutter at normal driving speeds and may not stay in position. If a mirror ever becomes disengaged, it will need to be reset. To reset a mirror, fold and unfold it using the power controls. Curb view assist mirror (if equipped) if your vehicle i...

  • Page 226

    Instrumentation and controls . . . 226 automatic inside day/night mirror your vehicle may be equipped with the fully automatic inside rearview mirror which has an on/ off button at the base of the mirror. During the day the mirror reflects all the light from behind your vehi- cle. At night, when the...

  • Page 227

    227 . . . – section 1 caution do not leave children in the vehicle with the ignition key or a transmitter. If your vehicle is equipped with the keyless access system, vehicle ignition and starting functions could be activated if the transmitter is in the vehicle. The children could operate the power...

  • Page 228

    Instrumentation and controls . . . 228 to activate the express open mode and open the window all the way, press the front of the switch all the way down to the second position and release. To stop the window while it is lowering, pull the switch up briefly. To raise the window, pull the front of the...

  • Page 229

    229 . . . – section 1 anti-pinch feature if a head, hand or another object is in the way of the window as it is express-closing, the window will stop and open to a preset position. The window will function normally once the obstruction is removed. The anti-pinch feature may also be activated by cert...

  • Page 230

    Instrumentation and controls . . . 230 you can control the passenger windows with the switches on the driver’s door armrest while this feature is activated. Press the button again to turn the passengers' window controls back on. The indicator light in the button will glow when the lock-out feature i...

  • Page 231

    231 . . . – section 1 manual door locks from the inside, use the manual door lock to lock and unlock each door individually. From the outside, use your key to lock or unlock the doors. Your vehicle is equipped with a deadbolt door locking system. See "deadbolt" later in this section for more informa...

  • Page 232

    Instrumentation and controls . . . 232 your vehicle is equipped with a deadbolt door locking system. See "deadbolt" later in this section for more information. If the theft deterrent system is armed, remember to unlock the doors with a transmitter to avoid setting off the alarm. See "theft deterrent...

  • Page 233

    233 . . . – section 1 central door lock system locking the driver’s door will lock all the doors. Deadbolt your vehicle is equipped with a deadbolt locking feature in addition to the standard door locks. If your vehicle is equipped with the keyless access system, the deadbolt is engaged whenever you...

  • Page 234

    Instrumentation and controls . . . 234 if your vehicle is equipped with the remote keyless entry system, unlocking the driver's door from the outside with the removable ignition key disengages the dead- bolt for all doors. However, only the driver’s door will be unlocked. You must unlock the passeng...

  • Page 235

    235 . . . – section 1 anti-lockout feature if your vehicle is equipped with a removable ignition key, when the power door lock switch is pressed while a door is open and the key is in the ignition, all the doors will lock and the driver's door will unlock. To override this feature and lock the doors...

  • Page 236

    Instrumentation and controls . . . 236 when the security lock is engaged, you can lock and unlock the rear doors using the transmitter, the front power door lock switch or by lifting the rear door lock manually. But the door can only be opened from the outside. Security lock activation to activate t...

  • Page 237

    237 . . . – section 1 if the vehicle is locked, the trunk will open only if a recognized keyless access transmitter is within 1 meter (3 ft) of the trunk opening. If your vehicle has an automatic transmission, your shift lever must be in p (park) or n (neutral) for the release to work. If you have a...

  • Page 238

    Instrumentation and controls . . . 238 emergency trunk release handle notice the emergency trunk release handle should not be used to tie down the trunk lid or as an anchor point when securing items in the trunk. Improper use of the trunk release handle could damage it. The purpose of this release h...

  • Page 239

    239 . . . – section 1 tire sealant and compressor kit (if equipped) if your vehicle is equipped with a tire sealant and compressor kit, your vehicle has neither a spare tire, nor jacking equipment. See "tire sealant and compressor kit" in section 5 for more information. Jack and spare tire removal (...

  • Page 240

    Instrumentation and controls . . . 240 sunroof the right switch operates the sunroof. Press and hold the front of the switch to open the sunroof to the vent position. The sunshade will also open a few centimeters (inches). To close the vent, press and hold the back of the switch. From the vent posit...

  • Page 241

    241 . . . – section 1 to stop the sunshade while it is opening or closing, press the front or rear of the switch again. Anti-pinch feature if a head, hand or another object is in the way of the sunroof or sunshade as it is closing, the sunroof or sunshade will stop and open. Once the obstruction is ...

  • Page 242

    Instrumentation and controls . . . 242 cupholders there are two cupholders at the front of the center console. To open the cupholder, push on the cover. There are also cupholders located in the rear seat center armrest. To access the cupholders, fold the armrest down. Convenience net see "trunk area...

  • Page 243

    243 . . . – section 1 ■ retained accessory power your vehicle has retained accesso- ry power, which allows you to operate the following electrical accessories for up to 10 minutes after you turn the ignition off, unless a door is opened: • audio system • power windows • sunroof (if equipped) if you ...

  • Page 244

    Instrumentation and controls . . . 244 ■ electric power management this system monitors the tempera- ture and charge status of the vehi- cle’s battery and automatically adjusts the voltage to enhance performance and extend battery life. You may see the battery voltage reading fluctuate in the driver...

  • Page 245

    245 . . . – section 1 ■ object detection ultrasonic rear parking assist this feature is designed to make rear and parallel parking easier by assisting you in determining how close the rear of your vehicle is to an object. Caution use care when parking your vehicle. Always check for people, other veh...

  • Page 246

    Instrumentation and controls . . . 246 the system's display, located inside the vehicle above the rear window, can be seen by looking over your shoulder. When the vehicle speed is less than 8 km/h (5 mph) and you shift into reverse gear, the system will turn on automatically. Three lights on the dis...

  • Page 247

    247 . . . – section 1 • an object is hanging out of the trunk. • a tow bar is attached to the vehicle. • the system receives vibrations from a large nearby vehicle or from heavy equipment such as a jackhammer. If the system is still disabled after conditions return to normal and driving forward at a...

  • Page 248

    Instrumentation and controls . . . 248 caution after the hood has lifted, the rear hood hinge area may be hot. Do not touch the pedestrian protection system components. The pedestrian protection system is designed to lift the hood only once. Have the vehicle towed for service. If the frontal impact ...

  • Page 249

    249 . . . – section 1 the service pedestrian protection system message will appear when there is a prob- lem with the pedestrian protection system. See your dealer for service immediately. For more information, see "driver information center" earlier in this section. During a frontal impact involvin...

  • Page 250

    Instrumentation and controls . . . 250 removing the actuators notice do not open the hood from the front of the vehicle. The hood or other parts of the vehicle could be damaged. After the pedestrian protection system raises the hood, a gap is created between the rear of the hood and the fender. One ...

  • Page 251

    251 . . . – section 1 5. With your other hand, rotate the actuator toward the center of the engine compartment until the windshield side of the actuator faces the center of the vehicle. 6. Push the actuator towards the center of the vehicle until the lower portion of the actuator is no longer locked...

  • Page 252

    Instrumentation and controls . . . 252 13. Make sure there are no obstructions on either side of the vehicle that could prevent the hood from being securely latched. Note: always latch the right side of the hood first. Caution you or others could be injured when the hood is lowered or latched. Be su...

  • Page 253

    253 . . . – section 1 if you do not have the system repaired, the pedestrian protection system will not be operable in the event of another crash or frontal impact involving a pedestrian. See your dealer for service immediately. Caution safety procedures must always be observed when disposing of the...

  • Page 254

    Instrumentation and controls . . . 254 now, when your transmission is in p (park) for an automatic transmission, or the parking brake is set for a manual transmission, and you press one of the memory buttons, 1 or 2, you will hear a chime and the seat, power tilt and telescopic steering column (if e...

  • Page 255

    255 . . . – section 1 exiting the vehicle to make it easy to get in and out of the vehicle, you can use the exit button. The automatic transmission must be in p (park) or with a manual transmission, the parking brake must be engaged. Pressing this button recalls the memory exit position. A chime wil...

  • Page 256

    Akeng40_cts page 256 wednesday, july 23, 2008 11:47 am.

  • Page 257

    257 . . . Section 2 - seats and restraints seat controls .................................................258 manual seat controls ...................................258 power seat controls .....................................260 heated front seats .......................................263 heated ...

  • Page 258

    Seats and restraints . . . 258 ■ seat controls manual seat controls (if equipped) lift the bar under the front seat to slide the seat backward and forward. Release the bar and make sure the seat is locked into place. Caution a seat that is not locked into place properly could move during a sudden st...

  • Page 259

    259 . . . – – section 2 caution a seat that is not locked into place properly could move during a sudden stop or collision. People in the vehicle could be injured. Make sure the seat is locked in place. Manual seat extension control (if equipped) if your vehicle is a cts-v model, it may be equipped ...

  • Page 260

    Seats and restraints . . . 260 power seat controls (if equipped) the power seat controls are located on the outboard sides of the front seats. The horizontal switch adjusts the seat. The front part of the switch makes the front of the seat go up and down. The rear part of the switch makes the rear o...

  • Page 261

    261 . . . – – section 2 caution sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can't do their job when the seatback is excessively reclined. Improperly positioned safety belts may cause neck injury or injury to the vulnerable ...

  • Page 262

    Seats and restraints . . . 262 press and hold the front or rear of the control to increase or decrease lumbar support for the entire seatback. Power bolsters control press the top or bottom of control to increase or decrease support in the seat cushion bolsters. Press the top or bottom of control to...

  • Page 263

    263 . . . – – section 2 heated front seats (if equipped) your vehicle may be equipped with the optional heated seats. Use this feature to warm the seatback and seat cushion. The ignition has to be on for this feature to work. Press to turn the heated seat feature on and off, and to switch between th...

  • Page 264

    Seats and restraints . . . 264 heated and ventilated front seats (if equipped) use this feature to heat the seatback and seat cushion, or to ventilate the seat. The ignition has to be on for this feature to work. The button closest to the driver is for the driver’s seating position. The button close...

  • Page 265

    265 . . . – – section 2 head restraints the front head restraints are adjustable. To adjust a front head restraint to the proper height, slide the head restraint up. The top of the restraint should be closest to the top of your head. The front head restraints automatically tilt forward to provide ad...

  • Page 266

    Seats and restraints . . . 266 split folding rear seatback your vehicle has a split rear seat which can be folded down for additional cargo space. This feature allows you to access the trunk compartment from the rear seats. Either side of the rear seatback can be folded down for additional storage s...

  • Page 267

    267 . . . – – section 2 ■ safety belts caution do not let anyone ride where they cannot wear a safety belt properly. If you are in a crash and you are not wearing a safety belt, you can be seriously injured or killed. In a crash, a vehicle occupant who is not restrained properly could become airborn...

  • Page 268

    Seats and restraints . . . 268 caution do not allow anyone to ride in any area of the vehicle that is not equipped with seats and safety belts. Notice before you close the door, make sure the safety belt is out of the way. Otherwise, the belt and/or the vehicle body could be damaged. The safety belt...

  • Page 269

    269 . . . – – section 2 lap/shoulder belt the lap/shoulder belt should be worn properly, as described below. To fasten the belt: 1. Adjust the seat and sit up straight. 2. Pick up the latch plate. 3. Pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull it out v...

  • Page 270

    Seats and restraints . . . 270 6. Pull on the shoulder section to adjust the lap fit. For smaller occupants, you may need to pull the stitching on the lap belt through the latch plate to fully tighten the belt. The safety belt locks if there is a sudden stop or crash, or if you pull the belt very qu...

  • Page 271

    271 . . . – – section 2 when using a seat belt, sit up straight and keep your feet on the floor in front of you. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt should not cross the face or n...

  • Page 272

    Seats and restraints . . . 272 shoulder belt comfort guides your vehicle is equipped with rear shoulder belt guides which provide comfort and support for some adults and children. These guides work by pulling the shoulder belt away from the neck and head. There is one guide for each of the rear outs...

  • Page 273

    273 . . . – – section 2 3. Be sure the belt is not twisted and that the elastic cord is under the belt and the guide is on top. Caution make sure the shoulder portion of the belt is midway over the shoulder and across the chest. Wearing a safety belt improperly could cause serious injury. To remove ...

  • Page 274

    Seats and restraints . . . 274 replacing safety belts caution a crash can damage the restraint systems so that they do not provide proper protection. This could result in serious injury or even death in a collision. To help make sure your restraint systems are working properly after a crash, have th...

  • Page 275

    275 . . . – – section 2 safety belt use during pregnancy safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap/shoulder belt, and the lap portion should be worn a...

  • Page 276

    Seats and restraints . . . 276 the chime and light will repeat if the driver remains unbuckled and the vehicle is in motion. If the driver's belt is already buckled, neither the chime nor the light will come on. Passenger safety belt reminder light the passenger safety belt reminder light is located...

  • Page 277

    277 . . . – – section 2 ■ supplemental restraints caution a crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. Have the restraint systems inspected after a collision. M...

  • Page 278

    Seats and restraints . . . 278 caution safety procedures must always be observed when disposing of the vehicle or vehicle parts. Disposal should only be performed by an authorized service center, to help protect the environment and your health. Air bag system your vehicle is equipped with two air ba...

  • Page 279

    279 . . . – – section 2 your vehicle is also equipped with two seat-mounted side-impact air bags and two roof-mounted air bags. During a side collision, the seat- mounted air bag, on the same side of the vehicle as the impact, may inflate from the outboard side of the front seatback. Both roof-mount...

  • Page 280

    Seats and restraints . . . 280 caution both the safety belt restraint system and the air bag restraint system are designed to best protect adults. Anyone who is up against, or very close to, an inflating air bag could be seriously injured or killed. Everyone in your vehicle who has outgrown child re...

  • Page 281

    281 . . . – – section 2 caution although your vehicle is equipped with a passenger air bag deactivation feature which is designed to turn off the passenger's air bag under certain conditions, no system is fail-safe. No one can guarantee that an air bag will not deploy under some unusual circum- stan...

  • Page 282

    Seats and restraints . . . 282 caution do not attach anything to the area from where the air bag inflates. If something is between an occupant and an air bag, the air bag might not inflate properly or it might force the object into the occupant, causing severe injury or even death. The path of an in...

  • Page 283

    283 . . . – – section 2 the air bag only inflates once. It must be replaced after a collision. Let only qualified technicians work on the air bag system. Caution after an air bag inflates, the air bag components may be hot. Do not touch the air bag components. In many severe crashes, wind- shields a...

  • Page 284

    Seats and restraints . . . 284 air bag light the air bag light on your instrument cluster flashes when you turn on the ignition to indicate that the restraint is in good working order. See "air bag light" in section 1 for more information. Caution have your vehicle serviced right away if the air bag...

  • Page 285

    285 . . . – – section 2 the passenger sensing system will turn off the passenger frontal air bag under the following conditions: • the front passenger seat has no weight placed on it for a period of time. • the system detects a child in a rear-facing infant seat. • the system detects a child in a fo...

  • Page 286

    Seats and restraints . . . 286 the "off" indicator will stay on if the front passenger's air bags are deactivated. When the system senses that a person of adult size is sitting in the front passenger seat, the front passenger's air bags will be reacti- vated and the "on" indicator will appear in the...

  • Page 287

    287 . . . – – section 2 caution if the air bag light stays on or comes on while you are driving, there may be a problem with this system. See "air bag light" in section 1 for more information. If the front passenger seat is wet, the passenger sensing system may not work properly. If the front passen...

  • Page 288

    Seats and restraints . . . 288 system operation with a child restraint accident statistics show that children are safer if they are restrained in a child restraint system secured in the rear seat. It is therefore recommended that children in child restraints and older children who are large enough t...

  • Page 289

    289 . . . – – section 2 caution (continued) it is therefore recommended that children in child restraints and older children who are large enough to wear a safety belt be secured in a rear seat position. In fact, because the risk to a rear-facing child is so great if the air bag deploys, there is a ...

  • Page 290

    Seats and restraints . . . 290 caution if the "on" indicator still appears, secure the restraint in a rear seat position and have your vehicle serviced as soon as possible. See "child restraints" later in this section. System operation with adult passengers when the system senses that a person of ad...

  • Page 291

    291 . . . – – section 2 a thick layer of material (such as a blanket) or aftermarket equipment (such as seat covers, heaters or massagers) can affect how the passenger sensing system oper- ates. Remove any additional mate- rial from the seat. Move the seatback to the upright position. Make sure the ...

  • Page 292

    Seats and restraints . . . 292 passenger air bag on/off indicator when you start the vehicle, the system will perform a self-check. The air bag "on" and "off" indicators will appear briefly in the passenger air bag on/off indicator (located on the instrument panel). If your vehicle is equipped with ...

  • Page 293

    293 . . . – – section 2 child restraints caution do not leave children unattended in the vehicle. Children left unattended could play with the safety belts. The belt could become wrapped around the child’s neck and continue to tighten. The child could be injured or killed. Never allow children to pl...

  • Page 294

    Seats and restraints . . . 294 for most types of child restraints, there are several different models available. When choosing a child restraint, take into consideration not only the child’s weight, size and age, but also whether the restraint will be compatible with your vehicle. The restraint manu...

  • Page 295

    295 . . . – – section 2 caution a young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdo- men. In a crash, the belt would apply force on a body area that is unprotected by ...

  • Page 296

    Seats and restraints . . . 296 before installing a child restraint in the front passenger position, remove any additional material from the seat such as blankets, cushions, seat covers, seat heaters or seat massagers. See "passenger sensing system" earlier in this section for more information. When ...

  • Page 297

    297 . . . – – section 2 child restraints with top straps can only be used in rear seating positions. There are no anchor brackets available for front seating positions. See "top strap" later in this section. Accident statistics show that children are safer if they are restrained in a child restraint...

  • Page 298

    Seats and restraints . . . 298 caution although your vehicle is equipped with a passenger air bag deactivation feature which is designed to turn off the passenger's air bag under certain conditions, no system is fail-safe. No one can guarantee that an air bag will not deploy under some unusual circu...

  • Page 299

    299 . . . – – section 2 caution when the vehicle is started with a child restraint installed in the front passenger seat, the "off" indicator should appear in the passenger sensing system status bar after the system has completed its self-check. If the "on" indicator appears when you have installed ...

  • Page 300

    Seats and restraints . . . 300 use the following chart to determine which seats in the vehicle are suitable for the isofix child restraint systems. Mass group size class fixture vehicle isofix positions front passenger right rear outboard passenger left rear outboard passenger rear center passenger ...

  • Page 301

    301 . . . – – section 2 †: suitable for isofix "universal" category forward-facing restraints approved for use in this mass group. X: seat position not suitable for isofix restraints in this mass group and/or size class. Child restraint system size classes and fixtures are as follows: a - iso/f3: fu...

  • Page 302

    Seats and restraints . . . 302 older children older children who have outgrown booster seats should sit in a rear seat, restrained by a properly fastened safety belt. The child restraint manufacturer's instructions should state the weight and height limitations for the particular restraint. To deter...

  • Page 303

    303 . . . – – section 2 • can the proper safety belt fit be maintained for the duration of the trip? If you answered "no" to this question, the child should continue to use a booster seat. If you answered "yes" to this question, an older child should wear a lap/shoulder belt and get the additional r...

  • Page 304

    Seats and restraints . . . 304 anchors for child restraints with lower attaching points and top strap this system is designed to make installation of child restraints easier. With this feature you will have anchors where the seatback meets the seat cushion in the outboard rear seats. To use the syst...

  • Page 305

    305 . . . – – section 2 top strap a child restraint may have a top strap. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored. Others require that the top strap be anchored. Read and follow all instructions that come with the restraint. A child ...

  • Page 306

    Seats and restraints . . . 306 child restraints that require the top strap to be anchored can only be used in rear seating positions. There are no anchor brackets avail- able for front seating positions. Caution each bracket is designed to anchor only one child restraint. Attaching more than one chi...

  • Page 307

    307 . . . – – section 2 for a forward-facing child restraint, attach the top strap to the top strap anchor. • if the child restraint has a single top strap, route the top strap over the head restraint. • if the child restraint has a dual top strap, route the top straps around the head restraint. Con...

  • Page 308

    Seats and restraints . . . 308 notice contact between the child restraint’s lower attachment parts and the vehicle’s safety belt assembly may result in damage. If necessary, move the fastened safety belt so that the belt assembly and the lower attachment parts do not rub together. When securing unus...

  • Page 309

    309 . . . – – section 2 be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. 2. Place the child restraint on the seat. 3. Attach the child restraint’s attachment points to the anchors in the vehicle, and tighten as n...

  • Page 310

    Akeng40_cts page 310 wednesday, july 23, 2008 11:47 am.

  • Page 311

    311 . . . Section 3 - starting and operating instructions new vehicle break-in period.........................313 keys................................................................313 immobilizer...................................................315 theft deterrent system.............................

  • Page 312

    . . . 312 section 3 - starting and operating instructions vehicle parking ..............................................356 manual transmission ...................................356 automatic transmission ...............................357 traction......................................................

  • Page 313

    313 . . . – – – section 3 ■ new vehicle break-in period notice your vehicle doesn't need an elaborate "break-in". But it will perform better in the long run if you follow these guidelines: • don't drive at a constant speed - fast or slow - for the first 800 km (500 miles). Don't make full-throttle s...

  • Page 314

    Starting and operating instructions . . . 314 your vehicle’s ignition is operated using either a standard, removable key or using an integrated, non- removable key called the ignition control knob. • removable ignition key this key is used for the driver's door, ignition and glove box. If you can re...

  • Page 315

    315 . . . – – – section 3 to remove the key from the transmitter, press the button near the bottom of the transmitter and pull the key out. Always press the button before pulling the key out of the transmitter. See "keyless access system" later in this section for more information. Note that there i...

  • Page 316

    Starting and operating instructions . . . 316 ■ theft deterrent system notice do not alter the vehicle immobilizer/theft deterrent system or the vehicle alarm system. Such tampering could affect the performance of the system. Your vehicle is equipped with a theft deterrent system. In addition to sta...

  • Page 317

    317 . . . – – – section 3 - if your vehicle is equipped with the keyless access system, the vehicle's passive locking feature can automatically lock the vehicle and arm the theft deterrent system when you exit the vehicle. See "keyless locking" under "driver information center" in section 1. 3. Clos...

  • Page 318

    Starting and operating instructions . . . 318 the power door lock switch will not work to unlock the vehicle when the alarm is set. The power sounder has an internal battery. If the vehicle loses battery power when the theft deterrent system is armed, the power sounder will activate automatically. T...

  • Page 319

    319 . . . – – – section 3 before arming the theft deterrent system and activating the intrusion sensor, do the following: • make sure all doors, windows and the sunroof (if equipped) are completely closed. • turn off any fans or blowers. Moving air may trigger the alarm. • be sure to secure any loos...

  • Page 320

    Starting and operating instructions . . . 320 cleaning the system sensor to clean the sensor, spray the cleaner on a soft, clean cloth and wipe gently. Make sure the cleaner does not leave any residue. Notice do not spray cleaner directly onto the intrusion sensors. Do not use brushes. The bristles ...

  • Page 321

    321 . . . – – – section 3 immobilizer (remote keyless entry system) if your vehicle has a removable ignition key, the ignition key has a transponder imbedded in it. The transponder uses a radio frequency that matches a decoder in your vehicle. The system is armed when the key is removed from the ign...

  • Page 322

    Starting and operating instructions . . . 322 4. Within five seconds of turning off the ignition, insert the other previously programmed key and start the engine. If the engine does not start, see your dealer for service. 5. Turn off the ignition and remove the key. 6. Within five seconds of turning...

  • Page 323

    323 . . . – – – section 3 if a damaged or incorrectly matched transmitter has been used, the system will not allow the engine to start. If the engine does not start and the security system light comes on, there may be a problem with the immobilizer system. Turn the ignition off. Place the transmitte...

  • Page 324

    Starting and operating instructions . . . 324 ■ remote keyless entry system (if equipped) if your vehicle is equipped with an ignition control knob, see "keyless access system" later in this section. With this system you can press a transmitter button to lock and unlock your doors and release your t...

  • Page 325

    325 . . . – – – section 3 operation lock press to lock all doors. The fuel door will also lock. See "locking fuel door" in section 4 for more information. Different feedback options may be chosen for the transmitter buttons. For more information, see "feature customization" under "driver information...

  • Page 326

    Starting and operating instructions . . . 326 trunk release press and hold for one second to unlatch the trunk. If your vehicle is equipped with an automatic transmission, the trans- mission must be in p (park) for the release to work. If your vehicle is equipped with a manual transmission, the tran...

  • Page 327

    327 . . . – – – section 3 battery replacement if the system does not respond to the remote transmitter from any location within the normal range, you probably need to replace the battery in the transmitter. Replace battery in remote key may appear in the driver information center display. See "drive...

  • Page 328

    Starting and operating instructions . . . 328 4. Reassemble the transmitter. Snap the top and bottom together. 5. Test the operation of the transmitter with your vehicle. Matching transmitters matching transmitters to your vehicle may be necessary if you lose or replace a transmitter. Even if only o...

  • Page 329

    329 . . . – – – section 3 ■ keyless access system (if equipped) if your vehicle is equipped with a removable ignition key, see "remote keyless entry system" earlier in this section for more information. Caution do not leave children in the vehicle with the keyless access transmitter. Vehicle ignitio...

  • Page 330

    Starting and operating instructions . . . 330 passive functions operate when the transmitter is within 1 meter (3 ft) of the door or trunk. The following passive functions are also available when the transmitter is within range: • the front door will unlock automatically when you pull the door handl...

  • Page 331

    331 . . . – – – section 3 transmitter operation lock press to lock all doors. The fuel door will also lock. See "locking fuel door" in section 4 for more information. Different feedback options may be chosen for the transmitter buttons. For more information, see "feature customization" under "driver...

  • Page 332

    Starting and operating instructions . . . 332 vehicle locator/panic alarm press and release to locate your vehicle. The horn will chirp three times and the turn signal lights will flash three times. When the ignition is off, press and hold for 3 seconds to activate an alarm. To turn the alarm off, p...

  • Page 333

    333 . . . – – – section 3 • check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the right or left. • an electronic device such as a cellular phone or lap-top computer may be causing interference. If none of the above apply, see your dealer or qualified techn...

  • Page 334

    Starting and operating instructions . . . 334 notice when replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. To replace the battery: 1. Insert a thin, flat non-metal object into the slot on the side or ba...

  • Page 335

    335 . . . – – – section 3 4. Reassemble the transmitter. Snap the top and bottom to- gether. 5. Test the operation of the transmitter with your vehicle. Matching transmitters matching transmitters to your vehicle may be necessary if you lose or replace a transmitter. Even if only one transmitter is ...

  • Page 336

    Starting and operating instructions . . . 336 vehicle remote-start (if equipped) this feature is only available on vehicles equipped with an automatic transmission. If enabled, this feature allows you to start the engine from outside the vehicle. To enable or disable this feature, see "feature custo...

  • Page 337

    337 . . . – – – section 3 this feature may automatically activate certain climate control functions when you use the vehicle’s remote starter. If activated, the climate control settings will automatically adjust to where they were last set. Vehicle remote start may activate the following when the ou...

  • Page 338

    Starting and operating instructions . . . 338 to end remote-start engine runtime without transitioning to normal vehicle operation, do any of the following: • aim the transmitter at the vehicle and press the remote-start button until the parking lights turn off. Your transmitter’s range may be less ...

  • Page 339

    339 . . . – – – section 3 for information on other conditions which can affect the performance of the transmitter, see "transmitter range" under "keyless access system" earlier in this section. Transmitter frequency approval code following is the european remote frequency certification code for this...

  • Page 340

    Starting and operating instructions . . . 340 your vehicle’s ignition is operated using either a standard, removable key or using an integrated, non- removable key . The integrated, non-removable key, called the ignition control knob, is installed in vehicles equipped with the keyless access system....

  • Page 341

    341 . . . – – – section 3 notice if your key seems stuck, first make sure that the key is the correct key and that it is in all the way. If your vehicle has a manual transmission, turn the steering wheel to the left and right while you turn the key hard by hand. Do not use a tool to force the key. I...

  • Page 342

    Starting and operating instructions . . . 342 retained accessory power after you turn the ignition off, you can still use the following accessories: • audio system • power windows • sunroof (if equipped) you can operate the radio for up to 10 minutes after the ignition has been turned off or until t...

  • Page 343

    343 . . . – – – section 3 if your vehicle is equipped with an ignition control knob, apply the regular brakes before turning the ignition control knob. Turn the ignition key or ignition control knob to start. Do not push the accelerator pedal. If your vehicle is equipped with an ignition control kno...

  • Page 344

    Starting and operating instructions . . . 344 computer controlled cranking system this feature helps start the engine and protects the components. This feature may cause the engine to crank even after the ignition key or ignition control knob is not in start. If the engine does not start within 15 s...

  • Page 345

    345 . . . – – – section 3 keyless access transmitter not detected if your vehicle is equipped with an ignition control knob, the keyless access transmitter must be in the vehicle for the ignition to work. When the transmitter battery is low, or if the system is not detecting the transmitter because ...

  • Page 346

    Starting and operating instructions . . . 346 failure to start if the engine does not start and no message is displayed in the driver information center, wait 15 seconds before trying again. ■ engine block heater (if equipped) use this option if you have to park in very cold weather, -18°c (0°f) or ...

  • Page 347

    347 . . . – – – section 3 keep the heater plugged in for a minimum of four hours before starting the engine. Be sure to unplug and restow the cord before starting the engine. Otherwise, it may be damaged by moving engine parts. Ask a dealer in the area how long you should keep the heater plugged in....

  • Page 348

    Starting and operating instructions . . . 348 shift positions the shift lever is located on the center console. There are several different shift positions for your gear lever. P (park) this locks your rear wheels. Use this position to park the vehicle and when starting the engine. Your vehicle has ...

  • Page 349

    349 . . . – – – section 3 r (reverse) use this to back up. At low vehicle speeds you can use r (reverse) to rock your vehicle back and forth if your vehicle gets stuck in sand, mud, ice or snow. See "if your vehicle gets stuck" in section 5. Notice shift to r (reverse) only after your vehicle is sto...

  • Page 350

    Starting and operating instructions . . . 350 • going less than about 55 km/h (35 mph), push your accelera- tor pedal about halfway down. • going more than about 55 km/h (35 mph), push the accelerator all the way down. When slippery road conditions exist, downshifting the transmission may cause skid...

  • Page 351

    351 . . . – – – section 3 this feature gives the driver more manual control over the operation of the transmission. Use the driver-controlled shift mode to remain in a gear longer for sport driving or climbing hills, or to downshift for more power or engine braking. The vehicle will have firmer, qui...

  • Page 352

    Starting and operating instructions . . . 352 if your vehicle's transmission shift inhibitor is active, the indicator for the currently selected gear will flash. If your vehicle is a cts model, the transmission will downshift automatically when the vehicle comes to a stop. More power will be availab...

  • Page 353

    353 . . . – – – section 3 the transmission will not automatically shift into the next lower gear if the engine rpm are too high. If shifting is prevented, the display showing the current gear will flash. Manually selecting the second gear position will allow the vehicle to start from a stop in secon...

  • Page 354

    Starting and operating instructions . . . 354 the clutch pedal must be fully pressed in when shifting to ensure the transmission is fully in gear. Your shift lever is in the neutral position when it is centered in the shift pattern. Use the neutral position when you start or idle your engine. If you...

  • Page 355

    355 . . . – – – section 3 one to four skip shift (if equipped) if your vehicle is a cts-v model equipped with a manual transmission, this feature helps improve fuel economy. When the vehicle is under light acceleration, you can only shift from first to fourth gear instead of first to second or first...

  • Page 356

    Starting and operating instructions . . . 356 ■ all-wheel drive (if equipped) the all-wheel drive system automatically monitors and adjusts engine power to the front and rear wheels to provide the best traction and handling. If the electronic stability system senses a loss of traction or stability, ...

  • Page 357

    357 . . . – – – section 3 if your vehicle is equipped with an ignition control knob, remove the keyless access transmitter from the vehicle. You should not park vehicles with trailers on a grade (hill). However, if you must park on a grade, see "parking on hills" under "trailer towing" later in this...

  • Page 358

    Starting and operating instructions . . . 358 caution avoid leaving your vehicle while the engine is running. Be sure the shift lever is in p (park) and the parking brake is applied when you leave your vehicle. If you are not in an idling vehi- cle, the engine could overheat and even catch fire. You...

  • Page 359

    359 . . . – – – section 3 shifting out of p (park) your vehicle has an electronic shift lock release system. With the igni- tion on, you have to fully apply the regular brakes before you can shift out of p (park). The shift lock control system is also designed to prevent the shift lever from moving ...

  • Page 360

    Starting and operating instructions . . . 360 stabilitrak ® system the system helps maintain directional control under slippery road conditions. See section 1 for more information on the stabilitrak ® system. Limited-slip rear axle the locking rear axle can give added traction on snow, ice, etc. Nor...

  • Page 361

    361 . . . – – – section 3 ■ brakes if the engine stops as you're driving, brake normally but don't pump your brakes. If the engine stops, you will have some power brake assist left, but it's used up as you brake. Disc brake wear indicators your vehicle has disc brakes. Disc brake pads have built-in ...

  • Page 362

    Starting and operating instructions . . . 362 brake adjustment every time you apply the brakes, whether or not the vehicle is moving, your brakes adjust for wear. Brake pedal travel see your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. ...

  • Page 363

    363 . . . – – – section 3 parking brake your vehicle is equipped with either a manual or an electric parking brake. • if your vehicle is equipped with a manual parking brake, there is a parking brake pedal located to the left of the driver’s left foot. For more information, see "manual parking brake...

  • Page 364

    Starting and operating instructions . . . 364 notice do not drive with the parking brake set. Driving with the parking brake on could cause the brakes to overheat. The brakes, or other parts of the vehicle, could be damaged. You should not park vehicles with trailers on a grade (hill). However, if y...

  • Page 365

    365 . . . – – – section 3 the system has two warning lights and five driver information center messages. See the following in section 1 for more information: • warning lights - brake system warning light - electric parking brake light • driver information center - driver information center messages ...

  • Page 366

    Starting and operating instructions . . . 366 do not drive the vehicle if the brake system warning light is flashing. See your dealer for service. See the following in section 1 for more information: • warning lights brake system warning light if the electric parking brake is applied while the vehic...

  • Page 367

    367 . . . – – – section 3 if the brake system warning light is flashing, then either the electric parking brake is only partially applied or released, or there is a problem with the electric parking brake. The following message will appear on the driver information center display: • service park bra...

  • Page 368

    Starting and operating instructions . . . 368 releasing the electric parking brake to release the electric parking brake, do the following: 1. Turn the ignition switch to the on position. 2. Hold the regular brake pedal down. 3. Press the electric parking brake switch briefly. If you attempt to rele...

  • Page 369

    369 . . . – – – section 3 notice do not drive with the parking brake set. Driving with the electric parking brake on could overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before ...

  • Page 370

    Starting and operating instructions . . . 370 caution on vehicles with a manual transmission, releasing the clutch and pressing the accelerator will release the electric parking brake. If the manual transmission is not in a gear, the vehicle could move suddenly. You or others may be injured. Make su...

  • Page 371

    371 . . . – – – section 3 magnetic ride control tm (if equipped) note: this feature is only available on cts-v models. This feature allows you to select a suspension mode based on different driving conditions. Press this button, located on the center console, to switch between sport mode and tour mo...

  • Page 372

    Starting and operating instructions . . . 372 ■ speed limiter engine speed limiter when the rpm are too high, the throttle is closed to reduce speed. If the rpm do not decrease, the fuel supply to the engine will be limited in order to avoid damage to the engine. When the rpm return to normal operat...

  • Page 373

    373 . . . – – – section 3 also, see "certification label" for additional loading information. Caution the components of your vehicle are designed to provide satisfactory service if the vehicle is not loaded in excess of the gross vehicle weight rating. Also, do not exceed the front or rear gross axl...

  • Page 374

    Starting and operating instructions . . . 374 certification label this label shows the vehicle's gross vehicle weight rating. The label is typically affixed to your vehicle at one of the following locations: • below the door lock mechanism on the rear frame of the left front door • the rear edge of ...

  • Page 375

    375 . . . – – – section 3 ■ trailer towing (cts-v model only) your vehicle is neither designed nor intended to tow a trailer. ■ trailer towing (cts model only) caution if you don't use the correct equipment and drive properly, you could lose control when you pull a trailer behind your vehicle. You c...

  • Page 376

    Starting and operating instructions . . . 376 the maximum loaded trailer weight you can pull with your vehicle depends on your intended use and what special equipment has been installed on the vehicle. Information on trailer towing ability, special equipment required, and optional equipment availabl...

  • Page 377

    377 . . . – – – section 3 • when towing a trailer with an automatic transmission, operate your vehicle in d (drive). When towing a trailer with a manual transmission, it is best not to use the highest gear. Shift the transmission into a lower gear if the transmission shifts too often under heavy loa...

  • Page 378

    Starting and operating instructions . . . 378 • your vehicle may show signs of overheating if you turn your engine off immediately after towing at high altitudes on steep uphill grades. If possible, park on a level surface. Set the parking brake firmly. Shift the automatic transmission into p (park)...

  • Page 379

    379 . . . – – – section 3 safety chains you should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it becomes separated from the hitch. Instructions about safety chains may be provided...

  • Page 380

    Starting and operating instructions . . . 380 parking on hills caution when towing a trailer, avoid parking your vehicle on a hill. If something were to go wrong, your rig could start to move. People could be injured and both your vehicle and the trailer could be damaged. You should not park vehicle...

  • Page 381

    381 . . . – – – section 3 maintenance when trailer towing your vehicle will need service more often when you're pulling a trailer. See the maintenance schedule for more on this. Check periodically to see that all hitch nuts and bolts are tight. When towing a trailer, the engine cooling system may te...

  • Page 382

    Starting and operating instructions . . . 382 towing your vehicle with two wheels on the ground and two wheels up on a dolly rear-wheel drive vehicles the vehicle can be towed with the rear wheels secured on a towing dolly. Use the following procedure: 1. Attach the dolly to the tow vehicle. Follow ...

  • Page 383

    383 . . . Section 4 - service and maintenance maintenance guidelines................................384 doing your own service work .....................384 accessories and modifications ......................385 fuel ................................................................385 fuel consumpti...

  • Page 384

    Service and maintenance . . . 384 ■ maintenance guidelines the required maintenance intervals vary considerably between climates, geographical locations, terrain and driving conditions. The export-specific maintenance schedule booklet provided with your vehicle shows the intervals required for the v...

  • Page 385

    385 . . . – – – – section 4 caution (continued) • be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused. If the wrong fasteners are used, parts can later break or fall off. You could be hurt. If doing some of your own service work, use the pr...

  • Page 386

    Service and maintenance . . . 386 notice use clean fuel only. Contami- nated fuel may reduce the life of the fuel delivery system and the engine. Notice do not use fuels containing more than 10% ethanol in your vehicle. Fuel containing the octane- enhancing additive called methylcyclopentadienyl man...

  • Page 387

    387 . . . – – – – section 4 for the 3.6 l v6 engine (code 7), use gasoline with a posted octane of 91 (research method) or higher. For best performance and when towing a trailer, use a gasoline with a posted octane of 93. For the 6.2l v8 engine, use gasoline with a posted octane of 95 (research meth...

  • Page 388

    Service and maintenance . . . 388 locking fuel door your vehicle is equipped with a locking fuel filler door. The fuel door is locked or unlocked every time the driver’s door is locked or unlocked with the power door locks or the transmitter. See the following in section 3 for more information: • re...

  • Page 389

    389 . . . – – – – section 4 after unlocking the fuel door, press on the rear edge of the fuel door and it will pop open. Remove the fuel filler cap by turning it slowly counter- clockwise. The cap has a spring in it. If you let go of the cap too soon, it will spring back to the right. Replace it by ...

  • Page 390

    Service and maintenance . . . 390 caution fuel vapor is highly flammable. Keep sparks, flames and smoking materials away from fuel. If you get gasoline on you and then something ignites it, you could be badly burned. To avoid injuries to you and others, read and follow all instructions on the gas st...

  • Page 391

    391 . . . – – – – section 4 caution static electricity can ignite gasoline vapor. You can be burned and your vehicle damaged. Before you open the fuel filler cap, touch a metal part on your vehicle to discharge the static electricity in your body. Do not return to your seat while refueling. If you r...

  • Page 392

    Service and maintenance . . . 392 ■ hood release to open the hood, first pull the handle inside the vehicle, located near the door on the driver's side of the instrument panel. Then pull up the secondary latch lever at the front of the vehicle and raise the hood. Caution an electric cooling fan can ...

  • Page 393

    393 . . . – – – – section 4 ■ engine compartment caution be careful not to drop or spill things that will burn onto a hot engine. They could start a fire and you or others could be burned. Engine cover your vehicle is equipped with an engine cover that may need to be removed in order to access some ...

  • Page 394

    Service and maintenance . . . 394 engine cover (cts-v model only) to access the engine oil and power steering fill caps, only the larger section of the engine cover needs to be removed. To remove the engine cover, do the following: 1. Raise the front of the engine cover to release the larger section...

  • Page 395

    395 . . . – – – – section 4 3.6 l v6 engine (2.8 l v6 engine similar) when you open the hood, you'll see: 1. Windshield washer reservoir 2. Engine compartment fuse block 3. Remote positive (+) battery terminal 4. Remote (-) negative battery terminal 5. Passenger compartment air filter 6. Engine cool...

  • Page 396

    Service and maintenance . . . 396 6.2 l v8 engine when you open the hood, you'll see: 1. Windshield washer reservoir 2. Underhood fuse block 3. Remote positive (+) battery terminal 4. Remote (-) negative battery terminal 5. Oil fill cap 6. Engine oil dipstick 7. Passenger compartment air filter 8. I...

  • Page 397

    397 . . . – – – – section 4 engine oil caution used oil filters and empty oil containers should not be disposed of with regular trash. Have the oil and oil filter changed by an authorized service center, familiar with the requirements of the law regard- ing used oil disposal, to help protect the env...

  • Page 398

    Service and maintenance . . . 398 the best time to check the engine oil level is when the oil is warm: 1. The vehicle should be on level ground. 2. Stop the engine and wait a few minutes for the oil to drain back into the oil pan. 3. If your vehicle is a cts-v model, you must remove the engine cover...

  • Page 399

    399 . . . – – – – section 4 notice if you use your vehicle for competitive driving, your engine may use more oil than it would with normal use. Low oil levels can damage the engine. Be sure to check the oil level often during competitive driving and keep the level at or near the upper mark that show...

  • Page 400

    Service and maintenance . . . 400 choosing the right oil viscosity sae 5w-30 is best for your vehicle. Your vehicle requires the use of a synthetic oil meeting gm standard gm4718m. Substitute oil not meeting gm standard gm4718m should not be used for an oil change. If you are unable to find oil of t...

  • Page 401

    401 . . . – – – – section 4 if an oil meeting gm standard gm4718m is not available, use an oil that meets the american petroleum institute service sm or gm-ll-a-025 service require- ments. Notice using engine oils of a viscosity other than those recommended could result in engine damage. The repairs...

  • Page 402

    Service and maintenance . . . 402 the oil and oil filter change intervals recommended in the maintenance schedule for your engine are based on the use of recommended quality oils and high quality filters. Using oil other than those recommended, or changing the oil and filter at longer intervals than...

  • Page 403

    403 . . . – – – – section 4 the cooling system in your vehicle is designed to use a coolant (a mixture of ethylene glycol, corrosion inhibitors and water) rather than plain water. Use a 50/50 mixture of clean water and dex-cool ® coolant. If you use this mixture, you don’t need to add anything else....

  • Page 404

    Service and maintenance . . . 404 locate the coolant surge tank and follow the arrow from the top of the tank, down the side to the horizontal mark. If the engine compartment is cool, the level should be at the froid/ full cold mark. If the coolant level is low, add a 50/50 mixture of water and dex-...

  • Page 405

    405 . . . – – – – section 4 intercooler system (cts-v model only) notice the intercooler system on the 6.2l v8 engine has a specific coolant fill procedure. Failure to follow this procedure may result in the engine overheating and in severe engine damage. See "intercooler system" under "engine overh...

  • Page 406

    Service and maintenance . . . 406 caution under some conditions the ethylene glycol in engine coolant is combustible. To avoid being burned, do not spill coolant on the exhaust system or on hot engine parts. If you have any doubt, have this operation performed by a qualified technician. 4. Reinstall...

  • Page 407

    407 . . . – – – – section 4 see the "recommended fluids and lubricants" chart later in this section to determine what kind of fluid to use. Notice damage caused by the use of any fluid that is not recommended is not covered by your new vehicle warranty. Manual transmission fluid (if equipped) it is ...

  • Page 408

    Service and maintenance . . . 408 the hydraulic clutch fluid system should be kept closed and sealed. Do not remove the cap to check the fluid level or to top off the fluid level. Check the hydraulic clutch fluid level in the reservoir at the intervals shown in the maintenance schedule. The level sh...

  • Page 409

    409 . . . – – – – section 4 rear axle lubricant it is not necessary to regularly check the rear axle fluid unless you suspect there is a leak in the system or you hear an unusual noise. Fluid loss in this system could indicate a problem. Have the system inspected. To check the fluid level: 1. Park t...

  • Page 410

    Service and maintenance . . . 410 to check the fluid level: 1. Turn off the ignition and let the engine compartment cool down. 2. If your vehicle is a cts-v model, you must remove the engine cover before you can access the fill cap. See "engine cover" earlier in this section. 3. Wipe the cap and the...

  • Page 411

    411 . . . – – – – section 4 it is not a good idea to "top off" your brake fluid. Adding brake fluid will not correct a leak. If you add fluid when the linings are worn, then there will be too much fluid when you get new brake linings. You should add (or remove) brake fluid, as necessary, only when w...

  • Page 412

    Service and maintenance . . . 412 the level should be at the proper mark. If it is low, bring it up to the proper level using dot-3 fluid from a sealed container. Dot-4 brake fluid is also compatible with the components of your brake system. Before adding dot-4 brake fluid, flush the brake hydraulic...

  • Page 413

    413 . . . – – – – section 4 notice • don’t mix water with ready- to-use washer fluid. It could freeze and damage washer system components. • when using a concentrated washer fluid, follow the man- ufacturer's instructions. • when it’s very cold outside, only fill the tank 3/4 full with fluid to allo...

  • Page 414

    Service and maintenance . . . 414 after a power loss, such as disconnecting the battery or removing the maxifuses in the fuse block, the following steps must be performed to calibrate the electronic throttle control. If this is not done, the engine will not run properly. 1. Turn the ignition on but ...

  • Page 415

    415 . . . – – – – section 4 to access the filter, do the following: 1. Turn the ignition off. 2. Open the hood. 3. Lift the front of the side cover of the air cleaner housing and remove. 4. Disconnect the electrical connector from the air box. 5. Loosen the screw on the clamp securing the air outlet...

  • Page 416

    Service and maintenance . . . 416 11. Away from the vehicle’s engine compartment, lightly shake the filter to release loose dust and dirt. Change the filter if it remains caked with dirt. For the type of filter to use, see "component specifica- tions" under "specifications and capacities" later in t...

  • Page 417

    417 . . . – – – – section 4 14. Once the filter has been replaced, align the tabs on the cover with the slots on the housing. 15. Reinstall the cover. Tighten the screws. 16. Install the hose on the air cleaner housing. Make sure the hose is routed correctly. 17. Install the air cleaner outlet duct....

  • Page 418

    Service and maintenance . . . 418 notice using the heating and air conditioning system without the passenger air filter installed may allow water or other debris to enter the system. This could cause a water leak or noises. Be sure to install a new air filter after removing the old one. To remove an...

  • Page 419

    419 . . . – – – – section 4 ■ recommended fluids and lubricants usage fluid / lubricant engine oil to determine the needed oil quality and viscosity for your vehicle's engine, see "engine oil" earlier in this section. Engine coolant 50/50 mixture of clean, drinkable water and use only dex-cool ® coo...

  • Page 420

    Service and maintenance . . . 420 manual transmission (cts-v model only) manual transmission fluid (gm part no. 88861800). Automatic transmission dexron ® -vi automatic transmission fluid. Transfer case (all-wheel drive) transfer case fluid (gm part no. 88861950). Key lock cylinders multi-purpose lu...

  • Page 421

    421 . . . – – – – section 4 hood latch assembly, secondary latch, pivots, spring anchor and release pawl lubriplate ® lubricant aerosol (gm part no. 12346293) or lubricant meeting requirements of nlgi grade 2, category lb or gc-lb. Hood and door hinges multi-purpose lubricant, superlube ® (gm part n...

  • Page 422

    Service and maintenance . . . 422 ■ tires your new vehicle comes with high- quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty, see the warranty booklet included with your vehicle’s owner’s manual or see your selling dealer. Caution poorly maintain...

  • Page 423

    423 . . . – – – – section 4 there may be an increase in road noise and a shorter tire tread life. Notice low-profile tires are more susceptible to damage from road hazards or curb impact than standard profile tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazar...

  • Page 424

    Service and maintenance . . . 424 notice improper tire pressure promotes adverse effects in tire life and vehicle performance. Excessively low inflation causes deflection of the tire and tire overheating which reduces tire strength and thus may damage the tires. It also causes tire overloading, abno...

  • Page 425

    425 . . . – – – – section 4 high speed operation caution driving at high speeds, 160 km/h (100 mph) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat buildup and can cause sudden tire failure. You could crash and you or others could be killed. Some hig...

  • Page 426

    Service and maintenance . . . 426 sensors, located on each wheel except the compact spare tire and wheel assembly, transmit tire pressure readings to a receiver in the vehicle. If the system detects low tire pressure in one or more of the tires, the low tire pressure warning light will appear and ch...

  • Page 427

    427 . . . – – – – section 4 if the warning light or the message does not disappear, make sure to check the tire pressure and inflate the tires to the recommended pressure as necessary. Check your tires at least once a month. Don't forget your spare tire (if equipped). You may use the driver informat...

  • Page 428

    Service and maintenance . . . 428 • the spare tire (if equipped) was installed on the vehicle. The spare tire does not have a tire pressure sensor. If you install the spare tire, the service tire monitor system message will appear on the driver information cen- ter. The message will go off once a ro...

  • Page 429

    429 . . . – – – – section 4 inspection and rotation check your tires and wheels regularly for unusual wear or damage. Don't forget your spare tire (if equipped). To make your tires last longer, have them inspected at the mileages recommended in your maintenance schedule. Do not rotate your tires if ...

  • Page 430

    Service and maintenance . . . 430 caution incorrect wheel nuts or improp- erly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. Notice improperly tightened wheel nuts can lead to brake pulsation and rot...

  • Page 431

    431 . . . – – – – section 4 • the tire has a bump, bulge or split. The tire information label says what size tires you need. To determine the location of your vehicle’s tire information label, see "vehicle loading" in section 3. It is recommended that you replace all four tires at the same time. Rep...

  • Page 432

    Service and maintenance . . . 432 caution if you add different sized wheels, and then if tires not recommended for those wheels are selected, your vehicle may not provide an acceptable level of performance and safety. You may increase the chance that you will crash and suffer serious injury. Only us...

  • Page 433

    433 . . . – – – – section 4 drive slowly and follow the cable manufacturer's instructions. If you hear the cables contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Notice to help avoid damage to your vehicle, drive slowly, don’t spin your wheels an...

  • Page 434

    Service and maintenance . . . 434 when using winter tires on your vehicle, be sure to use them on all four wheels. Winter tires with the same speed rating as the original tires may not be available for h, v, w, y and zr speed rated tires. If you choose snow tires with a lower speed rating, never exc...

  • Page 435

    435 . . . – – – – section 4 ■ wheels wheel alignment and tire balancing if there is unusual tire wear or if the vehicle pulls one way or the other, the alignment may need to be reset. If the vehicle vibrates when you are driving on a smooth road, the wheels may need to be balanced. If your vehicle i...

  • Page 436

    Service and maintenance . . . 436 caution putting a used wheel on the vehicle is dangerous. You would not know how the wheel had been used or how many miles it had been driven. The wheel could fail suddenly, causing a crash. Caution rust or dirt on the wheel, or on the parts to which it is fastened,...

  • Page 437

    437 . . . – – – – section 4 notice improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See "specifications and capacities" later in this section fo...

  • Page 438

    Service and maintenance . . . 438 ■ service parts identification label this label is located in the trunk. It is very helpful if you ever need to order parts. On this label, you will find the following information: • the vehicle identification num- ber • the model designation • paint information • a...

  • Page 439

    439 . . . – – – – section 4 you can remove fuses with a fuse extractor. Look at the silver-colored band inside the fuse. If the band is broken or melted , replace the fuse. Be sure you replace a bad fuse with a new one of the correct size and rating. If a fuse blows, have your vehicle serviced immed...

  • Page 440

    Service and maintenance . . . 440 1 2 3 4 5 12 20 32 39 42 49 48 66 6 13 7 14 8 15 9 16 17 10 18 21 22 23 24 25 26 28 29 30 37 11 19 31 38 41 60 50 57 58 59 34 35 36 33 40 43 51 61 52 62 69 70 71 73 74 75 56 46 47 54 55 64 65 67 44 45 53 63 68 72 27 akeng40_cts page 440 wednesday, july 23, 2008 11:4...

  • Page 441

    441 . . . – – – – section 4 engine compartment fuse block (cts model only) no. Circuits protected circuit breakers 5 headlight washer relays 1 cooling fan 2 2 cooling fan 1 3 starter 4 rear window defogger 12 horn 20 engine pump 21 cooling fan series/parallel 32 air conditioning compressor clutch 39...

  • Page 442

    Service and maintenance . . . 442 j cases 6 cooling fan 2 7 cooling fan 1 8 starter 9 windshield washer heater 10 antilock brake system motor 13 spare 14 not used 15 spare 16 brake vacuum pump 17 blower 18 rear window defogger 37 spare no. Circuits protected mini-fuses 11 spare 19 antilock brake sys...

  • Page 443

    443 . . . – – – – section 4 46 left high-beam headlight 47 right high-beam headlight 50 windshield washer pump 51 air bag switch 52 engine control module; transmission control module; instrument panel cluster; pass-key ® iii+ module no. Circuits protected 54 pass-key ® iii+ module; body control modu...

  • Page 444

    Service and maintenance . . . 444 1 2 3 4 5 12 20 32 39 42 49 48 66 6 13 7 14 8 15 9 16 17 10 18 21 22 23 24 25 26 28 29 30 37 11 19 31 38 41 60 50 57 58 59 34 35 36 33 40 43 51 61 52 62 69 70 71 73 74 75 56 46 47 54 55 64 65 67 44 45 53 63 68 72 27 akeng40_cts page 444 wednesday, july 23, 2008 11:4...

  • Page 445

    445 . . . – – – – section 4 no. Circuits protected circuit breakers 5 headlight washer relays 1 cooling fan 2 2 cooling fan 1 3 starter 4 rear window defogger 12 horn 20 intercooler pump 21 cooling fan series/parallel 32 air conditioning compressor clutch 53 spare 63 ignition 1 66 windshield wiper 6...

  • Page 446

    Service and maintenance . . . 446 13 spare 14 electric parking brake 15 spare 16 spare 17 blower 18 rear window defogger 37 magnetic ride/ suspension control mini-fuses 11 spare 19 antilock brake system 22 display 23 spare 24 body control module 1 no. Circuits protected 25 adaptive forward lighting ...

  • Page 447

    447 . . . – – – – section 4 52 engine control module; transmission control module; instrument panel cluster; pass-key ® iii+ module 54 pass-key ® iii+ module; body control module 55 navigation motor 56 windshield wiper 57 right low-beam headlight no. Circuits protected 58 left low-beam headlight 59 ...

  • Page 448

    Service and maintenance . . . 448 rear compartment fuse block (cts model only) no. Circuits protected circuit breakers 1 left front power seat 2 right front power seat 3 power windows 4 power steering column no. Circuits protected 32 left rear window 37 right rear window relays 5 trunk release 6 loc...

  • Page 449

    449 . . . – – – – section 4 21 sunroof 22 rear fog lights 23 regulated voltage control sensor 24 audio system 25 air bag system 26 remote keyless entry system (if equipped); pass-key ® iii+ theft deterrent feature module no. Circuits protected 27 audio system speakers 28 television tuner (if equippe...

  • Page 450

    Service and maintenance . . . 450 rear compartment fuse block (cts-v model only) no. Circuits protected circuit breakers 1 left front power seat 2 right front power seat 3 power windows no. Circuits protected 4 power steering column 32 left rear window 37 right rear window relays 5 trunk release 6 l...

  • Page 451

    451 . . . – – – – section 4 17 fuel pump 18 spare 19 stoplights 20 right position light 21 fuel system control module 22 rear fog lights 23 regulated voltage control sensor 24 audio system 25 air bag system no. Circuits protected 26 remote keyless entry system (if equipped); pass-key ® iii+ theft de...

  • Page 452

    Service and maintenance . . . 452 ■ bulb replacement see your dealer for any bulb changing procedure not listed in this section. Headlight aiming is important to safe driving. See your dealer for service. Halogen bulbs caution halogen bulbs contain pressurized gas and may burst if dropped or scratch...

  • Page 453

    453 . . . – – – – section 4 2. Peel the protection shield away from the vehicle to access the light assembly. 3. Reach through the opening to disconnect the electrical connector from the old bulb. 4. Remove the bulb socket from the lamp housing. Turn the bulb one-quarter turn to the left and remove ...

  • Page 454

    Service and maintenance . . . 454 license lights 1. Push the tab to remove the license plate light. 2. Rotate the light assembly down and remove it. 3. Turn the socket counterclock- wise and remove it. 4. Remove and replace the bulb. Pull the bulb straight out of the socket. 5. When reinstalling the...

  • Page 455

    455 . . . – – – – section 4 ■ replacement bulb specifications see your dealer for any bulb not listed in this section. License plate lights..................................................................................................................W5w ll front fog lights ..........................

  • Page 456

    Service and maintenance . . . 456 ■ specifications and capacities component specifications 2.8 l v6 engine engine code.......................................................................................................................................T transmission ...................................

  • Page 457

    457 . . . – – – – section 4 component specifications (continued) 3.6 l v6 engine engine code.......................................................................................................................................7 transmission .............................................................

  • Page 458

    Service and maintenance . . . 458 component specifications (continued) 3.6 l v6 engine engine code...................................................................................................................................... V transmission .......................................................

  • Page 459

    459 . . . – – – – section 4 component specifications (continued) 6.2 l v8 engine engine code.......................................................................................................................................P transmission .............................................................

  • Page 460

    Service and maintenance . . . 460 capacities* (approximate) fuel tank ...................................................................................................................................68.1 l cooling system 2.8l v6 engine .................................................................

  • Page 461

    461 . . . – – – – section 4 ■ fuel consumption and emissions information 2.8 l engine engine code ...........................................................................................................................................T fuel consumption manual transmission urban .....................

  • Page 462

    Service and maintenance . . . 462 3.6 l engine engine code ...........................................................................................................................................7 fuel consumption automatic transmission urban .........................................................

  • Page 463

    463 . . . – – – – section 4 3.6 l engine engine code .......................................................................................................................................... V fuel consumption manual transmission urban ..................................................................

  • Page 464

    Service and maintenance . . . 464 3.6 l engine (continued) co 2 mass emissions manual transmission urban (actual) ................................................................................................................... 429 g/km extra-urban (actual) ...........................................

  • Page 465

    465 . . . – – – – section 4 6.2 l engine engine code ...........................................................................................................................................P fuel consumption manual transmission urban ..................................................................

  • Page 466

    Service and maintenance . . . 466 ■ appearance care caution care should be taken to avoid contamination of the safety belt webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing be...

  • Page 467

    467 . . . Section 5 - problems on the road jump starting ................................................468 towing...........................................................472 engine overheating ......................................473 checking and adding coolant ......................475 checkin...

  • Page 468

    Problems on the road . . . 468 ■ jump starting if your battery has run down, you may use another vehicle and some jumper cables to start your vehicle. The other vehicle must have a 12-volt battery with a negative ground system. Notice if the other vehicle does not have a 12-volt battery with a negat...

  • Page 469

    469 . . . – – – – – section 5 to jump start your vehicle, follow these steps: notice ignoring these steps could result in costly damage to your vehicle. The repairs would not be covered by your warranty. 1. Get the vehicles close enough so the jumper cables can reach. Be sure the vehicles aren't tou...

  • Page 470

    Problems on the road . . . 470 3. Now open the hoods and locate the positive (+) and negative (-) battery terminals. Caution an electric cooling fan can start even if the engine is not running. Be careful around any underhood electric fan. Caution fans or other moving engine parts can injure you bad...

  • Page 471

    471 . . . – – – – – section 5 notice do not connect positive (+) to negative (-) or you will get a short that would damage the battery and possibly other parts. Do not connect the negative (-) cable to the negative (-) terminal on the dead battery because this can cause sparks. 4. Connect the positi...

  • Page 472

    Problems on the road . . . 472 7. Attach the other end of the negative cable to a heavy metal part on the engine of the vehicle with the discharged battery, or to a remote negative (-) ground location if the vehicle has one. Attach the cable at least 45 cm (18 inches) away from the dead battery, but...

  • Page 473

    473 . . . – – – – – section 5 ■ engine overheating caution steam from an overheated engine can burn you badly. Stay away from the engine if you see or hear steam coming from it. Caution continued operation of an overheated engine, even for a short time, may result in a fire and the possibility of pe...

  • Page 474

    Problems on the road . . . 474 if the light stays on or the coolant temperature gage still shows an overheat condition, pull over, stop and park your vehicle right away. If there is still no sign of steam, run the engine at idle speed for about 3 minutes. If the overheat warning continues, turn off ...

  • Page 475

    475 . . . – – – – – section 5 overheat protection mode if you still have the overheat warning, the engine has a feature whereby it alternates firing groups of cylinders to minimize engine damage and to allow you to drive your vehicle to the nearest service center. You will notice a significant loss ...

  • Page 476

    Problems on the road . . . 476 notice do not substitute any liquids for the proper coolant mixture. Otherwise, premature corro- sion may result and the engine coolant will require change sooner. Damage caused by the use of any coolant that is not recom- mended is not covered by your new vehicle warr...

  • Page 477

    477 . . . – – – – – section 5 if coolant is visible in the surge tank: if coolant is visible in the tank but the level is not up to the froid/ full cold mark, wait a while for the engine to cool, then add a 50/50 mixture of clean water and dex-cool ® coolant at the coolant surge tank. See "engine co...

  • Page 478

    Problems on the road . . . 478 4. Start the engine and let it run until you can feel that the upper radiator hose is getting hot (watch out for the engine cooling fans). By this time, the coolant level inside the coolant tank will be lower. Caution the electric engine cooling fan can start even if t...

  • Page 479

    479 . . . – – – – – section 5 checking and adding coolant to intercooler system (cts-v model only) notice the intercooler system on the 6.2l v8 engine has a specific coolant fill procedure. Failure to follow this procedure may result in the engine overheating and in severe engine damage. Turn off th...

  • Page 480

    Problems on the road . . . 480 caution • do not substitute any liquids for the proper coolant mixture. The engine could catch on fire and you or others could be burned. • do not spill coolant on hot engine parts. Caution the electric engine cooling fan can start even if the engine is not running. Be...

  • Page 481

    481 . . . – – – – – section 5 notice the intercooler system cap is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheat- ing. Be sure the cap is hand tightened and fully seated.If the coolant is not at the proper level when the system coo...

  • Page 482

    Problems on the road . . . 482 avoid further tire and wheel damage by driving very slowly to a level place to change your tire. Turn on your hazard warning flashers. Caution changing a tire can cause inju- ry. The vehicle can slip off the jack and injure you or other people. Caution to help prevent ...

  • Page 483

    483 . . . – – – – – section 5 jack and spare tire removal 1. Remove the spare tire cover. 2. Turn the wing nut counter- clockwise and remove it. 3. Remove the compact spare tire . Place the compact spare tire on the ground near the flat tire. 4. Remove the jack , wheel wrench and extension . E d c b...

  • Page 484

    Problems on the road . . . 484 changing the flat tire 1. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Loosen the wheel nuts, but do not remove them yet. To avoid removing the wheel wrench while loosening the nuts, rotate the wheel wrench handle 180°, then flip the handle back to ...

  • Page 485

    485 . . . – – – – – section 5 notice if you try to raise the vehicle with the jack positioned under the rocker molding, the molding could break and the vehicle could be damaged. Position the jack so that the jack head will rise to the notch (inboard of the rocker molding) in the vehicle's frame. 4. ...

  • Page 486

    Problems on the road . . . 486 notice if the doors are locked with the security system armed, the alarm will activate when the vehicle is raised by the jack. 8. Remove the wheel nuts and take off the tire. 9. Remove any dirt or rust from the wheel bolts, mounting surfaces and spare wheel. Akeng40_ct...

  • Page 487

    487 . . . – – – – – section 5 caution rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to th...

  • Page 488

    Problems on the road . . . 488 caution incorrect wheel nuts or improp- erly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. If you have to replace them, be sure to get original equipment wheel nuts. Stop somewhere as soon as you can and hav...

  • Page 489

    489 . . . – – – – – section 5 storing tire and jacking equipment caution storing a jack, a tire or other equipment in the passenger's compartment of the vehicle could cause injury. In a sudden stop or collision, loose equip- ment could strike someone. Store all these in the proper place. Flat tire s...

  • Page 490

    Problems on the road . . . 490 compact spare tire storage store the spare tire and tools in the storage compartment on the trunk floor. 1. Open the trunk. 2. Make sure the foam support is on the storage compartment floor. 3. Restow the jack , wheel wrench and extension . Restow the tie-down strap . ...

  • Page 491

    491 . . . – – – – – section 5 compact spare tire (if equipped) although the compact spare was fully inflated when your vehicle was new, it can lose air after time. Check the inflation pressure regularly. It should be 420 kpa (60 psi). The compact spare should not be driven at speeds over 80 km/h (50...

  • Page 492

    Problems on the road . . . 492 tire sealant and compressor kit (cts-v model only) caution idling the engine inside an enclosed area such as a garage, and/or with the climate control system's fan off, may produce dangerous exhaust fumes. Caution be careful not to overinflate things. They could explod...

  • Page 493

    493 . . . – – – – – section 5 the tire sealant and compressor kit uses a liquid tire sealant and air to seal small punctures in the tread area of a tire. The tire sealant cannot repair tire damage caused while driving on a flat tire, a tire that has had a blow out or a tire that has punctures in the...

  • Page 494

    Problems on the road . . . 494 be aware of the following concerning tire sealant: • tire sealant is only a temporary fix. • the tire sealant solution is a one-time use application for one tire only. • the tire sealant may not be as effective beyond the expiration date. Check the expiration date on t...

  • Page 495

    495 . . . – – – – – section 5 the tire sealant and compressor kit equipped with an air or sealant selector switch has the following features: 1. Selector switch 2. On/off button 3. Air pressure gage 4. Air pressure deflation button 5. Tire sealant canister 6. Black air only hose 7. Clear sealant/air...

  • Page 496

    Problems on the road . . . 496 the kit can also be used without the sealant. See "using the air compressor without tire sealant" later in this section. The compressor kit may be equipped with an accessory adapter located in a compartment on the bottom the compressor. With this feature, you can infla...

  • Page 497

    497 . . . – – – – – section 5 - compressor kits not equipped with a selector switch: squeeze the tabs on the buckle to release the strap on the tire sealant and compressor kit. 4. Remove the tire sealant and compressor kit from the vehicle. Using the tire sealant and compressor kit caution be sure t...

  • Page 498

    Problems on the road . . . 498 4. Remove the tire sealant and compressor kit and place the kit near the flat tire. See the following, earlier in this section, for more information: - removing the tire sealant and compressor kit 5. Unwrap the clear air/sealant filling hose and the accessory plug from...

  • Page 499

    499 . . . – – – – – section 5 13. Press i (on) or the on/off button to turn the system on. The compressor will force sealant and air into the tire. Tire sealant may leak from the puncture hole until the vehicle is driven and the hole has been sealed. Initially, the pressure gage reading will be high...

  • Page 500

    Problems on the road . . . 500 16. Press o (off) or the on/off button to turn the air compressor off. Note: complete the following steps quickly. The tire will not be sealed and air may leak from the puncture until the vehicle is driven and the sealant has been distributed in the tire. Caution be ca...

  • Page 501

    501 . . . – – – – – section 5 23. Attach the maximum speed label (if equipped) to a highly visible location within the vehicle. 24. Restow the tire sealant and compressor kit in reverse order as removal. Caution storing the tire sealant and compressor kit or other equipment in the passenger's compar...

  • Page 502

    Problems on the road . . . 502 make sure that you dispose of the used sealant canister in accordance with local regulations. Ask your dealer, a service station or a local recycling center for proper disposal information. After using the tire sealant, be sure to replace the sealant canister in the ti...

  • Page 503

    503 . . . – – – – – section 5 6. Remove the valve cap from the tire valve stem. Make sure the valve stem is positioned close to the ground so the hose will reach the tire. 7. Firmly attach the air inflator hose to the tire valve stem. - compressor kits equipped with a selector switch: to tighten, tu...

  • Page 504

    Problems on the road . . . 504 13. Inflate the tire to the recommended inflation pressure as shown on the tire and loading information label. See "tire and loading information label" in section 3 for more information. 14. Check the tire pressure using the air pressure gage on the tire sealant and co...

  • Page 505

    505 . . . – – – – – section 5 17. Disconnect the hose from the tire valve. - compressor kits equipped with a selector switch: turn the end of the hose counterclockwise to disconnect it from the tire valve stem. - compressor kits not equipped with a selector switch: pull the lever up to unlock the ai...

  • Page 506

    Problems on the road . . . 506 to replace the tire sealant canister, do the following: 1. Remove the tire sealant and compressor kit from the vehicle. See the following, earlier in this section, for more information: - removing the tire sealant and compressor kit 2. Unwrap the hose from the compress...

  • Page 507

    507 . . . – – – – – section 5 3. Remove the sealant canister from the air compressor. - compressor kits equipped with a selector switch: press the yellow button to release the sealant canister. - compressor kits not equipped with a selector switch: rotate the sealant canister so that the inflator ho...

  • Page 508

    Problems on the road . . . 508 • compressor kits not equipped with a selector switch: - rotate the sealant canister so that the sealant filling hose is aligned with the slot in the compressor. - push the sealant canister down and rotate the canister clockwise. - wrap the sealant filling hose around ...

  • Page 509

    509 . . . – – – – – section 5 rocking your vehicle to free your vehicle when it is stuck: 1. Turn the steering wheel left and right to clear the area around the front wheels. 2. Press the tc button to turn the traction control and stability systems off. If your vehicle is a cts-v model, the button i...

  • Page 510

    Problems on the road . . . 510 ■ if you cannot start your vehicle using the keyless ignition system when the transmitter battery is low, or if the system is not detecting the transmitter because the vehicle is very close to a radio/tv tower, you may not be able to start the vehicle. The driver infor...

  • Page 511

    511 . . . – – – – – section 5 data is recorded only if a non-triv- ial crash situation occurs. In most cases, data is recorded for only about 30 seconds. Special equipment is needed to retrieve this data. Law enforcement agencies or others may have equipment that can retrieve the information if they...

  • Page 512

    Akeng40_cts page 512 wednesday, july 23, 2008 11:47 am.

  • Page 513

    513 . . . Index a acceleration - lateral acceleration gage ..............56 accessories ........................................................385 accessories - retained accessory power .....243, 342 accessory power outlet .....................................116 adaptive forward lighting system .....

  • Page 514

    Index . . . 514 b battery ..............................................................413 battery - charging system light ..........................34 battery - electric power management ................244 battery - jump starting ......................................468 battery - remote negative...

  • Page 515

    515 . . . Index c (continued) cautions - exhaust warnings ...............................12 cautions - important safety precautions ...........6-20 cd player - playing mp3 or wma format cds (6-disc cd changer) .......................................156 cd player - playing mp3 or wma format cds (hard...

  • Page 516

    Index . . . 516 c (continued) coolant - intercooler system .............................405 coolant - intercooler system pressure cap ........396 cruise control ...................................................218 cruise control - buttons ......................................25 cruise control - i...

  • Page 517

    517 . . . Index e (continued) engine - checking and adding coolant to intercooler system ..........................................479 engine - coolant ...............................................402 engine - coolant temperature gage .............28, 56 engine - coolant temperature warning light ...

  • Page 518

    Index . . . 518 f (continued) fluid - engine oil ...............................................397 fluid - heated washer fluid .................92, 132, 217 fluid - hydraulic clutch fluid ............................407 fluid - manual transmission fluid ......................407 fluid - power steer...

  • Page 519

    519 . . . Index h (continued) headlights - high/low beam control ................213 headlights - leveling control ......................85, 121 headlights - washer ..................................122, 218 headlights - wiper-activated headlights ....122, 215 heater - engine block heater .............

  • Page 520

    Index . . . 520 k keyless access system .......................................329 keyless access system - transmitter ..................329 keyless entry - battery replacement ..........327, 333 keyless entry - transmitter .................................324 keyless entry - transmitter frequency a...

  • Page 521

    521 . . . Index l (continued) lights - daytime running lights ........................120 lights - exterior lights .......................................243 lights - fog lights .............................................123 lights - front fog lights ....................123, 452, 455 lights - haza...

  • Page 522

    Index . . . 522 m (continued) maintenance - engine coolant reservoir .....17, 460 maintenance - engine coolant surge tank .....................395, 396 maintenance - engine oil ..........................397, 460 maintenance - engine oil dipstick .............395, 396 maintenance - engine oil fill ca...

  • Page 523

    523 . . . Index n navigation - navigation display dimmer control ..................25 navigation - navigation screen up/down button .................25 navigation - navigation system ..................25, 207 net - convenience net ......................................238 o object detection - pedest...

  • Page 524

    Index . . . 524 p (continued) programmable features - seat exit position recall .....................................74 programmable features - seat exit position setup .....................................75 r radio ..........................................................25, 136 radio - antenna ....

  • Page 525

    525 . . . Index r (continued) restraints - securing a child restraint with lower attaching points and top strap ............307 restraints - shoulder belt comfort guides .........272 restraints - shoulder belt height adjuster ..........271 restraints - supplemental restraints ..................277 r...

  • Page 526

    Index . . . 526 s (continued) seats - seat position recall ...................................77 seats - split folding rear seatback ....................266 security - immobilizer system ...........................320 security - intrusion sensor .................................318 security - intrus...

  • Page 527

    527 . . . Index s (continued) stability - stabilitrak system ...............................114 starting - engine flooding .................................344 starting - engine starting ..................................342 starting - engine starting problems ...........344, 510 starting - failure ...

  • Page 528

    Index . . . 528 t (continued) terminals - remote positive battery terminal ............395, 396 theft deterrent - immobilizer system ................320 theft deterrent - intrusion sensor .....................318 theft deterrent - intrusion sensor override .......319 theft deterrent - theft deterren...

  • Page 529

    Index . . . 529 t (continued) traction - stabilitrak ® / traction control system light ...................41, 115 traction - tire chains or similar traction devices ............432 traction - traction control system ............110, 210 trailer - hitches ................................................

  • Page 530

    Index . . . 530 v vehicle - new vehicle break-in period ................313 vehicle - rocking ...............................................509 vehicle identification number ...........................437 vehicle remote-start .........................................336 ventilation - air vents .......