- DL manuals
- CalAmp
- Modem
- SMC-GPRS Series
- User manual
CalAmp SMC-GPRS Series User manual - page 41
001-0004-829 Rev00
Page 41 of 84
ATS7
Set number of seconds to wait for connection completion:
=000 to 060
ATS8
Set number of seconds to wait for comma dialing modifier:
=0 DCE does not pause when "," encountered in dial string
=1 to 255 Number of seconds to pause
ATS10
Set disconnect delay after indicating the absence of data carrier:
=001 to 254 Number of tenths of seconds of delay
ATO
Switch from command mode to data mode / PPP online mode:
ATO is the corresponding command to the +++ escape sequence: When you
have established a CSD call or a GPRS connection and TA is in command mode,
ATO causes the TA to resume the data or GPRS connection and takes you back
to data mode or PPP online mode.
+++
Switch from data mode to command mode:
This command is only available during a CSD call or a GPRS connection. The
+++ character sequence causes the TA to cancel the data flow over the AT
interface and switch to command mode. This allows you to enter AT commands
while maintaining the data connection to the remote device or, accordingly, the
GPRS connection. To prevent the +++ escape sequence from being
misinterpreted as data, it must be preceded and followed by a pause of at least
1000 ms. The +++ characters must be entered in quick succession, all within
1000 ms.
AT+CBST
Select bearer service type:
AT+CBST=
speed:
=1 300 bps (V.21)
=2 1200 bps (V.22)
=4 2400 bps (V.22bis)
=6 4800 bps (V.32)
=7 9600 bps (V.32)
=14 14400 bps (V.34)
=65 300 bps (V.110)
=66 1200 bps (V.110)
=68 2400 bps (V.110)
=70 4800 bps (V.110)
=71 9600 bps (V.110)
=75 14400 bps (V.110)
AT+CRLP
Select radio link protocol parameters for originated non-transparent data calls.
AT+CLCC
List current calls of ME:
The execute command returns a list of current calls of ME. If command is
successful, but no calls are available, no information response is sent to TE.
AT+CR
Service reporting control:
Configures the TA whether or not to transmit an intermediate result code +CR:
=0 Disable
=1 Enable
Setting the value to 1 may lead to connection failure, if the application (e.g.
WinFax) waits for default result code/URC.
At+CRC
Set Cellular Result Codes for incoming call indication:
The command controls whether or not to use the extended format of incoming
call indication.
=0 Disable extended format
=1 Enable extended format
Setting the value to 1 may lead to connection failure, if the application (e.g.
WinFax) waits for default result code/URC.
Summary of SMC-GPRS Series
Page 1
S s m m c c - - g g p p r r s s - - x x x x x x l a n d c e l l s m c e m b e d d e d w i r e l e s s m o d e m g s m g p r s u n i v e r s a l s o c k e t user manual 001-0004-829 rev00; october 2009.
Page 2
Revision history rev00 released 10/06/2009 c. Pollock.
Page 3
Table of contents section 1 - preface ...........................................................................................5 copyright notice...................................................................................................5 modem use..............................................
Page 4
Table of contents section 10 - at command reference..............................................................34 at command types ............................................................................................34 command line syntax .......................................................
Page 5
001-0004-829 rev00 page 5 of 84 s s e e c c t t i i o o n n 1 1 - - p p r r e e f f a a c c e e copyright notice ©2009 calamp. All rights reserved. This manual covers the operation of the calamp smc-gprs embedded wireless modem. Specifications described are typical only and are subject to normal man...
Page 6
001-0004-829 rev00 page 6 of 84 mobile application safety • do not change parameters or perform other maintenance of the smc-gprs while driving. • road safety is crucial. Observe national regulations for cellular telephones and devices in vehicles. • avoid potential interference with vehicle electro...
Page 7
001-0004-829 rev00 page 7 of 84 s s e e c c t t i i o o n n 2 2 - - a a b b b b r r e e v v i i a a t t i i o o n n s s abbreviation description apn access point name cdma code division multiple access csd circuit switched data cts clear to send dcd data carrier detect dce data communication equipme...
Page 8
001-0004-829 rev00 page 8 of 84 s s e e c c t t i i o o n n 3 3 - - p p r r o o d d u u c c t t o o v v e e r r v v i i e e w w module identification label information the label contains the calamp part number, serial number, fcc id, and the imei number. Imei: the international mobile equipment iden...
Page 9
001-0004-829 rev00 page 9 of 84 smc module description top side reference fig. 2.1 smc-gprs top side smc-gprs top side components: 1. Power: green led indicating cell module power on. 2. Dcd: red led indicating data carrier detect from cellular network. 3. Rf (antenna): mmcx socket, primary antenna ...
Page 10
001-0004-829 rev00 page 10 of 84 bottom side reference fig. 2.2 smc-gprs bottom side smc-gprs bottom side socket pins: 1. Vcc/gnd pins 2. –reset/gnd pins 3. Serial pins figure 2.3 smc pins, top view 2 1 3.
Page 11
001-0004-829 rev00 page 11 of 84 pin descriptions pin # pin name i/o type description 24 -reset input this signal is used to force a reset procedure by providing a low level for at least 10 ms. Data stored in volatile memory will be lost. This line must be driven by an open drain or open collector. ...
Page 12
001-0004-829 rev00 page 12 of 84 s s e e c c t t i i o o n n 4 4 - - d d e e v v e e l l o o p p m m e e n n t t / / t t e e s s t t b b o o a a r r d d i i n n t t e e r r f f a a c c e e development/test board the development/test board is required to interface the scm-gprs modem to a standard rs2...
Page 13
001-0004-829 rev00 page 13 of 84 rs-232 serial port integration parameters table 4.2 provides the serial cable design information for the smc-gprs using the dk test board. Table 4.2 standard rs-232 de-9 pin out pin name direction description 1 cd «— carrier detect 2 rx «— receive data 3 tx —» transm...
Page 14
001-0004-829 rev00 page 14 of 84 s s e e c c t t i i o o n n 5 5 - - g g e e t t t t i i n n g g s s t t a a r r t t e e d d u u s s i i n n g g t t h h e e s s m m c c t t e e s s t t b b o o a a r r d d this section describes the use of the smc test board to set up the smc modem for internet acces...
Page 15
001-0004-829 rev00 page 15 of 84 verify smc modem connectivity power on the smc test board (+12vdc typical) and observe the hyperterminal window for ^sysstart , indicating the smc modem successfully powered on. Figure 5.2 hyperterminal screen responses the ati command prints the cell module product ...
Page 16
001-0004-829 rev00 page 16 of 84 confirm that the sim’s pin has been authenticated by the network using the at+cpin? Command. The reply should read “+cpin: ready”. See section 6 for sim related information if “ready” does not display. Verify good signal strength with the at+csq command. A typical re...
Page 17
001-0004-829 rev00 page 17 of 84 connect using the dial-up-network connection go to the network connections screen and double click on the newly created dial-up connection (i.E. Smc-gprs). When the connect window appears, set the username and password as defined for your carrier (usually blank). Ent...
Page 18
001-0004-829 rev00 page 18 of 84 the modem will attempt to connect to the provider network. If the configured baud rate for the com port, the modem, and the dun do not match, the dun will not be able to talk to the modem properly and you will get a hardware error message. Otherwise the dun will cont...
Page 19
001-0004-829 rev00 page 19 of 84 right click on the connected dial-up connection icon and select the details tab. The status of the connection will be displayed, including the ip address assigned by the carrier network..
Page 20
001-0004-829 rev00 page 20 of 84 s s e e c c t t i i o o n n 6 6 - - s s i i m m c c a a r r d d s s p p e e c c i i f f i i c c i i n n f f o o r r m m a a t t i i o o n n the sim card can be used to store a personal idetification number (pin) to authenticate users on the network. The at+cpin write...
Page 21
001-0004-829 rev00 page 21 of 84 what to do if pin or password authentication fails? Pin1 / puk1: after three failures to enter pin 1, the sim card is blocked (except for emergency calls). +cme error: 12 will prompt the client to unblock the sim card by entering the associated puk (= pin unblocking ...
Page 22
001-0004-829 rev00 page 22 of 84 sim locks: these are factory set locks, such as "pf", "pn", "pu", "pp", "pc". An 8-digit unlocking code is required to operate the mobile with a different sim card, or to lift the lock. The code can only be obtained from the provider. Failure to enter the password is...
Page 23
001-0004-829 rev00 page 23 of 84 s s e e c c t t i i o o n n 7 7 - - c c a a l l l l s s e e t t u u p p i i n n f f o o r r m m a a t t i i o o n n this section provides a brief look at setting up variuos call scienerios using the smc-gprs modem with the smc development/test board and hyperterminal...
Page 24
001-0004-829 rev00 page 24 of 84 select atv0 to set the short format (numeric code) or atv1 to set the long format (verbose code) of result codes. In case of using the command without parameter the value will be set to 0. Generally, only at+cbst=0 (auto bauding) and at+cbst = 7 (9600 bps, [v.110]) a...
Page 25
001-0004-829 rev00 page 25 of 84 general packet radio service (gprs) before proceeding, be sure the cellular account sim is provisioned with gprs data services and all necessary initialization commands have been executed. The module must then be attached to the gprs service, allowing the device to b...
Page 26
001-0004-829 rev00 page 26 of 84 define the gprs context exact settings of gprs context and quality of service profiles are provisioned by the network provider and must be requested before defining the gprs context. Every pdp context has a context identifier . The context identifiers are numbered se...
Page 27
001-0004-829 rev00 page 27 of 84 short message service (sms) sms is a service to transfer short messages between a gsm mobile stations (ms) and an short- message-entity (sme) via a service center (sc). Smc modems support two modes: text mode and protocal data unit (pdu) mode. The minimal requirement...
Page 28
001-0004-829 rev00 page 28 of 84 if you want to receive cell broadcast messages activate the urc presentation for cbs with at+cnmi and subscribe to a cbs channel with at+cscb. The at^sm20 command specifies different modes of responses returned when sending and writing short messages: at^sm20=,0 caus...
Page 29
001-0004-829 rev00 page 29 of 84 internet services the modem has an embedded tcp/ip stack that is driven by at commands and enables the host application to easily access the internet. The advantage of this solution is that it eliminates the need for the application manufacturer to implement their ow...
Page 30
001-0004-829 rev00 page 30 of 84 • the tcp/ip stack of tc63i supports using several service profiles at the same time, provided all of them are running on the same connection profile. For example, it is possible to download files from an ftp server, while sending and receiving emails at the same tim...
Page 31
001-0004-829 rev00 page 31 of 84 s s e e c c t t i i o o n n 8 8 - - s s m m c c m m o o d d e e m m m m o o d d u u l l e e p p r r o o f f i i l l e e s s in addition to the default profile, you can store an individual one with at&w. To alternate between the two profiles enter either atz (loads us...
Page 32
001-0004-829 rev00 page 32 of 84 s s e e c c t t i i o o n n 9 9 - - c c o o m m m m o o n n a a t t c c o o m m m m a a n n d d r r e e f f e e r r e e n n c c e e g g u u i i d d e e below you will find a reference guide of the at commands most commonly used in day-to-day operation of the modem. T...
Page 33
001-0004-829 rev00 page 33 of 84 network service commands at+csq signal quality example response; +csq: 25,0 has an rssi of -63 dbm at^smong cell info table example response: gprs monitor bcch g pbcch pat mcc mnc nom ta rac # cell # 0637 1 - 4 234 05 2 00 0b bcch - arfcn of bcch carrier g - gprs sta...
Page 34
001-0004-829 rev00 page 34 of 84 s s e e c c t t i i o o n n 1 1 0 0 - - a a t t c c o o m m m m a a n n d d r r e e f f e e r r e e n n c c e e all modem functions are controlled using the same industry-standard at commands that are used to control landline modems. A knowledge of all these commands...
Page 35
001-0004-829 rev00 page 35 of 84 result codes after issuing a command, a result code will typically be displayed on the screen to inform you if the command was successful, unsuccessful, improperly formatted, etc. When in the command mode, thirteen possible result codes may be returned. The result co...
Page 36
001-0004-829 rev00 page 36 of 84 3 - connect result code returned, dial tone detection is disabled, busy detection is enabled. 4 - connect result code returned, dial tone and busy detection are both enabled. At\v set connect result code format: 0 - connect result code returned without rlp trailer. 1...
Page 37
001-0004-829 rev00 page 37 of 84 status control commands the at commands described in this section allow the external application to obtain various status information from the modems cellular module. Table 10.4: status control commands command description at+cmer mobile equipment event reporting: at...
Page 38
001-0004-829 rev00 page 38 of 84 serial interface control commands the at commands described in this section allow the external application to determine various settings related to the modems's serial interface. Table 10.5: serial interface control commands command description at\q flow control: 0 -...
Page 39
001-0004-829 rev00 page 39 of 84 at+ilrr set te-ta local rate reporting: 0 - disables reporting of local port rate 1 - enables reporting of local port rate 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200, 230400, 460800 rates supported at+ipr set fixed local rate: 300, 60...
Page 40
001-0004-829 rev00 page 40 of 84 identification commands the at commands described in this section allow the external application to obtain various identification information related to the modem and linked entities. Table 10.7: identification commands command description ati the execute command del...
Page 41
001-0004-829 rev00 page 41 of 84 ats7 set number of seconds to wait for connection completion: =000 to 060 ats8 set number of seconds to wait for comma dialing modifier: =0 dce does not pause when "," encountered in dial string =1 to 255 number of seconds to pause ats10 set disconnect delay after in...
Page 42
001-0004-829 rev00 page 42 of 84 at+csns single numbering scheme: the command enables the me to accept incoming calls when no bearer capability information is provided with the call, e.G. Single numbering scheme calls or calls originitating from analog devices. =0 voice: each call received without b...
Page 43
001-0004-829 rev00 page 43 of 84 at^sops extended operator selection similar to at^cops. At+creg network registration: the read (?) command serves to verify the network registration status of the me. 0 - not registered, me is currently not searching for new operator and user intervention is required...
Page 44
001-0004-829 rev00 page 44 of 84 at^monp monitor neighbour cells: the command supplies information of up to six neighbour cells. There are two ways to retrieve the information: once on request by using the execute command or automatically every seconds by using the write command. To stop the periodi...
Page 45
001-0004-829 rev00 page 45 of 84 internal internet service commands a brief description of the internet service commands are provided in table 10.10. For futher information, refer to the cinterion tc63i at command set document available from cinterion [2]. Table 10.10: internet service commands comm...
Page 46
001-0004-829 rev00 page 46 of 84 gprs commands this section describes at commands that a te (terminal equipment, e.G. An application running on a controlling pc) may use to control the modem acting as a gprs mobile termination (mt). A brief description of the gprs commands are provided in table 10.1...
Page 47
001-0004-829 rev00 page 47 of 84 at+cgauto automatic response to a network request for pdp context activation: the test command returns the values of supported by the mt as a compound value. The write command disables or enables an automatic positive response (auto- answer) to the receipt of a reque...
Page 48
001-0004-829 rev00 page 48 of 84 at+cgreg gprs network registration status: the read command returns the status of result code presentation and an integer which shows whether the network has currently indicated the registration of the mt. The write command controls the presentation of an unsolicited...
Page 49
001-0004-829 rev00 page 49 of 84 atd request gprs or gprs ip service: this command causes the mt to perform whatever actions are necessary to establish a communication between the te and the external pdn. Request gprs service: atd*99***# l2p: blank – non ppp “ppp“ - layer 2 protocol ppp “1“ - layer ...
Page 50
001-0004-829 rev00 page 50 of 84 at^scmr read concatenated sms messages at^scms send concatenated sms messages at^scmw write concatenated sms messages to memory at^slms list sms memory storage at^smgl list sms messages from preferred store without setting status to rec read at^smgo set or query sms ...
Page 51
001-0004-829 rev00 page 51 of 84 hardware related commands the at commands described in this section are related to the modems's hardware interface. A brief description of hardware related commands are provided in table 6.14. For futher information, refer to the cinterion tc63i at command set docume...
Page 52
001-0004-829 rev00 page 52 of 84 factory default at command values table 10.15: at command factory defaults configuration commands atq =0 atv =1 atx =4 at\v =1 at+cfun =1 at+cmee =0 at+cscs ="gsm" at^sm20 =1, =1 status control commands at+cmer =0, =0, =0, =0, =0 at+cind =1 ats18 =0 serial interface ...
Page 53
001-0004-829 rev00 page 53 of 84 short message service (sms) commands at+cmgf =0 at+cnmi =0, =0, =0, =0, =1 at+csdh =0 at+csmp =17, =167, =0, =0 at+csms =0 at^smgo =0 at^ssconf =0 at^ssda =0 at^ssmss =0 sim related commands at^scks =0 at^sset =0 hardware related commands at^sctm =0 at^sspi =0, =0, =...
Page 54
001-0004-829 rev00 page 54 of 84 s s e e c c t t i i o o n n 1 1 1 1 - - s s p p e e c c i i f f i i c c a a t t i i o o n n s s product specifications are subject to change without notice. General specifications interface connectors: universal socket connectivity led indicators: power & dcd antenna...
Page 55
001-0004-829 rev00 page 55 of 84 data transmission specifications internet services tcp, udp, http, ftp, smtp, pop3 gprs data transmission gprs class 12 mobile station class b pbcch support coding scheme cs 1-4 csd data transmission up to 14.4 kbps v.110 non-transparent mode ussd support specificati...
Page 56
001-0004-829 rev00 page 56 of 84 mechanical specifications the following section describes in detail the exterior dimensions of the smc-gprs. All of the drawings below are the approximate actual size. The drawings may be used as layout reference, but it is advised that a physical comparison be made ...
Page 57
001-0004-829 rev00 page 57 of 84 s s e e c c t t i i o o n n 1 1 2 2 - - s s e e r r v v i i c c e e a a n n d d s s u u p p p p o o r r t t product warranty, rma and contact information calamp guarantees that every smc-gprs cellular modem will be free from physical defects in material and workmansh...
Page 58
001-0004-829 rev00 page 58 of 84 a a p p p p e e n n d d i i x x a a – – p p o o w w e e r r s s u u p p p p l l y y d d e e s s i i g g n n i i n n f f o o r r m m a a t t i i o o n n power supply issues because of its high current consumption during transmission, power supply design for the smc-gp...
Page 59
001-0004-829 rev00 page 59 of 84 power losses and voltage drops for gsm/gprs cell module the cell modules are specified to operate with specific voltage supplies. Voltage supplies may range from 3.2v to 4.5v as measured on the module’s power connector. To be on the safe side, it should be assumed th...
Page 60
001-0004-829 rev00 page 60 of 84 smc-gprs power supply considerations ideally, the external 5vdc supply should be able to provide the 1.4a current required by the smc- gprs modem when the tx bursts occur. When this is not a practical design alternative, a mix between a linear regulator and capacitor...
Page 61
001-0004-829 rev00 page 61 of 84 a a p p p p e e n n d d i i x x b b – – c c r r e e a a t t i i n n g g a a d d i i a a l l - - u u p p n n e e t t w w o o r r k k i i n n g g c c o o n n n n e e c c t t i i o o n n windows xp add standard windows modem.
Page 62
001-0004-829 rev00 page 62 of 84.
Page 63
001-0004-829 rev00 page 63 of 84.
Page 64
001-0004-829 rev00 page 64 of 84.
Page 65
001-0004-829 rev00 page 65 of 84 configuring the modem.
Page 66
001-0004-829 rev00 page 66 of 84 create a dial-up networking (dun) connection.
Page 67
001-0004-829 rev00 page 67 of 84.
Page 68
001-0004-829 rev00 page 68 of 84.
Page 69
001-0004-829 rev00 page 69 of 84.
Page 70
001-0004-829 rev00 page 70 of 84.
Page 71
001-0004-829 rev00 page 71 of 84.
Page 72
001-0004-829 rev00 page 72 of 84.
Page 73
001-0004-829 rev00 page 73 of 84 windows vista add standard windows modem go to the control panel and select phone and modem ....
Page 74
001-0004-829 rev00 page 74 of 84.
Page 75
001-0004-829 rev00 page 75 of 84 choose the com port to be connected to the modem..
Page 76
001-0004-829 rev00 page 76 of 84.
Page 77
001-0004-829 rev00 page 77 of 84 configuring the modem.
Page 78
001-0004-829 rev00 page 78 of 84 create a dial-up networking (dun) connection choose set up a connection or network..
Page 79
001-0004-829 rev00 page 79 of 84.
Page 80
001-0004-829 rev00 page 80 of 84 set the dial-up phone number as *99***1#, and add the username and password if required. Choose a connection name..
Page 81
001-0004-829 rev00 page 81 of 84.
Page 82
001-0004-829 rev00 page 82 of 84.
Page 83
001-0004-829 rev00 page 83 of 84.
Page 84
001-0004-829 rev00 page 84 of 84 a a p p p p e e n n d d i i x x c c – – w w a a r r r r a a n n t t y y s s t t a a t t e e m m e e n n t t calamp warrants to the original purchaser for use ("buyer") that data telemetry products manufactured by drl ("products") are free from defects in material and...