Assembly manual 1/10th formula 1 car.
3254 - 2-56 button head 40194 - hard anodized alum pivot ball 12772 - 4-40 thin hex nut 1430 - 4-40 x ½” flat head 1209 - washer *note - sometimes it is helpful to over-tighten the top clamp screws, then work the ball around by hand, and then loosen the screws so the ball floats around very free. Do...
1426 - 4-40 x 5/16” flat head 1430 - 4-40 x ½” flat head one-piece side links 13615 - red low- profile ball *note - before installing, inspect the side links and you will notice that the screw holes on one side of the link are larger than the holes on the other side. Before popping the links on the ...
3440 - motor plate 1574 - graphite x-brace 3 1424 - 4-40 x 1/4” flat head 3442 - left side pod plate bag 3 slider pod 33411 - slider bearing carrier 1574 1436 - 4-40 x 3/8” button head 13615 - red low- profile ball bag 4 tweak plate 1570 - tweak plate 1570 1435 - 4-40 x 7/16” button head 33411 3288 ...
4 bag 4 1434 - 4-40 x 1/4” button head 1565 - wtf-1 rear top plate 1565 top plate 1407 - anodized hex balls (4) 1384 - 2-56 steel ballstuds & cups for damper tubes (4) 1384 1407 1397 - 2-56 set- screw stud 1384 - 2-56 steel ballstud & plastic ball cup 32694 - short 4-40 plastic ball cup (on tree) 13...
5 1854 - top deck - gen-x10 se bag 6 top deck 1424 - 4-40 x 1/4” flat head 1434 - 4-40 x 1/4” button head 3373 - plastic battery position pieces 1537 - hex standoff - wtf-1 top deck 1854 1537 3378 3373 1407 1407 - anodized hex balls (4) 3378 - body posts w/ collars (1 in.) ** adding the damper tubes...
6 2.510” 1 - thread the spring adjuster nut onto the shock body as shown. *this needs to be installed first or you will not be able to get it on later after the lower end of the shock is assembled!* 2 - insert only 1 of the small o-rings into the lower end of the shock body. Next, install the bottom...
Front end lip bag f 33461 3221 7 1540 1546 1540 - front end plate - f1 1546 - f1 lower arm pivot ball 1434 - 4-40 x 1/4” button head 13615 - red low- profile ball 1412 - red locknut 3234 - brass set screw 3391 - .45mm front spring 3228 - crc king pin - long 1:10 3221 - steering block set 1535 - f1 s...
Front end - continued... 1.192” 1553 8 1544 1544 - f1 upper arm / steering block ball 3221 - steering block set 1582 - e-clip for upper hinge pin 13615 - red low- profile ball 1424 - 4-40 x 1/4” flat head 1436 - 4-40 x 3/8” button head 3221 bag f 1499 - m4 locknut 1496 - m4 x 30mm front end screw 14...
4201 - diff ring 1387 - 1/4” x 3/8” plain bearing lip 4121 - diff spacer 4123 - spring washer 1 - i nstall and grease the diff balls place the spur gear flat on the table in front of you with the side that says “crc” facing down. The diff balls will fall into each of the outer ring of holes in the d...
13783 - 4-40 x 1/8” set screw 10 1436 - 4-40 x 3/8” button head 1378 bag 10 bag 11 1378 - body posts w/ collars (2 in.) 3378 - body posts w/ collars (1 in.) 1 piece of 3378 will mount to the front wing (not included) once it is installed. 1499 - m4 locknut 1529 - 5mm plastic spacer - f1 fr axle 1532...
