CalderaSpas Aspire Owner's Manual - Operating Instructions
45
TEMPERATURE LOCK
The Temperature Lock feature deactivates the temperature control function from the control panel. All other functions on the control panel will
operate normally. Temperature Lock is most often used by those who do not want others to change the set temperature of the spa water.
To activate the Temperature Lock, press “SET” button + “TEMP
▲
“ button and hold for three seconds until lock symbol is illuminated.
To deactivate the Temperature Lock, press “SET” button + “TEMP
▲
“ button and hold for three seconds until the lock symbol is no longer illuminated.
MAIN CONTROL PANEL BUTTONS AND DISPLAY
Your spa control system consists of an illuminated Light Emitting Diode (LED) and convenient push buttons that allow you to set the water temperature, as well as the
hydrotherapy jets, mood lighting, and optional jets from the spa control panel.
DISPLAY INVERSION
You may invert the main, four-digit display for easier viewing from inside the spa. Press and hold the “SET” button for three seconds until the display is inverted. Press
and hold the “SET” button for three seconds a second time to invert the four-digit display back to it’s original position.
TEMPERATURE CONTROL
The set temperature range is from 27°C (80°F) to 42°C (104°F). The set temperature of the spa water will automatically be 39°C (102°F) the first time power is applied.
This is the setting programmed at the factory. After the spa has been set up and used, the last temperature value set by the user will be stored in memory. If power is
disconnected from the spa, it will automatically revert to the last set temperature when power is reapplied. (Temperatures of any setting may rise
slightly depending on the current use and condition of your spa, and on outside temperature.)
To display the set temperature of the spa, press the “TEMP
▲
“ or “TEMP
▼
“ button. The set temperature will be displayed, unless the spa is
locked (in which case the word SPA is displayed with the lock symbol). The set temperature display will automatically return to actual temperature
after five seconds.To increase the set temperature of the spa water, press the “TEMP
▲
“ button. Each time the button is pressed, the set
temperature display will increment by one degree. If the button is held down, the set temperature display will increase by one degree every half-second.
To decrease the set temperature of the spa water, press the “TEMP
▼
“ Each time the button is pressed, the set temperature display will decrement by one degree. If
the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the temperature control is disabled.
JETS BUTTONS
Your spa model uses one or two buttons which affect the jet pump(s):
The “JETS 1” (“JETS” for Kauai
®
) button activates jet pump 1. When the “JETS 1” button is pressed, the jets symbol will illuminate on the control
panel display. The symbol will remain lit until the button is pressed to turn off the jet pump 1, or after one hour of continuous operation when the
pump is automatically shut off by the control system.
The “JETS 2” button (used on Geneva
TM
, Niagara
®
, Tahitian
®
, Elation
®
, Aspire
®
, Moorea
®
, Hawaiian and Martinique
®
) activates jet pump 2. When the “JETS 2” button is
first pressed, the pump is in low speed (except Martinique which has a single speed pump) and the jets symbol illuminates on the control panel display. Pressing the
button a second time switches the jet pump to high speed mode. The symbol will remain lit until the button is pressed a third time turning jet pump 2 off, or after one
hour of continuous operation when the pump is automatically shut off by the control system.
MANUAL CLEAN CYCLE
The “CLEAN” button has been provided as a convenient timer for water maintenance. When the “CLEAN” button is pressed, Jet pump 1 will activate. The jet pump
symbol will flash on and off until the cleaning cycle is complete. The total cleaning cycle time is ten minutes. If the clean cycle does not engage, make sure the SPA
LOCK is deactivated. SPA LOCK disables the controls on both the main, and auxiliary control panels.
AIR JETS BUTTON
(Available on Geneva, Niagara, Tahitian, Moorea and Hawaiian spas)
The “AIR” button activates the air blower. When the “AIR” button is pressed, the air symbol will illuminate on the control panel display. The symbol will remain lit until the
button is pressed to turn off the air blower, or after fifteen minutes when the blower is automatically shut off by the control system. While the air blower is on, air-only jets
are operating throughout the spa. To stop the air blower when active, simply press the “AIR” button.
LIGHT CONTROL
The “LIGHT” button activates the light and controls the intensity of the light. Pressing the “LIGHT” button operates the light as follows:
• 1st press of the “LIGHT” button – light will turn on to the maximum intensity.
• 2nd press of the “LIGHT” button – light will turn to medium intensity.
• 3rd press of the “LIGHT” button – light will turn to low intensity.
• 4th press of the “LIGHT” button – light will turn off.
If the light is left on, it will automatically be turned off by the control system after six hours of continuous operation. The light symbol on the control panel will also turn
off when the light is deactivated.
If the light will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panel.
SPAGLO
®
COLOR WHEEL
Press the “SET” + “LIGHT” button simultaneously while the light is on to start or stop the SpaGlo color wheel. The light symbol will flash on and off while the SpaLux
color wheel is cycling through the six color options and the light symbol will display constant when the SpaGlo color wheel is stopped.