CalderaSpas vacanza series Owner's Manual - Palatino, Marino,
Page 24
7. Close the spa cover and fasten the cover tie downs. Cover the spa
cover with two pieces of plywood to evenly distribute the weight of
snow and ice. Secure a plastic sheet, or tarp, over the spa cover
and plywood.
8. Replace the equipment access door, if removed.
OPENING INSTRUCTIONS:
1. Remove plywood and plastic sheet. Open the spa cover by
unfastening the cover tie downs.
2. Follow the Start-up and Refill Procedures in the Operating
Instructions section of the Owner’s Manual. Do not install filters to
prevent them from exposure to the anti-freeze.
3. As part of this process, superchlorinate the spa water by adding
three teaspoons of chlorine (sodium dichlor) per 250 gallons of spa
water into the filter compartment. This is twice the normal amount
of chlorine needed for superclorination. This extra amount of
chlorine is needed to destroy the anti-freeze.
NOTE: A defoamer may be needed to decrease the amount of foam
caused by the anti-freeze.
4. Drain your spa to ensure removal of anti-freeze. Do not drain water
on grass or plants due to excessive chlorine level.
5. After the spa has completely drained, re-install your filter and follow
the Start-up and Refill Procedures in the Operating Instructions
section of the Owner’s Manual.
IMPORTANT: Always keep spa covered when not in use, whether it is
empty or full.
FILTER SYSTEM
The filter lid on the spa is NOT designed to support heavy weight loads
and should not be used as a seat. In extreme cases, the lid could crack
and break. This occurrence is considered abuse and is not covered
under the warranty.
CALDERA spas are equipped with one filter cartridge, sized to meet the
needs of the jet pump system.
At least once a week, check and clean the skimmer basket and weir to
ensure proper filter flow. Remove leaves, foreign matter, and debris. It is
very important to keep your spa filter cartridge clean and free of particles
to ensure proper water flow. A clean filter permits the hydrotherapy
system to function properly and also allows more efficient filter cycles.
Depending on how frequently your spa is used, we recommend cleaning
the spa filter cartridge every four weeks. If this is not done, the filter may
clog and restrict water flow, which causes improper filtration and poor jet
performance.
WARNING: To reduce the risk of injury to persons using the spa,
DO NOT remove the suction fittings (filter standpipes) located in the filter
compartment and do not sit on the filter lid, in extreme cases the lid
could crack and break. This occurrence is considered abuse and is not
covered under warranty.
FILTER CARTRIDGES REMOVAL &
CLEANING FOR
PALATINO, MARINO,
VANTO & TARINO MODELS.
1. Disconnect the spa from the power supply by turning the power to the
spa OFF.
2. Remove any floating items from within the filter compartment.
3. Turn the filter retainer handle (located on the top of the filter cartridge)
counterclockwise until the retainer can be removed from the filter
standpipe.
4. Remove the filter retainer, cover and cartridge (cover only used on
TEMPO, RELAY & RHYTHM spa models).
SERVICE NOTE: Never remove the filter standpipe when debris is present
in the filter compartment. Debris may find its way into the internal plumbing
which may result in blockage. NEVER REMOVE SUCTION FITTINGS!
5. Always clean the filter using a filter degreaser, such as
MONARCH Filter Cleaner, to remove mineral and oil build-up. Simply
soak the filter in the degreaser according to the package directions,
then place the filter on a clean surface and spray until clean using a
garden hose. It may be necessary to rotate the filter while spraying to
remove any debris lodged between the filter pleats.
6. To reinstall the filter cartridge, reverse the order of steps in which it
was removed. Do not overtighten.
WARNING: Do not use the spa with the filter cartridges, or filter
standpipe(s) removed!
FILTER
CARTRIDGE
STANDPIPE
RETAINER
HANDLE
FRESHWATER
Ag+
SILVER ION
PURIFIER INSIDE
STANDPIPE
FILTER
COVER
Spa Care and Maintenance