- DL manuals
- Cambium
- Network Router
- PTP 650
- User Manual
Cambium PTP 650 User Manual
Summary of PTP 650
Page 1
F cambium ptp 700 series user guide system release 700-01-00
Page 2
Accuracy while reasonable efforts have been made to assure the accuracy of this document, cambium networks assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. Cambium reserves the right to make changes to any products de...
Page 3: Contents
Contents about this user guide .......................................................................................................................... 1 contacting cambium networks .................................................................................................... 1 purpose ........
Page 4
Contents ofdm and channel bandwidth ................................................................................................ 1-10 spectrum management ............................................................................................................ 1-11 adaptive modulation ...........
Page 5
Contents chapter 2: system hardware .......................................................................................................... 2-1 outdoor unit (odu) ........................................................................................................................... 2-2 odu de...
Page 6
Contents nidu specifications ................................................................................................................... 2-52 chapter 3: system planning ........................................................................................................... 3-1 typical dep...
Page 7
Contents data network planning .................................................................................................................... 3-35 ethernet interfaces .................................................................................................................... 3-35 layer...
Page 8
Contents electrical safety compliance ..................................................................................................... 4-22 electromagnetic compatibility (emc) compliance ................................................................. 4-22 human exposure to radio frequency ene...
Page 9
Contents mounting the gps receiver ...................................................................................................... 5-30 preparing the gps drop cable .................................................................................................. 5-30 assembling an rj45 plug ...
Page 10
Contents lan configuration page ........................................................................................................... 6-34 qos configuration page ........................................................................................................... 6-44 sfp configuration p...
Page 11
Contents checking that the unit is in the fips 140-2 operational state .............................................. 6-106 aligning antennas .......................................................................................................................... 6-108 starting up the units ..........
Page 12
Contents sfp port counters page ............................................................................................................ 7-56 synce status page .................................................................................................................... 7-57 diagnostics pl...
Page 13: About This User Guide
About this user guide this guide describes the planning, installation, configuration and operation of the cambium ptp 700 series of point-to-point wireless ethernet bridges. It is intended for use by the system designer, system installer and system administrator. For radio network design, refer to t...
Page 14: Cross References
About this user guide important regulatory information cambium disclaims all liability whatsoever, implied or express, for any risk of damage, loss or reduction in system performance arising directly or indirectly out of the failure of the customer, or anyone acting on the customer's behalf, to abid...
Page 15: Radar Avoidance
About this user guide important regulatory information important regulatory information the ptp 700 product is certified as an unlicensed device in frequency bands where it is not allowed to cause interference to licensed services (called primary users of the bands). Radar avoidance in countries whe...
Page 16: Application Firmware
About this user guide important regulatory information other variants of the ptp 700 are available for use in the rest of the world, but these variants are not supplied to the usa or canada except under strict controls, when they are needed for export and deployment outside the usa or canada. Rensei...
Page 17: Avoidance Of Weather Radars
About this user guide important regulatory information avoidance of weather radars the installer must be familiar with the requirements in fcc kdb 443999. Essentially, the installer must be able to: • access the fcc data base of weather radar location and channel frequencies. • use this information ...
Page 18: Lightning Protection
About this user guide important regulatory information lightning protection to protect outdoor radio installations from the impact of lightning strikes, the installer must be familiar with the normal procedures for site selection, bonding and grounding. Installation guidelines for the ptp 700 can be...
Page 19: Problems And Warranty
About this user guide problems and warranty problems and warranty reporting problems if any problems are encountered when installing or operating this equipment, follow this procedure to investigate and report: 1 search this document and the software release notes of supported releases. 2 visit the ...
Page 20: Security Advice
About this user guide security advice security advice cambium networks systems and equipment provide security parameters that can be configured by the operator based on their particular operating environment. Cambium recommends setting and using these parameters following industry recognized securit...
Page 21: Warnings
About this user guide warnings, cautions, and notes warnings, cautions, and notes the following describes how warnings and cautions are used in this document and in all documents of the cambium networks document set. Warnings warnings precede instructions that contain potentially hazardous situation...
Page 22: Caring For The Environment
About this user guide caring for the environment caring for the environment the following information describes national or regional requirements for the disposal of cambium networks supplied equipment and for the approved disposal of surplus packaging. In eu countries the following information is p...
Page 23
Chapter 1: product description this chapter provides a high level description of products in the ptp 700 series. It describes in general terms the function of the product, the main product variants and the main hardware components. The following topics are described in this chapter: • overview of th...
Page 24: Purpose
Chapter 1: product description overview of the ptp 700 series overview of the ptp 700 series this section introduces the key features, typical uses, product variants and components of the ptp 700 series. Purpose cambium ptp 700 series bridge products are designed for ethernet bridging over point-to-...
Page 25: Frequency Bands
Chapter 1: product description overview of the ptp 700 series table 1 main characteristics of the ptp 700 series characteristic value topology ptp wireless link condition los, near los or non-los range up to 200 km duplexing tdd (symmetric and asymmetric) connectivity ethernet synchronous ethernet i...
Page 26: Typical Bridge Deployment
Chapter 1: product description overview of the ptp 700 series typical bridge deployment the ptp 700 is an “all outdoor” solution consisting of a wireless bridge between two sites. Each site installation consists of a ptp 700 connectorized outdoor unit (odu) or a ptp 700 connectorized+integrated odu,...
Page 27: Hardware Overview
Chapter 1: product description overview of the ptp 700 series hardware overview the main hardware components of the ptp 700 are as follows: • outdoor unit (odu): the odu is a self-contained transceiver unit that houses both radio and networking electronics. The ptp 700 odu is supplied in two configu...
Page 28: Wireless Operation
Chapter 1: product description wireless operation wireless operation this section describes how the ptp 700 wireless link is operated, including modulation modes, power control and security. Time division duplexing tdd cycle ptp 700 links operate using time division duplexing (tdd). They use a tdd c...
Page 29: Channel Selection
Chapter 1: product description wireless operation figure 2 tdd cycle channel selection the ptp 700 series links are capable of transmitting and receiving on the same channel or on different channels. In other words, the slave-master direction may use a different channel from the master-slave directi...
Page 30: Link Mode Optimization
Chapter 1: product description wireless operation link mode optimization link mode optimization allows the ptp 700 link to be optimized according to the type of traffic that will be bridged. The link supports two modes, ip traffic and tdm traffic. Ip traffic ip traffic mode is optimized to provide t...
Page 31: Further Reading
Chapter 1: product description wireless operation • 2:1 – the capacity in the direction master to slave is twice that of the direction slave to master. The ptp 700 series achieves this by setting the burst duration of the master to twice that of the slave. • 1:2 – the capacity in the direction slave...
Page 32: Further Reading
Chapter 1: product description wireless operation further reading for information about… refer to… link range capability upgrade capability upgrades on page 1-51 effect of link range on data throughput capacity calculating data rate capacity on page 3-27 data throughput capacity tables on page 3-71 ...
Page 33: Spectrum Management
Chapter 1: product description wireless operation spectrum management the spectrum management feature of the ptp 700 series monitors the available wireless spectrum and directs both ends of the wireless link to operate on a channel with a minimum level of co-channel and adjacent channel interference...
Page 34: Adaptive Modulation
Chapter 1: product description wireless operation adaptive modulation the ptp 700 series can transport data over the wireless link using a number of different modulation modes ranging from 256qam 0.81 to bpsk 0.63. For a given channel bandwidth and tdd frame structure, each modulation mode transport...
Page 35: Mimo
Chapter 1: product description wireless operation mimo multiple-input multiple-output (mimo) techniques provide protection against fading and increase the probability that the receiver will decode a usable signal. When the effects of mimo are combined with those of ofdm techniques and a high link bu...
Page 36: Further Reading
Chapter 1: product description wireless operation • second mode: the frequency of operation can be determined independently for each direction. This mode is not permitted in radar regions. Further reading for information about… refer to… using dso in ptp networks using dynamic spectrum optimization ...
Page 37: Encryption
Chapter 1: product description wireless operation for information about… refer to… planning for mandatory radar detection frequency selection on page 3-23 radar avoidance when aligning antennas odu installation tones on page 6-111 effect of radar detection on spectrum management spectrum expert page...
Page 38: Further Reading
Chapter 1: product description wireless operation the country of operation (and thus the supported regulatory bands) can be changed by generating a new license key at the license key generator page of the cambium web-site, and entering the new license key using the installation wizard. Caution to av...
Page 39: Synchronized Networks
Chapter 1: product description wireless operation the frequency planning task is made more straightforward by use of the following techniques: • using several different channels • separating units located on the same mast • using high performance (directional) external antennas synchronized networks...
Page 40: Configuring The Tdd Frame
Chapter 1: product description wireless operation timing references for use with ptp-sync ptp-sync requires an external timing reference in all but the simplest networks. Up to ten ptp-syncs can be connected in a chain to share the timing signal from one timing reference. In the majority of applicat...
Page 41
Chapter 1: product description wireless operation for information about… refer to… how to install a ptp-sync unit installing a ptp-sync unit on page 5-26 how to install an optional gps receiver installing a gps receiver on page 5-30 how to enable tdd synchronization wireless configuration page on pa...
Page 42: Ethernet Bridging
Chapter 1: product description ethernet bridging ethernet bridging this section describes how the ptp 700 processes ethernet data, and how ethernet ports are allocated to the data service, second data service, management service and local management service. Ethernet ports the ptp 700 series odu has...
Page 43: Second Data Service
Chapter 1: product description ethernet bridging second data service this optional point-to-point transparent service offers a second virtual circuit for customer’s data between one of the ethernet ports at the local odu and one of the ethernet ports at an associated remote odu. The data service and...
Page 44: Data Network
Chapter 1: product description ethernet bridging for information about… refer to… a more detailed description of the second data service second data service on page 1-21 a more detailed description of the out- of-band management service management service on page 1-21 sfp optical or copper module ki...
Page 45: Fragmentation
Chapter 1: product description ethernet bridging • multiple spanning tree protocol (mstp) • link aggregation control protocol (lacp) • link oam, ieee 802.3ah • port authentication, ieee 802.1x • ethernet local management interface (e-lmi), itu-t q.933. • link layer discovery protocol (lldp) • multip...
Page 46: Further Reading
Chapter 1: product description ethernet bridging data port wireless link down alert the ptp 700 series provides an optional indication of failure of the wireless link by means of a brief disconnection of the copper or optical data port allocated to the customer data network. The wireless link down a...
Page 47: Fragmentation
Chapter 1: product description ethernet bridging the service is transparent to untagged frames, standard vlan frames, priority-tagged frames, provider bridged frames, q-in-q frames and provider backbone bridged frames. In each case, the service preserves mac addresses, vlan id, ethernet priority and...
Page 48: Further Reading
Chapter 1: product description ethernet bridging lowest second data modulation mode the ptp 700 odu can be configured to discard ethernet frames in the second data service when the modulation mode is lower than the configured lowest second data modulation mode. This feature is likely to be useful in...
Page 49: Fragmentation
Chapter 1: product description ethernet bridging layer two control protocols the management service in the ptp 700 series is transparent to layer two control protocols (l2cp) including: • spanning tree protocol (stp), rapid spanning tree protocol (rstp) • multiple spanning tree protocol (mstp) • lin...
Page 50: Ethernet Loopback Mode
Chapter 1: product description ethernet bridging for information about… refer to… how to configure the ethernet service lan configuration page on page 6-34 how to configure ethernet quality of service qos configuration page on page 6-44 how to monitor ethernet performance system statistics on page 7...
Page 51: Protocol Model
Chapter 1: product description ethernet bridging protocol model ethernet bridging behavior at each end of the wireless link is equivalent to a two-port, managed, transparent mac bridge where the two ports are a wired ethernet port allocated to the data service, second data service, out-of-band manag...
Page 52: Further Reading
Chapter 1: product description ethernet bridging figure 4 protocol layers between external interfaces and the management agent management agent management, wireless, data ports media access method specific functions http/snmp/smtp tcp/ip mac relay entity further reading for information about… refer ...
Page 53: Further Reading
Chapter 1: product description ethernet bridging further reading for information about… refer to… relationship between synchronous ethernet and tdm tdm description on page 1-33 availability of synchronous ethernet capability upgrades on page 1-51 relationship between synchronous ethernet and etherne...
Page 54: Further Reading
Chapter 1: product description ethernet bridging further reading for information about… refer to… relationship between ieee 1588-2008 transparent clock and tdm tdm description on page 1-33 availability of ieee 1588-2008 transparent clock capability upgrades on page 1-51 relationship between ieee 158...
Page 55: Tdm Bridging
Chapter 1: product description tdm bridging tdm bridging this section describes how tdm traffic (e1 or t1) may be carried over ptp 700 links. If a nidu is installed at each link end, the ptp 700 link supports up to eight e1 channels or up to eight t1 channels. The link relays unstructured e1 or t1 d...
Page 56: Lowest Tdm Modulation Mode
Chapter 1: product description tdm bridging timing transfer for tdm circuits accurate timing transfer for tdm circuits in the ptp 700 series is based on the same underlying technology as the ieee 1588 transparent clock and synchronous ethernet features. Consequently, the ieee 588 and synchronous eth...
Page 57: Further Reading
Chapter 1: product description tdm bridging further reading for information about… refer to… the hardware required to implement tdm network indoor unit (nidu) on page 2-50 a typical e1 or t1 site deployment e1 or t1 interfaces on page 3-4 where to locate the nidu nidu location on page 3-17 tdm inter...
Page 58: System Management
Chapter 1: product description system management system management this section introduces the ptp 700 management system, including the web interface, installation, configuration, alerts and upgrades. Management agent ptp 700 equipment is managed through an embedded management agent. Management work...
Page 59: Network Management
Chapter 1: product description system management network management ipv4 and ipv6 interfaces the ptp 700 odu contains an embedded management agent with ipv4 and ipv6 interfaces. Network management communication is exclusively based on ip and associated higher layer transport and application protocol...
Page 60: Source Address Learning
Chapter 1: product description system management further examples of useful port allocation schemes are provided in chapter 3: system planning . Source address learning if local packet filtering is enabled, the ptp 700 learns the location of end stations from the source addresses in received managem...
Page 61: Ipv6
Chapter 1: product description system management ipv6 the ptp 700 management agent supports the following ipv6 features: neighbor discovery ptp 700 supports neighbor discovery for ipv6 as specified in rfc 4861 including: • neighbor un-reachability detection (nud), • sending and receiving of neighbor...
Page 62: Security
Chapter 1: product description system management multicast listener discovery for ipv6 the ptp 700 management agent supports multicast listener discovery version 1 (mldv1) as specified in rfc 2710. Ptp 700 does not support multicast listener discovery version 2 (mldv2). Textual representation of ipv...
Page 63: Transport Layer Security
Chapter 1: product description system management • installation: the installation wizard is used to install license keys, configure the ptp 700 wireless interface and to arm the unit ready for alignment. • management: these web-pages are used to configure the network management interfaces. • securit...
Page 64: Password Complexity
Chapter 1: product description system management when identity-based user accounts are enabled, a security officer can define from one to ten user accounts, each of which may have one of the three possible roles: • security officer. • system administrator. • read only. Identity-based user accounts a...
Page 65: Further Reading
Chapter 1: product description system management remote authentication can be used in addition to local authentication, or can be used as a replacement for local authentication. If remote and local authentications are used together, ptp 700 checks log in attempts against locally stored user credenti...
Page 66: Further Reading
Chapter 1: product description system management simple network time protocol (sntp) the clock supplies accurate date and time information to the system. It can be set to run with or without a connection to a network time server (sntp). It can be configured to display local time by setting the time ...
Page 67: Snmpv3 Security
Chapter 1: product description system management snmpv3 security snmp engine id ptp 700 supports four different formats for snmp engine id: • mac address • ipv4 address • configurable text string • ipv6 address snmpv3 security configuration is re-initialized when the snmp engine id is changed. User-...
Page 68
Chapter 1: product description system management the secure configuration should be configured in a controlled environment to prevent disclosure of the initial security keys necessarily sent as plaintext, or sent as encrypted data using a predictable key. The initial security information should not ...
Page 69: Further Reading
Chapter 1: product description system management • read only • system administrator read only and system administrator users are associated with fixed views allowing access to the whole of the mib, excluding the objects associated with snmpv3 security. System administrators have read/write access as...
Page 70: System Logging (Syslog)
Chapter 1: product description system management system logging (syslog) ptp 700 supports the standard syslog protocol to log important configuration changes, status changes and events. The protocol complies with rfc 3164. Ptp 700 creates syslog messages for configuration changes to any attribute th...
Page 71: Further Reading
Chapter 1: product description system management encryption must be configured with the same size key in each direction. Aes encryption at the ptp 700 wireless port is based on pre-shared keys. An identical key must be entered at each end of the link. Aes encryption for snmpv3 or tls is always based...
Page 72: Further Reading
Chapter 1: product description system management ptp 700 software images are digitally signed, and the odu will accept only images that contain a valid cambium networks digital signature. The odu always requires a reboot to complete a software upgrade. Note obtain the application software and this u...
Page 73: Capability Upgrades
Chapter 1: product description system management capability upgrades odus are shipped with a default license key factory-installed. The default license key enables a limited set of capabilities which depend upon the odu variant. Capability upgrades are purchased from cambium and supplied as access k...
Page 74: Recovery Mode
Chapter 1: product description system management recovery mode the ptp 700 recovery mode provides a means to recover from serious configuration errors including lost or forgotten passwords and unknown ip addresses. Recovery mode also allows new main application software to be loaded even when the in...
Page 75: Fips 140-2 Mode
Chapter 1: product description fips 140-2 mode fips 140-2 mode this section describes the (optional) fips 140-2 cryptographic mode of operation. Ptp 700 provides an optional secure cryptographic mode of operation validated to level 2 of federal information processing standards (fips) publication 140...
Page 76: Secure Mode Alarm
Chapter 1: product description fips 140-2 mode enforced configuration in fips approved mode when the ptp 700 odu operates in the fips approved mode, the following configuration settings are automatically enforced: • identity-based user accounts is enabled. • telnet management interface is disabled. ...
Page 77
Chapter 1: product description fips 140-2 mode • the http management interface must be disabled • aes encryption must be configured and enabled at the wireless interface. When the security configuration is completed correctly, the secure mode alarm is cleared from the system summary page and the sec...
Page 78: Further Reading
Chapter 1: product description fips 140-2 mode further reading for information about… refer to… cryptographic material needed for fips operation planning for fips 140-2 operation on page 3-58 installing license keys software license key page on page 6-11 loading software images software upgrade page...
Page 79
Chapter 2: system hardware this chapter describes the hardware components of a ptp 700 link. The following topics are described in this chapter: • outdoor unit (odu) on page 2-2 • power supply units (psu) on page 2-15 • antennas and antenna cabling on page 2-18 • ethernet cabling on page 2-32 • ptp-...
Page 80: Outdoor Unit (Odu)
Chapter 2: system hardware outdoor unit (odu) outdoor unit (odu) odu description one odu is required for each link end. The odu is a self-contained transceiver unit that houses both radio and networking electronics. Hardware platform variants ptp 700 odus are available in two different hardware plat...
Page 81: Atex/hazloc Variants
Chapter 2: system hardware outdoor unit (odu) the atex/hazloc odu variants are available only with the full capacity license. Atex/hazloc variants ptp 700 is available in atex/hazloc variants for operation in locations where explosive gas hazards exist, as defined by hazloc (usa) and atex (europe). ...
Page 82
Chapter 2: system hardware outdoor unit (odu) note to determine when to install external antennas and to calculate their impact on link performance and regulatory limits, see planning for connectorized units on page 3-29 . To select antennas, rf cables and connectors for connectorized units, see ant...
Page 83: Odu Kit Part Numbers
Chapter 2: system hardware outdoor unit (odu) cambium description cambium part number ptp 700 lite connectorized odu (fcc) c045070b007 ptp 700 lite connectorized odu (global) c045070b009 ptp 700 lite connectorized odu (eu) c045070b011 ptp 700 atex/hazloc connectorized odu (fcc) c045070b013 ptp 700 a...
Page 84
Chapter 2: system hardware outdoor unit (odu) figure 10 ptp 700 connectorized+integrated odu (front and rear views) page 2-6.
Page 85
Chapter 2: system hardware outdoor unit (odu) note to determine when to install external antennas and to calculate their impact on link performance and regulatory limits, see planning for connectorized units on page 3-29 . To select antennas, rf cables and connectors for connectorized units, see ant...
Page 86: Odu Kit Part Numbers
Chapter 2: system hardware outdoor unit (odu) cambium description cambium part number ptp 700 connectorized+integrated odu (global) c045070b004 ptp 700 connectorized+integrated odu (eu) c045070b006 ptp 700 lite connectorized+integrated odu (fcc) c045070b008 ptp 700 lite connectorized+integrated odu ...
Page 87: Odu Accessories
Chapter 2: system hardware outdoor unit (odu) cambium description (*1) part number ptp 700 precise network timing software license - per end c000070k003a ptp 700 group access software license - per end c000070k004a ptp 700 fips 140-2 upgrade including 128-bit aes - per end c000070k005a ptp 700 fips ...
Page 88
Chapter 2: system hardware outdoor unit (odu) figure 11 odu mounting bracket (integrated) figure 12 odu mounting bracket (connectorized) page 2-10
Page 89
Chapter 2: system hardware outdoor unit (odu) figure 13 odu extended integrated mounting bracket figure 14 odu large diameter extension kit table 8 odu mounting bracket part numbers bracket pole diameter odu variants bracket part number mounting bracket (integrated) 40 mm to 82 mm (1.6 inches to 3.2...
Page 90: Odu Interfaces
Chapter 2: system hardware outdoor unit (odu) bracket pole diameter odu variants bracket part number diameter extension kit inches) connectoized+integrated n000065l042 odu interfaces the psu, aux and sfp ports are on the rear of the odus ( figure 15 ). These interfaces are described in table 9 . Eac...
Page 91: Odu Specifications
Chapter 2: system hardware outdoor unit (odu) the front of the connectorized odu ( figure 16 ) provides n type female connectors for rf cable interfaces to antennas with horizontal (h) and vertical (v) polarization. Figure 16 connectorized odu antenna interfaces figure 17 connectorized+integrated od...
Page 92
Chapter 2: system hardware outdoor unit (odu) temperature -40°c (-40°f) to +60°c (140°f) wind loading 200 mph (323 kph) maximum. See odu wind loading on page 3-14 . Humidity 100% condensing liquid and particle ingress ip66, ip67 uv exposure 10 year operational life (ul746c test evidence) static disc...
Page 93: Power Supply Units (Psu)
Chapter 2: system hardware power supply units (psu) power supply units (psu) psu description the ac+dc power injector is an indoor unit that is connected to the odu and network terminating equipment using cat5e cable with rj45 connectors. It is also plugged into an ac or dc power supply so that it c...
Page 94: Psu Part Numbers
Chapter 2: system hardware power supply units (psu) psu part numbers order psus and (for ac power) line cords from cambium networks ( table 11 ). Table 11 power supply component part numbers cambium description cambium part number ptp 650/700 ac+dc enhanced power injector c000065l002 us line cord fi...
Page 95: Psu Specifications
Chapter 2: system hardware power supply units (psu) table 12 ac+dc enhanced power injector interface functions interface function 100-240v 47-63hz 1.5a ac power input (main supply). Dc in alternative dc power supply input. Dc out dc power output to a second psu (for power supply redundancy) or to a ...
Page 96: Antenna Requirements
Chapter 2: system hardware antennas and antenna cabling antennas and antenna cabling antenna requirements each connectorized odu requires one external antenna (normally dual-polar), or if spatial diversity is required, each odu requires two antennas. These antennas are not supplied by cambium networ...
Page 97
Chapter 2: system hardware antennas and antenna cabling • cable grounding kits: order one cable grounding kit for each grounding point on the antenna cables. Refer to lightning protection unit (lpu) and grounding kit on page 2-35 for specifications and part numbers. • self-amalgamating and pvc tape:...
Page 98
Chapter 2: system hardware antennas and antenna cabling • 5.4 ghz – 34.9 dbi par polarisation ou l'antenne. • 5.8 ghz – 37.7 dbi par polarisation ou l'antenne. Attention les antennes qui ne sont pas listées dans ces tableaux sont strictement interdites d’utilisation avec le ptp 700 dans les bandes s...
Page 99
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number radiowaves radio waves 3-foot parabolic, sp3-4.7 30.4 n000000d005 radiowaves radio waves 3-foot dual-pol parabolic, hpd3-4.7 30.2 rdh4517 gabriel gabriel 2.5-foot standard dual qu...
Page 100
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number radiowaves radio waves 90 sectorized (dual-pol), sec-47d-90-16 16.4 n000000d003 kppa omni (dual-pol) 13.0 radiowaves radio waves omni dual-pol, omnd-4.8-9 9.0 table 16 antennas pe...
Page 101
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number radiowaves radio waves 3-foot parabolic, sp3-5.2 31 rdh4513b gabriel gabriel 2.5-foot standard quickfire parabolic, qf2.5-52-n 30.8 gabriel gabriel 2.5-foot standard dual quickfir...
Page 102
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number andrew andrew 1-foot flat panel single, ubp300- 4-1 20.6 mars small form factor flat plate antenna part # ma-em56-dp19cm. 19 integrated laird 60 sectorized (dual-pol) 17 laird 90 ...
Page 103
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number stelladoradus stelladoradus 4-foot single-pol, 56 psd113 32.4 radiowaves radio waves 3-foot dual-pol parabolic, hpd3-5.2ns 32.3 rdh4509b radiowaves radio waves 3-foot parabolic, s...
Page 104
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number mti mti 15 inch dual-pol flat panel, mt- 485025/nvh 23 andrew andrew 1.25-foot flat panel dual, ubxp375-4-1 21 andrew andrew 1-foot flat panel single, ubp300- 4-1 21 mars small fo...
Page 105
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number andrew andrew 3-foot dual-pol parabolic, px3f-52 33.4 andrew andrew 3-foot parabolic, p3f-52 33.4 stelladoradus stelladoradus 4-foot single-pol, 56 psd113 32.4 radiowaves radio wa...
Page 106
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number stelladoradus stelladoradus 2-foot single-pol, 56 psd61 27 mars ma-ws54-50r flat plate (dual-pol) 23 integrated mti mti 15 inch dual-pol flat panel, mt- 485025/nvh 23 andrew andre...
Page 107
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number andrew andrew 4-foot dual-pol parabolic, px4f-52 34.9 rdg4453 andrew andrew 4-foot parabolic, p4f-52 34.9 rdh4524 gabriel gabriel 4-foot standard quickfire parabolic, qf4-52-n 34....
Page 108
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number andrew andrew 2-foot dual-pol parabolic, px2f-52 29.4 andrew andrew 2-foot parabolic, p2f-52 29.4 mti mti 3-foot single-pol, mt-487000/n 29 radiowaves radio waves 2-foot parabolic...
Page 109
Chapter 2: system hardware antennas and antenna cabling manufacturer antenna type nominal gain (dbi) cambium part number laird 90 sectorized (dual-pol) 17 kppa omni (dual-pol) 13 page 2-31.
Page 110: Ethernet Cabling
Chapter 2: system hardware ethernet cabling ethernet cabling ethernet standards and cable lengths all configurations require a copper ethernet connection from the odu (psu port) to the psu. Advanced configurations may also require one or both of the following: • a copper ethernet connection from the...
Page 111
Chapter 2: system hardware ethernet cabling table 21 aux and copper sfp ethernet standards and cable length restrictions odu drop cable power over ethernet ethernet supported (*1) maximum cable length (*2) aux – auxiliary device poe to auxiliary device 100base-tx 1000base-t 100 m (330 ft) none 100ba...
Page 112: Cable Grounding Kit
Chapter 2: system hardware ethernet cabling table 22 drop cable part numbers cambium description cambium part number 1000 ft reel outdoor copper clad cat5e wb3175 328 ft (100 m) reel outdoor copper clad cat5e wb3176 cable grounding kit copper drop cable shields must be bonded to the grounding system...
Page 113
Chapter 2: system hardware ethernet cabling lightning protection unit (lpu) and grounding kit ptp 700 lpus provide transient voltage surge suppression for ptp 700 installations. Each psu or aux drop cable requires two lpus, one near the odu and the other near the linked device, usually at the buildi...
Page 114: Lpu For Gps Drop Cables
Chapter 2: system hardware ethernet cabling one lpu and grounding kit ( table 24 ) is required for the psu drop cable connection to the odu. If the odu is to be connected to an auxiliary device, one additional lpu and grounding kit is required for the aux drop cable. Order the kits from cambium netw...
Page 115: Cable Hoisting Grip
Chapter 2: system hardware ethernet cabling lpu end kit ptp 250/300/500 wb2978 rj45 connectors and spare glands rj45 connectors are required for plugging cat5e cables into odus, lpus, psus and other devices. Order rj45 connectors and crimp tool from cambium networks ( table 27 ). Note the rj45 conne...
Page 116: Drop Cable Tester
Chapter 2: system hardware ethernet cabling figure 24 cable hoisting grip drop cable tester the drop cable tester is an optional item for testing the resistances between the rj45 pins of the drop cable ( figure 25 ). Order it by completing the order form on the support website (see contacting cambiu...
Page 117: Sfp Module Kits
Chapter 2: system hardware ethernet cabling sfp module kits sfp module kits allow connection of a ptp 700 series odu to a network over a gigabit ethernet interface in one of the following full-duplex modes: • optical gigabit ethernet: 1000base-lx or 1000base-sx • copper gigabit ethernet: 100base-tx ...
Page 118
Chapter 2: system hardware ethernet cabling the upgrade kits contain the following components: • optical or copper sfp transceiver module ( figure 26 ) • long emc strain relief cable gland ( figure 27 ) • the ptp 700 series sfp interface upgrade guide • license key instructions and unique access key...
Page 119
Chapter 2: system hardware ethernet cabling optical cable and connectors order an optical cable with lc connectors from a specialist fabricator, quoting the specification shown in figure 28 . It must be the correct length to connect the odu to the other device. Lc connectors should be supplied with ...
Page 120: Ptp-Sync Unit
Chapter 2: system hardware ptp-sync unit ptp-sync unit ptp-sync unit description the ptp-sync unit ( figure 29 ) is an optional component. It is required when tdd synchronization is implemented using ptp-sync. It measures the difference between the tdd frame timing and a 1 hz timing reference, and s...
Page 121: Ptp-Sync Part Numbers
Chapter 2: system hardware ptp-sync unit ptp-sync part numbers order ptp-sync kits and associated components from cambium networks ( table 31 ). Table 31 ptp-sync component part numbers cambium description cambium part number ptp-sync kit wb3665 ptp800 cmu / ptp-sync 19” rack mount installation kit ...
Page 122: Ptp-Sync Unit Interfaces
Chapter 2: system hardware ptp-sync unit ptp-sync unit interfaces the ptp-sync front panel is illustrated in figure 31. The annotated interfaces are described in table 32 and table 33 . Figure 31 ptp-sync front panel table 32 ptp-sync interface functions # description function 1 gps/sync in input fr...
Page 123: Ptp-Sync Specifications
Chapter 2: system hardware ptp-sync unit ptp-sync specifications the ptp-sync unit conforms to the specifications listed in table 34 , table 35 and table 36 . Table 34 ptp-sync unit physical specifications category specification dimensions width excluding ears 174 mm (6.69 in) width including ears 1...
Page 124
Chapter 2: system hardware ptp-sync unit there are two timing inputs to the ptp-sync unit: gps/sync in (rj-45) ( table 37 ) and 1pps in (sma) ( table 38 ). Table 37 ptp-sync unit timing specifications - gps/sync in (rj-45) category specification signal type differential 1 hz signal common mode range...
Page 125: Signal Polarities
Chapter 2: system hardware ptp-sync unit the pinouts of the ptp-sync unit gps/sync in port are specified in table 39 . Table 39 gps/sync in port pinouts pin no. Connector pinout signal name signal description pin 1 12vgps 12 v output to gps receiver module, 250 ma max pin 2 gnd ground pin 3 gps_1pps...
Page 126: Gps Receiver
Chapter 2: system hardware gps receiver gps receiver gps receiver description the gps receiver ( figure 32 ) is an optional timing reference source for ptp-sync. It provides a 1 hz signal, accurately synchronized in frequency and phase across the network. Figure 32 gps receiver the gps receiver is s...
Page 127: Gps Receiver Part Numbers
Chapter 2: system hardware gps receiver gps receiver part numbers order gps receivers and associated components from cambium networks ( table 40 ). Table 40 gps receiver component part numbers cambium description cambium part number trimble acutime™gg gps receiver wb4141 ptp-sync trimble adapter cab...
Page 128: Network Indoor Unit (Nidu)
Chapter 2: system hardware network indoor unit (nidu) network indoor unit (nidu) nidu description the nidu ( figure 34 ) is an optional component that adds up to eight tdm channels (e1 or t1) to a ptp 700 link. It multiplexes and demultiplexes e1, t1 and ethernet data over the wireless bridge. The n...
Page 129: Nidu Part Numbers
Chapter 2: system hardware network indoor unit (nidu) nidu part numbers order nidus and associated components from cambium networks ( table 42 ). Table 42 nidu component part numbers cambium description cambium part number network indoor unit (one per end) c000065l043 nidu - dc power connector spare...
Page 130: Nidu Specifications
Chapter 2: system hardware network indoor unit (nidu) nidu specifications the nidu conforms to the specifications listed in table 44 . Table 44 nidu specifications category specification dimensions width 172 mm (6.8 in) height 32 mm (1.3 in) depth 218 mm (8.6 in) weight 0.88 kg (1.95 lb) temperature...
Page 131
Chapter 2: system hardware network indoor unit (nidu) pin no. Connector pinout signal name (*) signal description pin 1 odu_phyn_pair1+ gigabit tx/rx pair 1 pin 2 odu_phyn_pair1- gigabit tx/rx pair 1 pin 3 odu_phyn_pair2+ gigabit tx/rx pair 2 pin 4 odu_phyn_pair3+ gigabit tx/rx pair 3 pin 5 odu_phyn...
Page 132
Chapter 3: system planning this chapter provides information to help the user to plan a ptp 700 link. The following topics are described in this chapter: • typical deployment on page 3-2 contains diagrams illustrating typical ptp 700 site deployments. • site planning on page 3-11 describes factors t...
Page 133: Typical Deployment
Chapter 3: system planning typical deployment typical deployment this section contains diagrams illustrating typical ptp 700 site deployments. Odu with poe interface to psu in the basic configuration, there is only one ethernet interface, a copper cat5e power over ethernet (poe) from the psu to the ...
Page 134
Chapter 3: system planning typical deployment figure 37 wall installation page 3-3.
Page 135: E1 Or T1 Interfaces
Chapter 3: system planning typical deployment figure 38 roof installation e1 or t1 interfaces there may be up to eight e1 or t1 channels connected to the odu via the psu port, as shown in figure 39 . The nidu is not compatible with the sfp or aux ports. Page 3-4.
Page 136
Chapter 3: system planning typical deployment figure 39 odu with e1 or t1 interfaces page 3-5.
Page 137
Chapter 3: system planning typical deployment sfp and aux ethernet interfaces there may be one or two additional ethernet interfaces connected to the odu: one to the sfp port (copper or optical) and one to the aux port, as shown in the following diagrams: • odu with copper sfp and psu interfaces – f...
Page 138
Chapter 3: system planning typical deployment page 3-7.
Page 139
Chapter 3: system planning typical deployment figure 42 odu with aux and psu interfaces page 3-8.
Page 140: Gps Receiver Interfaces
Chapter 3: system planning typical deployment gps receiver interfaces if a gps receiver is deployed for ptp-sync, it may be mounted on the wall of the equipment building ( figure 43 ) (preferred option), or on a metal tower or mast ( figure 44 ). Figure 43 gps receiver wall installation page 3-9.
Page 141
Chapter 3: system planning typical deployment figure 44 gps receiver tower or mast installation page 3-10
Page 142: Site Planning
Chapter 3: system planning site planning site planning this section describes factors to be considered when planning the proposed link end sites, including grounding, lightning protection and equipment location for the odu, psu and ptp- sync unit (if installed). Grounding and lightning protection wa...
Page 143: Site Grounding System
Chapter 3: system planning site planning figure 45 rolling sphere method to determine the lightning protection zones zone a: in this zone a direct lightning strike is possible. Do not mount equipment in this zone. Zone b: in this zone, direct emd (lightning) effects are still possible, but mounting ...
Page 144
Chapter 3: system planning site planning odu and external antenna location find a location for the odu (and external antenna for connectorized units) that meets the following requirements: • the equipment is high enough to achieve the best radio path. • people can be kept a safe distance away from t...
Page 145: Odu Wind Loading
Chapter 3: system planning site planning odu wind loading ensure that the odu and the structure on which it is mounted are capable of withstanding the prevalent wind speeds at a proposed ptp 700 site. Wind speed statistics should be available from national meteorological offices. The odu and its mou...
Page 146: Hazardous Locations
Chapter 3: system planning site planning hazardous locations check that the odus will not be exposed to hazardous gases, as defined by hazloc (usa) and atex (europe) regulations. If there is a risk of such exposure, then order the ptp 700 atex/hazloc product variants, as these are intended for opera...
Page 147: Psu Location
Chapter 3: system planning site planning psu location find a location for the ac+dc enhanced power injector that meets the following requirements: • the ac+dc enhanced power injector can be mounted on a wall or other flat surface. • the psu is kept dry, with no possibility of condensation, flooding ...
Page 148: Nidu Location
Chapter 3: system planning site planning mounting the gps receiver module on the equipment building if mounting the gps receiver for ptp-sync on the equipment building ( figure 43 ), select a position on the wall that meets the following requirements: • it must be below the roof height of the equipm...
Page 149: Lpu Location
Chapter 3: system planning site planning • if the tower is greater than 61 m (200 ft ) in height, the drop cable shield must be grounded at the tower midpoint, and at additional points as necessary to reduce the distance between ground cables to 61 m (200 ft) or less. • in high lightning-prone geogr...
Page 150
Chapter 3: system planning site planning figure 46 odu with psu, aux and copper sfp interfaces page 3-19.
Page 151
Chapter 3: system planning site planning figure 47 odu with psu, aux and optical sfp interfaces figure 48 bottom lpu and surge protector page 3-20
Page 152: Radio Spectrum Planning
Chapter 3: system planning radio spectrum planning radio spectrum planning this section describes how to plan ptp 700 links to conform to the regulatory restrictions that apply in the country of operation. Caution it is the responsibility of the user to ensure that the ptp product is operated in acc...
Page 153: Regulatory Limits
Chapter 3: system planning radio spectrum planning channel bandwidth (mhz) 5, 10, 15, 20, 30, 40, 45 5, 10, 15, 20 5, 10, 15, 20, 30, 40, 45 5, 10, 15, 20, 30, 40, 45 5, 10, 15, 20, 30, 40, 45 5, 10, 15, 20, 30, 40, 45 typical receiver noise 6.5 db 6.5 db 6.5 db 6.8 db 6.8 db 7.1 db typical antenna ...
Page 154: Available Spectrum
Chapter 3: system planning radio spectrum planning available spectrum the available spectrum for operation depends on the regulatory band. When configured with the appropriate license key, the unit will only allow operation on those channels which are permitted by the regulations. Certain regulation...
Page 155
Chapter 3: system planning radio spectrum planning regions with mandatory radar detection in regions that mandate dfs, the unit first ensures that there is no radar activity on a given channel for a period of 60 seconds before radiating on that channel. Once a channel has been selected for operation...
Page 156: Link Planning
Chapter 3: system planning link planning link planning this section describes factors to be taken into account when planning links, such as range, obstacles path loss and throughput. Linkplanner is recommended. Linkplanner the cambium linkplanner software and user guide may be downloaded from the su...
Page 157: Path Loss
Chapter 3: system planning link planning linkplanner for synchronized networks tdd synchronization should be planned using linkplanner. This will provide the necessary tdd frame parameter values which are required to complete a synchronized installation. Please refer to the linkplanner user guide. P...
Page 158: Calculation Procedure
Chapter 3: system planning link planning calculating data rate capacity the data rate capacity of a ptp link is defined as the maximum end-to-end ethernet throughput (including ethernet headers) that it can support. It is assumed that ethernet frames are 1518 octet. Data rate capacity is determined ...
Page 159: Calculation Example
Chapter 3: system planning link planning calculation example suppose that the link characteristics are: • ptp 700 variant = lite • link symmetry = 1:1 • link mode optimization = tdm • modulation mode = 64qam 0.92 dual • channel bandwidth = 10 mhz • link range = 60 km the calculation procedure for th...
Page 160: Choosing External Antennas
Chapter 3: system planning planning for connectorized units planning for connectorized units this section describes factors to be taken into account when planning to use connectorized odus with external antennas in ptp 700 links. When to install connectorized units the majority of radio links can be...
Page 161
Chapter 3: system planning planning for connectorized units note under industry canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by industry canada. To reduce potential radio interference to other users, ...
Page 162
Chapter 3: system planning configuration options for tdd synchronization configuration options for tdd synchronization this section describes the different configuration options that may be used for implementing tdd synchronization in the ptp 700 series. Schematic diagrams are included. The ptp 700 ...
Page 163
Chapter 3: system planning configuration options for tdd synchronization single link configuration with ptp-sync each link requires one ptp-sync unit connected to the master odu and one compatible gps receiver. Use this configuration where a site contains only one tdd master odu. The gps receiver an...
Page 164
Chapter 3: system planning configuration options for tdd synchronization cluster with ptp-sync and gps receiver each link requires one ptp-sync unit. Each site requires one compatible gps receiver. Collocated ptp-sync units are connected together in a daisy-chain. Between two and ten ptp- syncs may ...
Page 165
Chapter 3: system planning configuration options for tdd synchronization cluster with ptp-sync and no gps receiver each link requires one ptp-sync unit. Ptp-sync units are connected together in a daisy-chain. Between two and ten ptp-syncs may be chained in this way. One odu is designated as a cluste...
Page 166: Data Network Planning
Chapter 3: system planning data network planning data network planning this section describes factors to be considered when planning ptp 700 data networks. Ethernet interfaces the ptp 700 ethernet ports conform to the specifications listed in table 58 . Table 54 ptp 700 ethernet bridging specificati...
Page 167: Ethernet Port Allocation
Chapter 3: system planning data network planning ethernet port allocation port allocation rules decide how the three odu ethernet ports will be allocated to customer data service, second data service, management service and local management service based on the following rules: • map the data servic...
Page 168
Chapter 3: system planning data network planning figure 52 ports and services: data + local management figure 53 ports and services: data + local management + local management ptp 700 odu management agent wireless port ethernet port ethernet port ethernet port mac relay customer data local managemen...
Page 169
Chapter 3: system planning data network planning figure 54 ports and services: data + in-band management figure 55 ports and services: data + in-band management + local management ptp 700 odu management agent wireless port ethernet port ethernet port ethernet port mac relay customer data and in-band...
Page 170
Chapter 3: system planning data network planning figure 56 ports and services: data + in-band management + local management + local management figure 57 ports and services: data + out-of-band management ptp 700 odu management agent wireless port ethernet port ethernet port ethernet port mac relay cu...
Page 171
Chapter 3: system planning data network planning figure 58 ports and services: data + out-of-band management + local management figure 59 ports and services: data + second data + in-band management (with data) ptp 700 odu management agent ethernet port ethernet port ethernet port mac relay local man...
Page 172
Chapter 3: system planning data network planning figure 60 ports and services: data + second data + in-band management (with data) + local management figure 61 ports and services: data + second data + in-band management (with second data) ptp 700 odu management agent ethernet port ethernet port ethe...
Page 173
Chapter 3: system planning data network planning figure 62 ports and services: data + second data + in-band management (with second data) + local management figure 63 ports and services: data + second data + local management use a compatible combination of services at both ends of the link ptp 700 a...
Page 174
Chapter 3: system planning data network planning data + in-band management + [local management] + [local management] data + out-of-band management + [local management] data + second data + in-band management (with data) + [local management] data + second data + in-band management (with second data) ...
Page 175
Chapter 3: system planning data network planning figure 64 example of independent mapping of services to ports additional port allocation rules the three ethernet ports are generally interchangeable, except for some specific additional rules listed below: • if the tdm interface (e1 or t1) is enabled...
Page 176: Vlan Membership
Chapter 3: system planning data network planning vlan membership decide if the ip interface of the odu management agent will be connected in a vlan. If so, decide if this is a standard (ieee 802.1q) vlan or provider bridged (ieee 802.1ad) vlan, and select the vlan id for this vlan. Use of a separate...
Page 177: Layer 2 Control Protocols
Chapter 3: system planning data network planning ptp 700 provides eight queues for traffic waiting for transmission over the wireless link. Q0 is the lowest priority queue and q7 is the highest priority queue. Traffic is scheduled using strict priority; in other words, traffic in a given queue is tr...
Page 178: Green Ethernet Switches
Chapter 3: system planning data network planning “daisy-chaining” ptp 700 links when connecting two or more ptp 700 links together in a network (daisy-chaining), do not install direct copper cat5e connections between the psus. Each psu must be connected to the network terminating equipment using the...
Page 179: Tdm Network Planning
Chapter 3: system planning tdm network planning tdm network planning this section describes factors to be considered when planning ptp 700 tdm networks. Caution if the odu port has negotiated a link at 100base-t, the nidu will not send or receive tdm data, and will not bridge customer data traffic. ...
Page 180: Network Management Planning
Chapter 3: system planning network management planning network management planning this section describes how to plan for ptp 700 links to be managed remotely using snmp. Planning for snmp operation the supported notifications are as follows: • cold start • wireless link up/down • channel change • d...
Page 181: Enabling Snmp
Chapter 3: system planning network management planning enabling snmp enable the snmp interface for use by configuring the following attributes in the snmp configuration page: • snmp state (default disabled) • snmp version (default snmpv1/2c) • snmp port number (default 161) page 3-50
Page 182: Security Planning
Chapter 3: system planning security planning security planning this section describes how to plan for ptp 700 links to operate in secure mode. Planning for sntp operation note ptp 700 does not have a battery-powered clock, so the set time is lost each time the odu is powered down. To avoid the need ...
Page 183: Snmp Security Mode
Chapter 3: system planning security planning item description quantity required tls private key and public certificates an rsa private key of size 2048 bits, generated in either pkcs#1 or pkcs#5 format, unencrypted, and encoded in the asn.1 der format. An x.509 certificate containing an rsa public k...
Page 184
Chapter 3: system planning security planning web-based security management allows an operator to configure users, security levels, privacy and authentication protocols, and passphrases using the ptp 700 web-based management interface. The capabilities supported are somewhat less flexible than those ...
Page 186
Chapter 3: system planning security planning snmpv3 default configuration (mib-based) when snmpv3 mib-based security mode is enabled, the default configuration for the usmusertable table is based on one initial user and four template users as listed in table 61 . Table 61 default snmpv3 users object...
Page 187: Vacm Default Configuration
Chapter 3: system planning security planning vacm default configuration the default user initial is assigned to vacm group initial in the vacmsecuritytogrouptable table. The template users are not assigned to a group. Ptp 700 creates default view trees and access as shown in table 62 and table 63 . ...
Page 188: Radius Attributes
Chapter 3: system planning security planning planning for radius operation configure radius where remote authentication is required for users of the web-based interface. Remote authentication has the following advantages: • control of passwords can be centralized. • management of user accounts can b...
Page 189
Chapter 3: system planning security planning • login(1): read only • administrative(6): system administrator • nas prompt(7): read only if the auth-role and service-type attributes are absent, ptp 700 selects the read only role. The auth-role vendor-specific attribute is defined in table 64 . Table ...
Page 190: Further Reading
Chapter 3: system planning security planning • radius authentication disabled. Caution configure all of the above correctly to ensure that ptp 600 is operating in compliance with the fips 140-2 validation. Further reading for information about… refer to… generating security material for the https/tl...
Page 191
Chapter 3: system planning system threshold, output power and link loss system threshold, output power and link loss use the following tables to look up the system threshold (dbm), output power (dbm) and maximum link loss (db) per channel bandwidth and modulation mode: band mode system threshold and...
Page 192
Chapter 3: system planning system threshold, output power and link loss table 65 4.5 ghz ip mode: system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz p (all bands) bpsk 0.63 single -96.6 -95.1 -93.3 -92.0 29 qpsk 0.63 single -93.5 -92.0 -90.2 ...
Page 193
Chapter 3: system planning system threshold, output power and link loss table 67 4.5 ghz tdm mode:system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz p (all bands) bpsk 0.63 single -96.6 -95.1 -93.3 -92.0 29 qpsk 0.63 single -90.4 -88.9 -87.2 ...
Page 194
Chapter 3: system planning system threshold, output power and link loss table 69 4.9 ghz ip mode: system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz p (all bands) bpsk 0.63 single -96.6 -95.1 -93.3 -92.0 29 qpsk 0.63 single -93.5 -92.0 -90.2 ...
Page 195
Chapter 3: system planning system threshold, output power and link loss table 71 4.9 ghz tdm mode:system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz p (all bands) bpsk 0.63 single -96.6 -95.1 -93.3 -92.0 29 qpsk 0.63 single -90.4 -88.9 -87.2 ...
Page 196
Chapter 3: system planning system threshold, output power and link loss table 73 5.1/5.2 ghz ip mode: system threshold per channel bandwidth and o/p power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -95.8 -94.3 -92.5 -91.3 -89.5 -88.3 -87....
Page 197
Chapter 3: system planning system threshold, output power and link loss table 75 5.1/5.2 ghz tdm mode: system threshold per channel bandwidth and o/p pwr (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -95.8 -94.3 -92.5 -91.3 -89.5 -88.3 -87.8...
Page 198
Chapter 3: system planning system threshold, output power and link loss table 77 5.4 ghz ip mode: system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -96.6 -94.6 -92.8 -91.5 -89.8 -88.5 -88.0...
Page 199
Chapter 3: system planning system threshold, output power and link loss table 79 5.4 ghz tdm mode: system threshold per channel bandwidth and output power (p)(dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -96.6 -94.6 -92.8 -91.5 -89.8 -88.5 -88.0...
Page 200
Chapter 3: system planning system threshold, output power and link loss table 81 5.8 ghz ip mode: system threshold per channel bandwidth and output power (p) (dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -96.8 -94.8 -93.0 -91.8 -90.0 -88.8 -88.3...
Page 201
Chapter 3: system planning system threshold, output power and link loss table 83 5.8 ghz tdm mode: system threshold per channel bandwidth and output power (p)(dbm) modulation mode 5 mhz 10 mhz 15 mhz 20 mhz 30 mhz 40 mhz 45 mhz p (all bands) bpsk 0.63 single -96.8 -94.8 -93.0 -91.8 -90.0 -88.8 -88.3...
Page 202
Chapter 3: system planning data throughput capacity tables data throughput capacity tables use the following tables to look up the data throughput rates (mbits/s) that are achieved when two ptp 700 odus are linked and the link distance (range) is 0 km: ptp 700 variant link symmetry link optimization...
Page 203
Chapter 3: system planning data throughput capacity tables symmetry optimization 15 mhz 10 mhz 5 mhz 1:1 ip figure 69 figure 70 figure 71 tdm figure 76 figure 77 figure 78 2:1 ip figure 83 figure 84 - tdm figure 89 figure 90 - 3:1 ip figure 95 figure 96 - 5:1 ip - - - adaptive ip figure 104 figure 1...
Page 204
Chapter 3: system planning data throughput capacity tables table 85 throughput at zero link range (mbit/s), full, symmetry 1:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 226.1 226.1 452.2 206.3 206.3 412.6 64qam 0.92 dual 190.5 190.5 381.0 173...
Page 205
Chapter 3: system planning data throughput capacity tables 64qam 0.75 dual 51.9 51.9 103.8 34.5 34.5 69.0 16qam 0.87 dual 40.4 40.4 80.7 26.8 26.8 53.7 16qam 0.63 dual 29.0 29.0 58.0 19.3 19.3 38.6 256qam 0.81 single 37.7 37.7 75.4 25.0 25.0 50.1 64qam 0.92 single 31.7 31.7 63.5 21.1 21.1 42.2 64qam...
Page 206
Chapter 3: system planning data throughput capacity tables 16qam 0.63 dual 77.8 77.8 155.6 71.6 71.6 143.3 256qam 0.81 single 101.0 101.0 202.1 93.0 93.0 186.1 64qam 0.92 single 85.1 85.1 170.2 78.4 78.4 156.8 64qam 0.75 single 69.6 69.6 139.1 64.0 64.0 128.1 16qam 0.87 single 54.1 54.1 108.2 49.8 4...
Page 207
Chapter 3: system planning data throughput capacity tables 16qam 0.87 single 19.5 19.5 39.0 13.2 13.2 26.3 16qam 0.63 single 14.0 14.0 28.1 9.5 9.5 18.9 qpsk 0.87 single 9.8 9.8 19.5 6.6 6.6 13.1 qpsk 0.63 single 7.0 7.0 14.0 4.7 4.7 9.5 bpsk 0.63 single 3.5 3.5 7.0 2.4 2.4 4.7 modulation mode 5 mhz...
Page 208
Chapter 3: system planning data throughput capacity tables qpsk 0.87 single 40.1 20.1 60.2 36.6 18.3 55.0 qpsk 0.63 single 28.9 14.4 43.3 26.3 13.2 39.5 bpsk 0.63 single 14.4 7.2 21.6 13.2 6.6 19.7 modulation mode 30 mhz (tx/rx/aggregate) 20 mhz (tx/rx/aggregate) 256qam 0.81 dual 200.5 100.2 300.7 1...
Page 209
Chapter 3: system planning data throughput capacity tables page 3-78.
Page 210
Chapter 3: system planning data throughput capacity tables table 88 throughput at zero link range (mbit/s), full, symmetry 2:1, optimization tdm modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 280.8 140.4 421.2 257.7 128.9 386.6 64qam 0.92 dual 236.6 118.3 354.8 21...
Page 211
Chapter 3: system planning data throughput capacity tables 64qam 0.92 dual 83.2 41.6 124.9 55.9 27.9 83.8 64qam 0.75 dual 68.0 34.0 102.0 45.7 22.8 68.5 16qam 0.87 dual 52.9 26.5 79.4 35.5 17.8 53.3 16qam 0.63 dual 38.0 19.0 57.1 25.5 12.8 38.3 256qam 0.81 single 49.4 24.7 74.1 33.2 16.6 49.8 64qam ...
Page 212
Chapter 3: system planning data throughput capacity tables 16qam 0.87 dual 120.52 40.17 160.70 79.54 26.51 106.05 16qam 0.63 dual 86.64 28.88 115.52 57.18 19.06 76.24 256qam 0.81 single 112.51 37.50 150.01 74.25 24.75 98.99 64qam 0.92 single 94.79 31.60 126.38 62.56 20.85 83.41 64qam 0.75 single 77....
Page 213
Chapter 3: system planning data throughput capacity tables table 90 throughput at zero link range (mbit/s), full, symmetry 5:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 374.68 74.93 449.62 335.20 67.04 402.24 64qam 0.92 dual 315.68 63.13 378....
Page 214
Chapter 3: system planning data throughput capacity tables 64qam 0.92 dual 343.7 34.4 378.0 310.0 34.4 344.4 64qam 0.75 dual 280.8 28.1 308.9 253.3 28.1 281.4 16qam 0.87 dual 218.5 21.8 240.3 197.1 21.9 218.9 16qam 0.63 dual 157.1 15.7 172.8 141.7 15.7 157.4 256qam 0.81 single 204.0 20.4 224.3 183.9...
Page 215
Chapter 3: system planning data throughput capacity tables 256qam 0.81 single 60.1 15.0 75.1 33.2 16.6 49.8 64qam 0.92 single 50.6 12.7 63.3 27.9 14.0 41.9 64qam 0.75 single 41.4 10.3 51.7 22.8 11.4 34.3 16qam 0.87 single 32.2 8.0 40.2 17.8 8.9 26.6 16qam 0.63 single 23.1 5.8 28.9 12.8 6.4 19.2 qpsk...
Page 216
Chapter 3: system planning data throughput capacity tables table 92 throughput at zero link range (mbit/s), lite, symmetry 1:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 113.0 113.0 226.0 103.0 103.0 206.0 64qam 0.92 dual 95.0 95.0 190.0 87.0 ...
Page 217
Chapter 3: system planning data throughput capacity tables 64qam 0.75 dual 26.0 26.0 52.0 17.0 17.0 34.0 16qam 0.87 dual 20.0 20.0 40.0 13.0 13.0 26.0 16qam 0.63 dual 15.0 15.0 30.0 10.0 10.0 20.0 256qam 0.81 single 19.0 19.0 38.0 13.0 13.0 26.0 64qam 0.92 single 16.0 16.0 32.0 11.0 11.0 22.0 64qam ...
Page 218
Chapter 3: system planning data throughput capacity tables table 93 throughput at zero link range (mbit/s), lite, symmetry 1:1, optimization tdm modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 100.0 100.0 200.0 93.0 93.0 186.0 64qam 0.92 dual 84.0 84.0 168.0 78.0 7...
Page 219
Chapter 3: system planning data throughput capacity tables 64qam 0.75 dual 25.0 25.0 50.0 17.0 17.0 34.0 16qam 0.87 dual 20.0 20.0 40.0 13.0 13.0 26.0 16qam 0.63 dual 14.0 14.0 28.0 9.0 9.0 18.0 256qam 0.81 single 18.0 18.0 36.0 12.0 12.0 24.0 64qam 0.92 single 15.0 15.0 30.0 10.0 10.0 20.0 64qam 0....
Page 220
Chapter 3: system planning data throughput capacity tables table 94 throughput at zero link range (mbit/s), lite, symmetry 2:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 150.0 75.0 225.0 137.0 68.0 205.0 64qam 0.92 dual 126.0 63.0 189.0 115.0 ...
Page 221
Chapter 3: system planning data throughput capacity tables 64qam 0.75 dual 35.0 17.0 52.0 23.0 11.0 34.0 16qam 0.87 dual 27.0 13.0 40.0 18.0 9.0 27.0 16qam 0.63 dual 19.0 10.0 29.0 13.0 6.0 19.0 256qam 0.81 single 25.0 13.0 38.0 17.0 8.0 25.0 64qam 0.92 single 21.0 11.0 32.0 14.0 7.0 21.0 64qam 0.75...
Page 222
Chapter 3: system planning data throughput capacity tables table 95 throughput at zero link range (mbit/s), lite, symmetry 2:1, optimization tdm modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 139.0 70.0 209.0 129.0 64.0 193.0 64qam 0.92 dual 117.0 59.0 176.0 109.0...
Page 223
Chapter 3: system planning data throughput capacity tables 64qam 0.75 dual 34.0 17.0 51.0 23.0 11.0 34.0 16qam 0.87 dual 26.0 13.0 39.0 18.0 9.0 27.0 16qam 0.63 dual 19.0 10.0 29.0 13.0 6.0 19.0 256qam 0.81 single 25.0 12.0 37.0 17.0 8.0 25.0 64qam 0.92 single 21.0 10.0 31.0 14.0 7.0 21.0 64qam 0.75...
Page 224
Chapter 3: system planning data throughput capacity tables table 96 throughput at zero link range (mbit/s), lite, symmetry 3:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 169.0 56.0 225.0 154.0 51.0 205.0 64qam 0.92 dual 142.0 47.0 189.0 130.0 ...
Page 225
Chapter 3: system planning data throughput capacity tables 64qam 0.92 dual 47.0 16.0 63.0 32.0 11.0 43.0 64qam 0.75 dual 39.0 13.0 52.0 26.0 9.0 35.0 16qam 0.87 dual 30.0 10.0 40.0 20.0 7.0 27.0 16qam 0.63 dual 22.0 7.0 29.0 14.0 5.0 19.0 256qam 0.81 single 28.0 9.0 37.0 19.0 6.0 25.0 64qam 0.92 sin...
Page 226
Chapter 3: system planning data throughput capacity tables table 97 throughput at zero link range (mbit/s), lite, symmetry 5:1, optimization ip modulation mode 45 mhz (tx/rx/aggregate) 40 mhz (tx/rx/aggregate) 256qam 0.81 dual 187.0 37.0 224.0 168.0 34.0 202.0 64qam 0.92 dual 158.0 32.0 190.0 141.0 ...
Page 227
Chapter 3: system planning data throughput capacity tables figure 65 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 45 mhz figure 66 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 40 mhz 0.86 0.88 0.90 0.92 0.94 0.96 0.98 1.00 0 20 40 60 80 100 120 140...
Page 228
Chapter 3: system planning data throughput capacity tables figure 67 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 30 mhz figure 68 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 20 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 2...
Page 229
Chapter 3: system planning data throughput capacity tables figure 69 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 15 mhz figure 70 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 10 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 2...
Page 230
Chapter 3: system planning data throughput capacity tables figure 71 range adjustment for ptp 700, symmetry 1:1, optimization ip, bandwidth 5 mhz figure 72 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 45 mhz 0.60 0.70 0.80 0.90 1.00 0 20 40 60 80 100 120 140 160 180 200 r ...
Page 231
Chapter 3: system planning data throughput capacity tables figure 73 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 40 mhz figure 74 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 30 mhz 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 16...
Page 232
Chapter 3: system planning data throughput capacity tables figure 75 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 20 mhz figure 76 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 15 mhz 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 16...
Page 233
Chapter 3: system planning data throughput capacity tables figure 77 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 10 mhz figure 78 range adjustment for ptp 700, symmetry 1:1, optimization tdm, bandwidth 5 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 ...
Page 234
Chapter 3: system planning data throughput capacity tables figure 79 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 45 mhz figure 80 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 40 mhz 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 200 r ...
Page 235
Chapter 3: system planning data throughput capacity tables figure 81 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 30 mhz figure 82 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 20 mhz 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 ...
Page 236
Chapter 3: system planning data throughput capacity tables figure 83 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 15 mhz figure 84 range adjustment for ptp 700, symmetry 2:1, optimization ip, bandwidth 10 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 2...
Page 237
Chapter 3: system planning data throughput capacity tables figure 85 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 45 mhz figure 86 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 40 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 1...
Page 238
Chapter 3: system planning data throughput capacity tables figure 87 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 30 mhz figure 88 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 20 mhz 0.60 0.70 0.80 0.90 1.00 0 20 40 60 80 100 120 140 160 180 200 ...
Page 239
Chapter 3: system planning data throughput capacity tables figure 89 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 15 mhz figure 90 range adjustment for ptp 700, symmetry 2:1, optimization tdm, bandwidth 10 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180...
Page 240
Chapter 3: system planning data throughput capacity tables figure 91 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 45 mhz figure 92 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 40 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140...
Page 241
Chapter 3: system planning data throughput capacity tables figure 93 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 30 mhz figure 94 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 20 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140...
Page 242
Chapter 3: system planning data throughput capacity tables figure 95 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 15 mhz figure 96 range adjustment for ptp 700, symmetry 3:1, optimization ip, bandwidth 10 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140...
Page 243
Chapter 3: system planning data throughput capacity tables figure 97 range adjustment for ptp 700, symmetry 5:1, optimization ip, bandwidth 45 mhz figure 98 range adjustment for ptp 700, symmetry 5:1, optimization ip, bandwidth 40 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140...
Page 244
Chapter 3: system planning data throughput capacity tables figure 99 range adjustment for ptp 700, symmetry 5:1, optimization ip, bandwidth 30 mhz figure 100 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 45 mhz 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 1...
Page 245
Chapter 3: system planning data throughput capacity tables figure 101 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 40 mhz figure 102 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 30 mhz 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 180 200 r a...
Page 246
Chapter 3: system planning data throughput capacity tables figure 103 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 20 mhz figure 104 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 15 mhz 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 0 20 40 60 80 100 120 140 160 1...
Page 247: Tdm Traffic Load
Chapter 3: system planning data throughput capacity tables figure 105 range adjustment for ptp 700, adaptive, optimization ip, bandwidth 10 mhz tdm traffic load encapsulated data the nidu supports separate management and tdm data protocol interfaces. The management interface is between the nidu and ...
Page 248: Timing Only
Chapter 3: system planning data throughput capacity tables in the best case (eight channels) the encapsulation has an efficiency of 91.6%. Timing only the resulting tdm traffic load in timing-only operation is shown in table 99 . Table 99 tdm traffic load in timing-only channels octets per ethernet ...
Page 249
Chapter 4: legal and regulatory information this chapter provides end user license agreements and regulatory notifications. Caution intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any su...
Page 250: Definitions
Chapter 4: legal and regulatory information cambium networks end user license agreement cambium networks end user license agreement definitions in this agreement, the word “software” refers to the set of instructions for computers, in executable form and in any media, (which may include diskette, cd...
Page 251: Conditions Of Use
Chapter 4: legal and regulatory information cambium networks end user license agreement conditions of use any use of the software and documentation outside of the conditions set forth in this agreement is strictly prohibited and will be deemed a breach of this agreement. 1. Only you, your employees ...
Page 252: Title and Restrictions
Chapter 4: legal and regulatory information cambium networks end user license agreement title and restrictions if you transfer possession of any copy of the software and documentation to another party outside of the terms of this agreement, your license is automatically terminated. Title and copyrig...
Page 253: Transfer
Chapter 4: legal and regulatory information cambium networks end user license agreement right to use cambium’s name except as required in “conditions of use”, you will not, during the term of this agreement or thereafter, use any trademark of cambium networks, or any word or symbol likely to be conf...
Page 254: Disclaimer
Chapter 4: legal and regulatory information cambium networks end user license agreement disclaimer cambium networks disclaims all warranties of any kind, whether express, implied, statutory, or in any communication with you. Cambium networks specifically disclaims any warranty including the implied ...
Page 255: Term Of License
Chapter 4: legal and regulatory information cambium networks end user license agreement term of license your right to use the software will continue in perpetuity unless terminated as follows. Your right to use the software will terminate immediately without notice upon a breach of this agreement by...
Page 256: Trademarks
Chapter 4: legal and regulatory information cambium networks end user license agreement trademarks java technology and/or j2me : java and all other java-based marks are trademarks or registered trademarks of sun microsystems, inc. In the u.S. And other countries. Unix : unix is a registered trade...
Page 257
Chapter 4: legal and regulatory information cambium networks end user license agreement this software is provided by the copyright holders and contributors “as is” and any express or implied warranties, including, but not limited to, the implied warranties of merchantability and fitness for a partic...
Page 258
Chapter 4: legal and regulatory information cambium networks end user license agreement • redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. • neith...
Page 259: Openssl
Chapter 4: legal and regulatory information cambium networks end user license agreement • redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. • redistributions in binary form must reproduce the above copyright notice, this list...
Page 260
Chapter 4: legal and regulatory information cambium networks end user license agreement redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright not...
Page 261: Zlib
Chapter 4: legal and regulatory information cambium networks end user license agreement if this package is used in a product, eric young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (on...
Page 262: Libpng
Chapter 4: legal and regulatory information cambium networks end user license agreement mark adler madler@alumni.Caltech.Edu libpng libpng versions 1.2.6, august 15, 2004, through 1.2.35, february 14, 2009, are copyright © 2004, 2006-2008 glenn randers-pehrson, and are distributed according to the s...
Page 263: Bzip2
Chapter 4: legal and regulatory information cambium networks end user license agreement tim wegner the png reference library is supplied “as is”. The contributing authors and group 42, inc. Disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantabilit...
Page 264: Usb Library Functions
Chapter 4: legal and regulatory information cambium networks end user license agreement this software is provided by the author “as is” and any express or implied warranties, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are disclaimed....
Page 265: Apache
Chapter 4: legal and regulatory information cambium networks end user license agreement apache apache license version 2.0, january 2004 http://www.Apache.Org/licenses/ terms and conditions for use, reproduction, and distribution 1. Definitions. "license" shall mean the terms and conditions for use, ...
Page 266
Chapter 4: legal and regulatory information cambium networks end user license agreement means any form of electronic, verbal, or written communication sent to the licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and...
Page 267
Chapter 4: legal and regulatory information cambium networks end user license agreement within a display generated by the derivative works, if and wherever such third-party notices normally appear. The contents of the notice file are for informational purposes only and do not modify the license. You...
Page 268
Chapter 4: legal and regulatory information cambium networks end user license agreement of your accepting any such warranty or additional liability. End of terms and conditions appendix: how to apply the apache license to your work. To apply the apache license to your work, attach the following boil...
Page 269: D3 Js Library
Chapter 4: legal and regulatory information cambium networks end user license agreement d3 js library copyright (c) 2013, michael bostock all rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met...
Page 270
Chapter 4: legal and regulatory information compliance with safety standards compliance with safety standards this section lists the safety specifications against which the ptp 700 has been tested and certified. It also describes how to keep rf exposure within safe limits. Electrical safety complian...
Page 271
Chapter 4: legal and regulatory information compliance with safety standards • ansi ieee c95.1-1991, ieee standard for safety levels with respect to human exposure to radio frequency electromagnetic fields, 3 khz to 300 ghz. • council recommendation of 12 july 1999 on the limitation of exposure of t...
Page 272: Calculated Distances
Chapter 4: legal and regulatory information compliance with safety standards calculation of power density the following calculation is based on the ansi ieee c95.1-1991 method, as that provides a worst case analysis. Details of the assessment to en50383:2002 can be provided, if required. Peak power ...
Page 273: Antenna Gains
Chapter 4: legal and regulatory information compliance with safety standards table 102 minimum safe distances for ptp 700 at maximum transmitter power antenna p (w) (*1) g (*2) d (m) (*3) parabolic 6 ft (38.1 dbi) 0.635 5248.1 5.15 flat plate 2 ft (28.5 dbi) 0.635 575.4 1.71 integrated (21.0 dbi) 0....
Page 274
Chapter 4: legal and regulatory information compliance with safety standards table 103 minimum safe distances for fcc bands band antenna p (w) (*1) g (*2) d (m) (*3) 4.9 ghz parabolic 6 ft (37.2 dbi) 0.127 4265.8 2.07 flat plate (28.0 dbi) 0.326 512.9 1.15 sectorized (17.0 dbi) 0.333 40.7 0.33 omni ...
Page 275: Atex
Chapter 4: legal and regulatory information compliance with safety standards hazardous location compliance the ptp 700 atex/hazloc odus have been certified for operation in the following hazardous locations: atex the products have been approved under an “intrinsic safety” assessment as defined in en...
Page 276
Chapter 4: legal and regulatory information compliance with radio regulations compliance with radio regulations this section describes how the ptp 700 complies with the radio regulations that are in force in various countries. Caution where necessary, the end user is responsible for obtaining any na...
Page 277: Type Approvals
Chapter 4: legal and regulatory information compliance with radio regulations type approvals the system has been tested against various local technical regulations and found to comply. Table 104 to table 108 list the radio specification type approvals that have been granted for ptp 700 products. Som...
Page 278: Fcc/ic Compliance
Chapter 4: legal and regulatory information compliance with radio regulations table 108 radio certifications (5.8 ghz) region regulatory approvals usa fcc 47 cfr part 15 c canada ic rss-210 issue 8, annex 8 (or latest) denmark radio interface 00 007 eire comreg 02/71r4 germany order no 47/2007 icela...
Page 279
Chapter 4: legal and regulatory information compliance with radio regulations figure 106 fcc and ic certifications on connectorized+integrated odu product labels figure 107 fcc and ic certifications on connectorized odu product labels industry canada product labels industry canada certification numb...
Page 280: 5.1 Ghz Fcc Notification
Chapter 4: legal and regulatory information compliance with radio regulations figure 109 ic certification on connectorized odu product labels 4.9 ghz fcc and ic notification the system has been approved under fcc part 90 and industry canada rss-111 for public safety agency usage. The installer or op...
Page 281: 5.8 Ghz Fcc Notification
Chapter 4: legal and regulatory information compliance with radio regulations utilisation de la bande 5.4 ghz fcc et ic cet appareil est conforme à la section 15e de la réglementation fcc aux États-unis et aux règlementations et avec industrie canada rss-210 annexe 9. Son fonctionnement est soumis a...
Page 282
Chapter 4: legal and regulatory information compliance with radio regulations the ptp 700 takes into account the antenna gain and cable loss configured by the professional installer in the web-based interface to limit the eirp to ensure regulatory compliance. No additional action is required by the ...
Page 283
Chapter 4: legal and regulatory information compliance with radio regulations the maximum eirp in band edge channels for the usa and canada 5.2 ghz band is listed in table 110 . Table 110 edge channel power reduction in regulatory band 38 channel bandwidth channel frequency maximum eirp 5 mhz below ...
Page 284
Chapter 4: legal and regulatory information compliance with radio regulations réduction de puissance aux bords de la bande 5.4 ghz la puissance isotrope rayonnée équivalente (pire) est limitée dans les canaux en bord de la bandes lorsque le ptp 700 est configuré pour utiliser la band 5,4 ghz aux les...
Page 285: Selection Of Antennas
Chapter 4: legal and regulatory information compliance with radio regulations the maximum transmitter power in band edge channels for the fcc 5.8 ghz band is listed in table 112 . Réduction de puissance aux bords de la bande 5.8 ghz la puissance isotrope rayonnée équivalente (pire) est limitée dans ...
Page 286: European Union Compliance
Chapter 4: legal and regulatory information compliance with radio regulations note under industry canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by industry canada. To reduce potential radio interferenc...
Page 287
Chapter 4: legal and regulatory information compliance with radio regulations figure 111 european union certification on connectorized odu product label 5.4 ghz european union notification the ptp 700 product is a two-way radio transceiver suitable for use in broadband wireless access system (was), ...
Page 288
Chapter 4: legal and regulatory information compliance with radio regulations 5.8 ghz operation in the uk the ptp 700 connectorized product has been notified for operation in the uk, and when operated in accordance with instructions for use it is compliant with uk interface requirement ir2007. For u...