Summary of CSW-10AT
Page 2
Table of contents meter connections ---------------------------------------------------------- 3 1.0 operation ---------------------------------------------------------------- 4 1.1 key functions -------------------------------------------------------- 4 1.2 error messages --------------------------...
Page 3
To connect power via ac wall adapter cable to the csw-10at meter. First make sure the on/off switch on the rear of meter is in the off position. Connect the transformer to y your 110vac outlet. Next, connect the other end of the cable to the rear of the meter for power. Meter connections communicati...
Page 4: 1.1 Key Functions:
1.1 key functions: zero brings the scale to a zero balance reading. If the zero key is pressed and held for 5 seconds the calibration zero value will be displayed. Grs/net toggles the display between gross weight and net weight. This key is also used to enter setup mode. Begin by pressing and holdin...
Page 5
2.1 software navigation flowchart scale calibration rs-232 test end s1 ntep ntep,no,angle (ntep) s2 capacity 1-999,999 (5000) s3 count by 1,2,5,/dec (1) s4 overload 105% of cap or entered s5 zero limit s6 filter s7 motion band s8 motion delay 100%,1.9% (100%) 0 fastest to 7 slowest (3) 1 to 99 divis...
Page 6
2.2 navigation keys during setup you will be required to make numeric entries. (ex: capacity, zero band, etc...) the following table outlines the keys used to perform these entries along with their function. Zero-------key is used to navigate up. Grs/net---key is used to navigate down. Tare--------k...
Page 7: 2.3 Scale Menu Definitions:
2.3 scale menu definitions: s1 ntep (ntep): maximum divisions limited to 5 ,000. Scale negative message is displayed if the gross weight goes more than 10 divisions below zero. If a capacity and count by of more than 5 ,000 divisions is selected err d will be displayed and you will be returned to s2...
Page 8: End
2.3 scale menu definitions continued: s11 zero delay 0 to 99 updates (4) the weight display must be within the zero band for the selected number of updates to be considered zero. S12 zero tracking 1 to 99 divisions (2) the number of graduations allowed to be automatically zeroed off. S13 tracking de...
Page 9: 2.4 Numeric Entries
2.4 numeric entries when entering a numeric value, first press and release the lb/kg key to move right into the menu where the numeric value will be entered. Then press and release the zero key, the first digit in the value will flash. Press and release the zero and grs/net keys to increase or decre...
Page 10: C2 Zero
3.1 calibration menu definitions: c1 zero all raw counts, (pitch and roll if in angle mode) will be displayed. When zero is pressed an analog zero is done and all calibration span points will be cleared. If in angle mode the pitch and roll offsets will also be zeroed. C2 zero zeroed raw counts, (pit...
Page 11: 3.2 Calibration
3.2 calibration press and hold the grs/net key, as d escribed previously in section 2.5. Scale will be displayed. Press the lb/kg key to move right, calib will be displayed. Press the grs/net key to move down, c1 will be displayed. Press the lb/kg key to move right, the raw counts will be displayed....
Page 12
4.1 communications menu definitions: r1 baud rate 1200 to 115200 baud (9600), 8, n, 1 r2 output 0 - (gross, tare, net)- "cr, lf, cr, lf [32 bytes of 2eh], format cr, lf, cr, lf, gross (lb or kg), :, six ascii characters [indicated weight], cr, lf, tare (lb or kg), sp, :, six ascii characters (indica...
Page 13: End
4.1 communications menu definitions continued: r4 receiver 0 - disabled - normal scale mode. 1 - standard receiver. Receives r3.3 rf link output string displaying data as it appears on the scale. All keys are disabled except the print key . 2 - remote control. Receives r3.3 rf link output string dis...
Page 14: T2 Display
5.1 testing menu definitions: t1 version displays software version. T2 display lights all display segments and indicating led s t3 buttons press the zero key, b1 will be displayed. Press the grs/net key, b2 will be displayed. Press the tare key, b3 will be displayed. Press the lb/kg key, b4 will be ...
Page 15: Cambridge
Cambridge warrants the csw-10at to be free of defects in workmanship and/or materials for 12 months from the date of shipment. This warranty of workmanship and/or materials is valid, if in the opinion of cambridge , the equipment has not been mechanically, environmentally, or electrically abused. Th...
Page 16: Cambridge Scale Works, Inc.
If at any time you require assistance with your model: csw-10at meter please contact us at: cambridge scale works, inc. 115 west mary street cumberland, md 21502 phone: (301) 724-4082 fax: (301) 724-4964 7.0 assistance cambridge scale works, inc. 16 manual p/n 5999-1014-01.