CAMBRIDGE CXU Manual - Cxu
7
CXU
Rear panel connections
1. Ethernet LAN port
Used for Playback of context from the Internet or Network attached storage
drives and servers, also used for discs supporting BD-Live that provide
interactive features when the player is connected to the Internet.
2. HDMI input
This input is used to connect to a source device such as a set-top box or
other HDMI Source.
3. Diagnostic video
Use for diagnostic purposes. Connect to a TV/Monitor via a 75 ohms RCA/
7OVUVJHISLKLZPNULKZWLJPÄJHSS`MVY]PKLV\ZL
4. Digital outputs
Optical and Coaxial digital audio outputs, optionally used to connect to a
suitable Audio/Video Receiver for surround sound decoding (output must
be set for "Bitstream". Refer to the "Audio setup" section). HDMI is however
the preferred correction to AV Receivers as the latest lossless CODECS are
only supported over HDMI. These outputs can also be used to connect to a
separate DAC or digital recording device (output must be set for "LPCM".
Refer to the "Audio setup" section).
TOSlink Optical
¶ S/P DIF Coaxial Digital – Use a high quality 75 ohm digital RCA/Phono PU[LYJVUULJ[JHISLKLZPNULKZWLJPÄJHSS`MVYKPNP[HSH\KPV\ZL 5. HDMI output 2 Secondary HDMI output. Both outputs 1 and 2 can be used at the same time to send the same audio/video to two displays (with both being 3D TV compatible) or to send audio over one HDMI link and video over the other. (S^H`Z\ZLH/+40/PNO:WLLKJLY[PÄLK*HISL HDMI 1 and 2 both support Audio Return Channel from TVs that have this function. See later section. 6. HDMI output 1 (primary output) ;OL/+40/PNO+LÄUP[PVU4\S[PTLKPH0U[LYMHJLPZHW\YLS`KPNP[HSJVUULJ[PVU that can carry both audio and video. Use a dedicated HDMI cable to connect to a TV/Monitor or AV Receiver with a compatible HDMI input. (S^H`Z\ZLH/+40/PNO:WLLKJLY[PÄLK*HISL ;OPZ V\[W\[ PZ [OL WYPTHY` V\[W\[ HUK ILULÄ[Z MYVT [OL +HYILL ]PKLV processor. Both this output and output 2 are 3D TV compatible. HDMI 1 and 2 both support Audio Return Channel from TVs that have this function. See later section. 7. USB port 1 and 2 7VY[MVYPU[LYMHJPUN[VHÅHZOTLTVY`JHYKVY4HZZ:[VYHNL+L]PJLZ\JOHZ a portable hard-drive). Notes: – This unit supports USB Mass Storage Class Bulk Transport devices only. Most USB thumb drives, portable hard disk drives and card readers conform to this device class. Other USB devices such as MP3 players, digital cameras, and mobile phones that include their own memory management may not be compatible. – Supported USB drives must be formatted with the FAT (File Allocation ;HISL-(;VY5;-:5L^;LJOUVSVN`-PSL:`Z[LTÄSLZ`Z[LT – In some cases, an incompatible USB device may cause the player to stop YLZWVUKPUN 0M [OPZ VJJ\YZ ZPTWS` [\YU VɈ [OL WV^LY YLTV]L [OL <:) device, and turn the player back on. – The player accesses the USB drive in read-only mode. In order to minimize the risk of data corruption, it is recommended that you only unplug the USB device when playback has completely stopped. 8. IR (Infra-Red) emitter in Allows modulated IR commands from multi-room systems or IR repeater systems to be received by the unit. 9. RS232C Used for control of the CXU in Custom Install situations. A full protocol is available for the CXU on our website. 10. 7.1 channel analogue audio output If Down-mix is set to "7.1 CH" in the Speaker Setup page (Down-mix mode section) of the CXU's Setup menus, these sockets provide 7.1 output from the CXU's built in Surround-Sound decoder. This can be used to connect to [OLH\KPVSPULSL]LSPUW\[ZVMHUHTWSPÄLY(=YLJLP]LYVYHTWSPÄLKZWLHRLY package if required. Similarly, Down-mix can be set to "5.1 CH" to provide 5.1 output. If Down-mix is set to "LT/RT", "Stereo" or "V.Surround" the Left and Right outputs only are active and provide a stereo or stereo downmixed V\[W\[9LMLY[V[OL:WLHRLYJVUÄN\YH[PVUZLJ[PVUVM[OPZTHU\HSMVYTVYL information. 11. Digital input Optical and Coaxial digital audio inputs, used to connect to: TOSlink Optical ¶ S/P DIF Coaxial Digital – Use a high quality 75 ohm digital RCA/Phono PU[LYJVUULJ[JHISLKLZPNULKZWLJPÄJHSS`MVYKPNP[HSH\KPV\ZL 12. Stereo audio out Permanent stereo outputs for use with Stereo material. 13. AC power socket Once you have made all audio and video connections, plug the IEC type AC power cable into the rear of the unit and an appropriate mains socket then switch on. Your CXU is now ready for use. 7.1 Channel Audio Out Stereo Audio Out FL SL C SBL Right Left FR SR SW SBR Digital Outputs Diagnostic Video Digital Inputs HDMI Input HDMI Out 2 HDMI Out 1 Ethernet USB Coax RS-232C Optical Coax Composite Optical In 2 1 IR Emitter Power AC 1 2 5 6 7 3 4 8 10 12 13 9 11