- DL manuals
- CAMBRIDGE
- Conference System
- Qt Conference Room Edition
- Installation And Operation Manual
CAMBRIDGE Qt Conference Room Edition Installation And Operation Manual
Summary of Qt Conference Room Edition
Page 1
Qt ® conference room edition a speech protection system designed for conference rooms installation and operations guide.
Page 2
Page 3 qt conference room edition installation and operations guide safety safety important safety instructions: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. Indoor use only. 6. Clean only with dry ...
Page 3
Page 4 qt conference room edition installation and operations guide packing list the package includes: ▪ 1 wall-mounted st 1000 control module ▪ 1 4-gang adaptor plate for control module (used for 3-gang eu/uk boxes) ▪ 2 automatically lighted privacy signs ▪ 2 1-gang adaptor plate for privacy signs ...
Page 4
Page 8 qt conference room edition installation and operations guide planning the system emitter spacing and ceiling height spacing between emitters generally should follow the same rules as for other csm direct field masking systems, i.E. Should be not less than the ceiling height above the finished...
Page 5
Page 12 qt conference room edition installation and operations guide installation installation pre-wiring homerun the 50’ cat distribution line supplied with the base kit should be sufficient as the homerun for almost all installations. It may be replaced by a longer cat cable to the first emitter w...
Page 6
Page 13 qt conference room edition installation and operations guide installation power supply in most cases the 24v power supply will need to be located remotely, with a cable run from the power supply to the controller. In some cases a wall plate such as the vanco 120614x permits in-wall running o...
Page 7
Page 14 qt conference room edition installation and operations guide usb connection (special purpose see page 14) sign is active usb connection in use installation note that the small switch on the side of the controller must be set to the “up” position (closer to the top of the case) for the lights...
Page 8
Page 15 qt conference room edition installation and operations guide installation installing qt emitters important considerations: ▪ each run has a maximum of 60 emitters! ▪ each run supports a maximum cable length of 1000 ft. ▪ each home run cable attached to the control module should be labeled by...
Page 9
Page 16 qt conference room edition installation and operations guide installation 8. Run the cable to next designated tile specified on emitter layout and wiring diagram. Tie cables up to structure or suspend from deck as required by local building code. 9. On the next emitter, connect this cable to...
Page 10
Page 17 qt conference room edition installation and operations guide installation custom cabling guidelines installing the controller and privacy signs important considerations: 1. Use solid conductor 24 awg cat cable that meets local code requirements. 2. If the system is installed in a return air ...
Page 11
Page 18 qt conference room edition installation and operations guide installation flush mount with supplied box cut hole in wall to dimensions x by x (use template) and run cables to this hole. After the cables have been run to the hole in the wall, place the flush mount box in the wall (make sure u...
Page 12
Page 19 qt conference room edition installation and operations guide surface mount on a suitable 4-gang electrical box (3-gang using eu/uk hardware) 4-gang electrical box (pre-installed or retrofitted) – after the cables have been run to the box, use four supplied screws to attach the wall plate ada...
Page 13
Page 20 qt conference room edition installation and operations guide installation surface mount directly to the wall surface or panel mount of back plate – either with cables through hole (if cables can be run through the wall) or out the side to end up on the surface of the wall or mounting point. ...
Page 14
Page 21 qt conference room edition installation and operations guide installation mounting options for the privacy signs there are several options for mounting the privacy signs. These options allow for mounting on a variety of wall surfaces, including glass. 1-gang box (north american nema or uk/eu...
Page 15
Page 22 qt conference room edition installation and operations guide surface mount (double-sided tape), with cabling running through wall or on surface of wall. If running a cable through the wall, get this into position first. Note that the exit point for the cable on the back of the sign is center...
Page 16
Page 23 qt conference room edition installation and operations guide installation mounting on glass plus using “hider” plate for other side of glass surface best practices – it’s best to use self-adhesive tape, not a 1-gang box (because of sound transmission issues). If mounting the signs to either ...
Page 17
Page 34 qt conference room edition installation and operations guide zone destination records zone destination record zone 1 run 1 run 2 settings record volumes: zone: 1 masking: input a: installation / service: company name: install date: phone:.
Page 18
Page 35 qt conference room edition installation and operations guide 4 7 / 16 in. 113mm hole cut out line flush mount box out line contr ol module out line 8 5 / 16 in. 211mm 7 1 / 2 in. 190mm 3 3 / 4 in. 95mm up hole cut guide for flush mount box cut hole to 7 1 / 2 in. (190mm) by 3 3 / 4 in. (95mm...
Page 19
Page 36 qt conference room edition installation and operations guide.
Page 20
Page 37 qt conference room edition installation and operations guide 4 7 / 16 in. 113mm wire exit area 3 1 / 2 in. 90mm hole cut guide for privacy sign cut hole wire 1 / 4 in (6mm) from lower edge of sign hole shape is not important, but be careful to stay within area to be covered by sign. Remember...
Page 21
Cambridge sound management, inc. 404 wyman st. Suite 200 waltham, ma 02451 usa cambridgesound.Com © copyright 2015 cambridge sound management inc. Quiet technology, qt, cambridge sound management, and the logo are trademarks of cambridge sound management..
Page 22: Conference
This two page document is an addendum to the qt ® conference room edition manual. Please read. Note: below are supplemental images for the content contained on page 14 of the qt ® conference room edition manual. Connection to privacy signs run a separate cable from the controller mounting location t...
Page 23: Conference
This two page document is an addendum to the qt ® conference room edition manual. Please read. Note: two new options have been added to the program menu of the qt ® conference room edition. These options are outlined below: 1. Contact closure = normal/off or normal/low. When this option is set to “n...