1. DL manuals
  2. CAME
  3. Control Panel
  4. ZE5 V.7
  5. Installation Manual

CAME ZE5 V.7 Installation Manual

Manual is about: Control panel for Emega series

Summary of ZE5 V.7

  • Page 1

    Ze5 v .7 automazione per chiusura industriale installation manual control panel for emega series.

  • Page 2

    A ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . 2 english the ze5 electrical panel is designed to control emega (e306-e456) automation units in the movement of garage-type door...

  • Page 3

    3 a ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . English 4.3 main components before proceeding with the installation, it is necessary to: • make sure the mains power is off. •...

  • Page 4

    A ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . 4 english 5.3 dimensions, axle bases and fastening holes 5.4 minimum thicknesses and cables types #!-% mm mm mm connections cabl...

  • Page 5

    5 a ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . English rosso nero fa k e w v u f 5.5 pre-settings, fixing the electric board to the ground guide (art. 001e001) and ratiomoto...

  • Page 6

    A ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . 6 english 5.6 connections line -enc+ ze7 control 5a board f u s e 5 x 2 0 l n v w u e1 e3 10 10 11 11 1 2 3 5 7 c1 c1 fa fa l n ...

  • Page 7

    7 a ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . English 5.7 dip-switch functions 5.8 trimmer adjustments 1 on automatic closing activated; 2 on “open-stop-close-stop” with ke...

  • Page 8

    A ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . 8 english mm 5.9 encoder programming cam end-stop micro- switch important: read instructions carefully before proceeding with pr...

  • Page 9

    9 a ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . English opening end-stop press “ch1/op” and allow the door to open completely. Acces. Line -a.C.T.+ -enc+ 1 2 3 4 5 6 7 8 9 1 ...

  • Page 10

    A ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . 10 english 5.10 connecting two motors should two motors be installed, connect them in parallel. Use terminals u, v and w of the ...

  • Page 11

    Please read the following instructions carefully prior to installation: - preparing the radio board (par. 6.1); - transmitter encoding procedure (par. 6.2); - control board code memorisation (par. 6.3). 2) the af board should be mandatorily inserted only when the mains power is off, because the moth...

  • Page 12

    0 0 the fi rst code should be recorded by keeping the jumpers positioned for channels 1 and 2 as in fi g. A; see fi g. B for any further settings on different channels. Top t262m - t302m fig.A fig.B 0 0 0 0 t264m - t304m 0 0 0 0 /. /&& 0 0 t2622m - t3022m p1 = ch1 p2 = ch2 p3 = ch3 p4 = ch4 p1 = ch1...

  • Page 13

    0 0 /. /. /. /. /. /. /. /. Top t432m - t312m set the code to dip-switch c and the channel to d (p1 = ch1 and p2 = ch2, default setting) d c p1 ch1 top t434m - t314m 0 0 0 0 c set the code only p1 = ch1 p2 = ch2 p3 = ch3 p4 = ch4 top t432s - t432sa - t434ma - t432na - t434na see instructions in the ...

  • Page 14

    -keep the “ch1/op” key pressed down on the control board (the led indicator fl ashes); - the code is sent by means of a transmitter key, and the led indicator will remain lighted to signal that that the garage door does not move: - check the 230 v ac power supply on terminals l-n. - check the fuses....

  • Page 15: Manufacturer’S Declaration

    15 a ll t h e d a ta a n d i n fo rm a ti o n c o n ta in e d h er e in i s c o n s id er e d s u b je c t t o c h a n g e a t a n y t im e a n d a t o u r d is c re ti o n . English 8 demolition and disposal in its premises, came cancelli automatici s.P.A. Implements an environmental management sys...

  • Page 16

    Ze5 v 0 .7 _ 3 19t92 v o 1 came united kingdom ltd unit 3, orchard business park town street, sandiacre nottingham - ng10 5bp - u.K. Tel 0044 115 9210430 fax 0044 115 9210431.