Cameo CLMFXBAR User Manual - page 21
21
UP/DOWN
-> ENTER
-> ENTER->
COLOUR MIXING (CoLo)
This mode offers the ability to separately adjust the brightness of the 4 colours of the LED spotlight and to simultaneously adjust the 3 colours of the
Derby effects. Up to 3 colours of the LED spotlights can be activated at the same time; the value of at least one colour must therefore be set to 000.
Press the MODE button repeatedly until “CoLo” appears on the display. Press the ENTER button and adjust the brightness of the red LEDs using the
UP and DOWN buttons (r000 - r255) and confirm with ENTER. Now you can adjust the brightness of the green, blue and UV LEDs in the same way
(G000 - G255, b000 - b255, u000 - u255). After you have confirmed with ENTER, the strobe effect can now be activated. Using the UP and DOWN
buttons, you can set the stroboscope speed as desired and confirm with ENTER (F 00 = strobe disabled, F 01 = slowest and F 99 = fastest flash
frequency). The display now shows “CoLo” again. After approximately 30 seconds of inactivity, the characters on the display will go out.
-> ENTER
-> ENTER ->
<- MODE
-> ENTER ->
<- MODE
-> ENTER ->
<- MODE
UP/DOWN
UP/DOWN
UP/DOWN
-> ENTER ->
<- MODE
-> ENTER ->
<- MODE
UP/DOWN
UP/DOWN
AUTOMATIC CONTROL MODE (Auto)
Press the MODE button repeatedly until “Auto” appears on the display. Press ENTER again to select one of the 46 automatically running programs
using the UP and DOWN buttons (For programs see the DMX table 2-channel mode, channel 1). After confirming by pressing the ENTER button, you
can now select the speed at which the selected program runs by using the UP and DOWN buttons (SP01 = minimum speed, SP99 = maximum
speed). Confirm with ENTER. The display now shows “Auto” again. After approximately 30 seconds of inactivity, the characters on the display will go
out.
-> ENTER
UP/DOWN
-> ENTER ->
<- MODE
UP/DOWN
-> ENTER ->
<- MODE
MUSIC CONTROL MODE (Soun)
Press the MODE button repeatedly until “Soun” appears on the display. Press ENTER again to select one of the 46 automatically running programs
using the UP and DOWN buttons (For programs see the DMX table 2-channel mode, channel 1). Confirm with ENTER. The display now shows “Soun”
again. After approximately 30 seconds of inactivity, the characters on the display will go out. To adjust the sensitivity with which the programs react
to sounds (bass pulses), use the MIC SENSITIVITY controller as desired. When turned to the left, the sensitivity is lowered, when turned to the right, it
is increased.
-> ENTER
UP/DOWN
-> ENTER
<- MODE
SLAVE MODE
Press the MODE button repeatedly until “SLAv” appears on the display and confirm by pressing ENTER to activate the slave mode. If no control signal
is present, the characters in the display flash; the flashing stops as soon as a control signal is present. Connect the slave and the master unit (same
model) using a DMX cable (Master = DMX OUT, Slave = DMX IN) and activate one of the standalone modes (automatic control, music control, colour
mixing) on the master unit. Now the slave unit follows the master unit. After about 30 seconds of inactivity, the characters in the display will go out
and an LED dot appears in the bottom right of the display. If no control signal is present, the LED dot in the display flashes; the flashing stops as soon
as a control signal is present.
CONTROL VIA WIRELESS FOOT SWITCH (Foot)
To control the lighting system via wireless foot switch, the wireless connection must be activated (Foot = on). Press the MODE button repeatedly until
“Foot” appears on the display and confirm by pressing ENTER. Now use the UP and DOWN buttons to select the “on” entry and confirm by pressing
ENTER. If the foot switch is not used, please disable the wireless connection (Foot = off). You will find instructions for using the wireless foot switch
in the WIRELESS FOOT SWITCH section of this manual.
-> ENTER ->
<- MODE
UP/DOWN
-> ENTER
DE
Wenige Sekunden nach dem Anschließen an das Stromnetz ist der Effekt-Strahler betriebsbereit und die Betriebsart, die zuvor angewählt war,
wird aktiviert. Während des Startvorgangs wird kurz die Software Version angezeigt (Vx.xx).
DMX-STEUERUNG AKTIVIEREN UND DMX-STARTADRESSE EINSTELLEN
Drücken Sie die MODE-Taste so oft, bis im Display „Addr“ angezeigt wird. Drücken Sie nun auf ENTER, um die DMX-Steuerung zu aktivieren und die
aktuell eingestellte DMX-Startadresse anzeigen zu lassen. Alle vier Zeichen im Display blinken, falls kein DMX-Signal anliegt, wenn ein DMX-Signal
anliegt, stoppt das Blinken der Zeichen im Display. Stellen Sie nun die gewünschte DMX-Startadresse mit Hilfe der Tasten UP und DOWN ein und
bestätigen die Eingabe mit ENTER (02Ch Mode = A001 - A511, 05Ch Mode = A001 - A508, 29Ch Mode = A001 - A484). Nach ca. 30 Sekunden Inak-
tivität erlöschen die Zeichen im Display und ein LED-Punkt rechts unten im Display wird angezeigt. Liegt kein Steuersignal an, blinkt der LED-Punkt,
das Blinken stoppt, sobald ein Steuersignal anliegt.
-> ENTER
UP/DOWN
-> ENTER
DMX-BETRIEBSART EINSTELLEN
Drücken Sie die MODE-Taste so oft, bis im Display „CHAn“ angezeigt wird, drücken auf ENTER und wählen nun eine der 3 verfügbaren DMX-Be-
triebsarten mit Hilfe der Tasten UP und DOWN aus (02Ch, 05Ch, 29Ch). Bestätigen Sie die Eingabe mit ENTER. Daraufhin wird die aktuell eingestellte
DMX-Startadresse angezeigt. Nach ca. 30 Sekunden Inaktivität erlöschen die Zeichen im Display. Tabellen mit der Kanalbelegung der verschiedenen
DMX-Modi finden Sie in dieser Anleitung unter DMX STEUERUNG.