Campbell Hausfeld WS2800 Operating Instructions & Parts Manual

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

IN971400AV 8/04

Operating Instructions & Parts Manual   

Model WS2800

Shielded Metal 

Arc Welder

BUILT TO LAST

Description

This Campbell Hausfeld electric arc

welding machine runs on 230 volt,

single phase input power. This welder

is equipped with infinite amperage

control to accurately select the proper

current needed for various welding

conditions. Internal components are

thermostatically protected.

This welding system is designed for use

with the Shielded Metal Arc Welding

(SMAW) process. As delivered from the

factory, this welder can weld with up

to 5/32" diameter electrodes.

Unpacking

When unpacking, inspect carefully for

any damage that may have occurred

during transit. Make sure any loose

fittings and screws, etc. are tightened

before putting unit into service.

Circuit Requirements

This equipment 

requires a

dedicated 230 volt circuit. Refer to the

following chart for the correct circuit

breaker or fuse rating. Do not run

other appliances, lights, or tools on

this circuit while operating this

equipment. Extension cords are not

recommended. Blown fuses and tripped

circuit breakers can result from failure

to comply with this recommendation.

Specifications

Rated Input Voltage . . . . . . . . .230v AC

Rated Input Amperage  . . . . .See chart

Power Cord Length  . . . . . . . . . . . . .6 FT

Electrode Cord Length  . . . . . . . . .10 FT

Grounding Cord Length  . . . . . . . .10 FT

Cycles  . . . . . . . . . . . . . . . . . . . . . . .60 Hz

!

CAUTION

The electrode

holder is "live"

(has current potential) when machine is

turned on.

Components and Controls

1. Work Clamp – connect to work piece

2. Electrode Holder – holds  welding

electrode.

3. Power Cord – plug into 230 volt outlet.

4. On/Off Switch.

5. Infinite Amperage Control Knob –

turns clockwise to increase amperage

and counterclockwise to decrease

amperage.

6. Welding Amp Indicator – as the

amperage control knob (5) is rotated,

the amperage indicator moves,

displaying approximate weld amps.

7. Overload Indicator Light – lights when

duty cycle exceeded.

8. Power Indicator Light – lights when

unit is energized.

General Safety

Danger means a

hazard that will

!

DANGER

!

WARNING

Weld

Circuit Breaker or

Current

Slow Blow Fuse

AC

50 amp

cause death or serious injury if the

warning is ignored.

Warning means a

hazard that could

cause death or serious injury if the

warning is ignored.

Caution means a

hazard that may

cause minor or moderate injury if the

warning is ignored. It also may mean a

hazard that will only cause damage to

property.

Note:  Note means any additional

information pertaining to the product

or its proper usage.

Always 

keep a

fire extinguisher accessible

while performing arc

welding operations.

 Before starting or servicing any

electric arc welder, read and

understand all instructions. Failure

to follow safety precautions or

instructions can cause equipment

damage and or serious personal

injury or death. For additional

safety information, obtain a copy of

!

WARNING

!

CAUTION

!

WARNING

For parts, manuals, product & service information

visit www.chpower.com

or call 800-746-5641

© 2004 Campbell Hausfeld/Scott Fetzer

Weld Voltage

31v AC

Weld Amps

180a AC

Duty Cycle

20%

Max. Open

Circuit Voltage

65 Volt AC

1

2

3

4

8

7

5

6

Figure 1 - Welder Components and Controls

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

40

Notes

Manual de instrucciones y lista de repuestos