03/10 installation instructions pacific wind - energy star note: for optimum quietness, fully assemble fan and run for 24 hours questions or concerns contact canarm at: 1-800-265-1833 (english) 1-800-567-2513 (french) monday through friday 8:00 a.M. To 5:00 p.M. Est important for your records, recor...
1. Turn off power at main electrical service box before starting installation. 2. Electrical connections must comply with local code ordinances or national electrical codes. 3. Make sure the installation site you choose allows the fan blades to rotate freely without any obstructions. 4. When mountin...
Pg. 3 assembly drawing 1. Wooden joist 2. Metal outlet box (not provided) 3. Ceiling 4. Rubber gasket 5. Mounting bracket 6. Outlet box screws 7. Wood screws & flat washers 8. Downrod 9. Canopy 10. Bolt 11. Cotter pin 12. Motor 13. Blade bracket screw 14. Fibre washer 15. Blade 16. Rubber washer 17....
Pg. 4 • obtain fan motor • remove cotter pin and bolt from yoke • loosen jam screw in yoke until it is flush with the inside surface • obtain dowrod and canopy (and yoke cover - optional) • place downrod inside canopy (and yoke cover - optional) • route wires and safety cable exiting motor through c...
Pg. 5 • secure rubber gasket and mounting bracket to metal outlet box using outlet box screws • secure once more by placing two wood screws and flat washers (supplied) through outer slots of mounting bracket and into the wood joist. Leave one of the wood screws sufficiently loose to allow the safety...
Pg. 6 • obtain fan and place hemisphere of downrod into mounting bracket • rotate fan until the slot in the hemisphere locks into the tab of the mounting bracket • place looped end of safety cable over the wood screw and flat washer not previously tightened (in step 3) • tighten above wood screw sec...
Pg. 7 there are several different wiring combinations that can be used in controlling your ceilingfan to meet your specific requirements. Should the following method not meet your requirements call or visit your nearest canarm distributor for a full list of fan accessories. 4. Electrical hookup inst...
Pg. 8 installation b. Connecting black, white & (blue or red) wires 4. Electrical hookup (continued) • connect white wire from outlet box to white wire from fan using marrette (not supplied). • connect black wire from outlet box to black wire from fan plus (red or blue wire) using a marrette. Note: ...
Pg. 9 5. Mounting fan assembly installation • loosen two screws and washers (b) on mounting bracket which correspond with the slots in the canopy • remove two screws and washers (a) on the mounting bracket which correspond with the oblong holes in the canopy. • position the canopy to the mounting br...
Pg. 10 6. Mounting blade brackets to blades installation a. “diecast” blade brackets • obtain hardware package containing blade bracket screws and washers. • place fibre washer over screw. • place screw through blade hole and slip a rubber washer over the screw. • align screw with blade bracket and ...
Pg. 11 7. Mounting blade brackets to blades to motor installation note: choice of 4 or 5 blades (option on some fans) some fans offer the option of four or five blade operation. In these cases there will be two rows of screw holes in the motor casing. The inside row will contain 8 holes for 4 blades...
Pg. 12 8. Detachable light kits installation warning: be sure to turn off power before installing • remove light kit screws and washers. • connect polarized connectors of light kit to corresponding connectors found in switch housing • carefully tuck electrical wires back into switch housing, align l...
Pg. 13 8. Detachable light kits (continued) installation fig. E, f: • install proper wattage and type of bulb identified on light housing or shade. • place glass on light housing and secure fig. G: • remove 2 clips and nuts. Loosen third clip and nut. • place proper bulb type and wattage into the fi...
Pg. 14 instructions a ceiling fan has a totally internal switching system for total operation by way of pull chain on a fan/light combination. Three pull chains will exist. One for light, on and off. The second is for fan speeds. This will be marked (speed) on the fan switch housing. 1st pull will g...
Pg. 15 trouble shooting trouble suggestion fan will not start • check fuses and circuit breakers • check wiring connections to the fan • check wiring connections in switch housing *caution: turn power off for last two items fan sounds noisy • check to make sure that all screws in motor housing are s...
Canarm ltd. 2157 parkedale ave. Brockville, ontario k6v 5v6 ph: 613-342-5424 fx: 613-342-8437 canarm ltÉe. 2555 rue bernard lefebvre laval, quebec h7c 0a5 ph: 450-665-2535 fx: 450-665-0910 canarm 30 year limited warranty “thank you” for purchasing a canarm product. It is our policy to furnish you wi...
