Ws665 water softener owners man ual revision # 2 revision date september 12, 2013 followthe installation instructions carefully. Failure to install the unit properly voids the warranty. Before you begin installation, read this entire manual. Then, obtain all the materials and tools 1. Avoid pinched ...
2 safety guide check and comply with your provincial / state and local codes. You must follow these guidelines. Use care when handling the water soften- ing system. Do not turn upside down, drop, drag or set on sharp protrusions. The water softening system works on 12 volt-60 hz electrical power onl...
3 proper installation this water softening system must be properly installed and located in accordance with the installation instructions before it is used. Do not install or store where it will be exposed to temperatures below freezing or exposed to any type of weather. Water freezing in the system...
4 specifications before starting installation tools, pipe, and fittings, other materials pliers screwdriver teflon tape razor knife two adjustable wrenches additional tools may be required if modifi- cation to home plumbing is required. Plastic inlet and outlet fittings are included with the softene...
5 place the softener as close as possible to the pressure tank (well system) or water meter (city water). Place the softener as close as possible to a floor drain, or other acceptable drain point (laundry tub, sump, standpipe, etc.). Connect the softener to the main water supply pipe before the wate...
6 1. If your hot water tank is electric, turn off the power to it to avoid damage to the element in the tank. 2. If you have a private well, turn the power off to the pump and then shut off the main wa- ter shut off valve. If you have municipal water, simply shut off the main valve. Go to the faucet...
7 installation twin tank.
8 system start-up 1. Plug the power transformer into an ap- proved power source. Connect the power cord to the valve. 2. When power is supplied to the control, the screen will display “canature” while it finds the service position. 3. Manually step the valve past the brine position to the backwash p...
9 programming instructions manual regeneration (step / cycle valve) 1. Press settings to enter programming. If the system has been inactive, you may have to hold and press settings to unlock the display screen. Press up or down to select which setting to modify. 2. To adjust a value, manual regen. W...
10 operation during a power failure in the event of a power failure, the valve will keep track of the time and day for 48 hours. The programmed settings are stored in a non-volatile memory and will not be lost during a power failure. If power fails while the unit is in regeneration, the valve will f...
11 automatic hard water bypass during regeneration the regeneration cycle can last 30 to 180 minutes, after which soft water service will be re- stored. During regeneration, hard water is automatically bypassed for use in the household. Hot water should be used as little as possible during this time...
12 manual bypass in the case of emergency, such as an overflowing brine tank, you can isolate your water softener from the water supply using the bypass valve located at the back of the control. In normal operation the bypass is open with the on/off knobs in line with the inlet and outlet pipes. To ...
13 cleaning or replacing injectors sediment, salt and silt will restrict or clog the injector. A clean water supply and pure salt will prevent this from happening. The injector assembly is located on the right side of the control valve. This assembly is easy to clean. 1. Shut off the water supply to...
14 replacing brine line flow control (blfc) 1. Remove the red clip that secures the brine elbow. 2. Remove the blfc holder from the elbow fitting. 3. Split the blfc holder apart and remove the flow washer. 4. Reassemble using the reverse procedure. Tip: markings on the blfc washer should face the di...
15 care of your system to retain the attractive appearance of your new water softener, clean occasionally with mild soap solution. Do not use abrasive cleaners, ammonia or solvents. Never subject your sof- tener to freezing or to temperatures above 100°f. Resin cleaner an approved resin cleaner must...
16 main repair parts - connectors a a a b d f e a c replacement part number part description dwg # quantity 60010020 3/4" npt elbow a 2 60010019 1" npt straight a 2 60010023 3/4" npt straight a 2 60010079 valve coupling inlet b 1 60010101 valve coupling outlet (meter side) c 1 60010025 plastic secur...
17 control valve exploded view.
18 control valve parts list item no. Part no. Part discription quantity a01 05056087 screw-m5×12(hexagon) 3 a02 05056088 screw-m5×16(hexagon with washer) 2 a03 05056047 end plug retainer 1 a04 05010081 bnt65 piston rod 1 a05 05056097 piston pin 1 a06 05056023 end plug 1 a07 05056070 quad ring 2 a08 ...
19 power head exploded view.
20 power head parts list item no. Part no. Part description quantity b01 5056136 screw-st3.5×13(hexagon with washer) 4 b02 5056014 bnt65 back cover 1 b03 5010045 piston stem holder 1 a26 13000426 screw-st2.9×13(large wafer) 1 b04 5056139 washer-3x13 1 b05 5056005 main gear 1 b06 5056083 screw-m4x14 ...
21 trouble shooting issue possible cause possible solution 1. No power supply. Check electrical service, fuse, etc. 2. Defective circuit board. Replace faulty parts. 3. Power failure. Reset time of day. 4. Defective meter. Replace turbine meter. 1. By-pass valve open. Close by-pass valve. 2. Out of ...
22 warranty canature usa inc. Guarantees that your new water conditioner is built of quality material and workmanship. When properly installed and maintained, it will give years of trouble free service. Five year limited warranty canature usa inc. Will replace the salt tank or cabinet tank, the fibr...
