Candy GO 121054 L User Instructions - page 9
17
EN
PROGRAMME LOCK BUTTON
This is a useful feature to
prevent children playing with
the option buttons and
tampering with
the programme you have
set.
After you have set the
programme and option
buttons you require, press
START button
and then hold down
programme lock button for
few seconds until the symbol
“ ” will appear on the
display. This “locks” the control
panel.
You may cancel this function
by pressing the programme
lock button for few seconds
until the symbol “ ” will
disappear.
The option buttons should be
selected before pressing the
START button.
If an option is selected that is
not compatible with the
selected programme then
the light on the button first
flashes and then goes off.
“PRE-WASH” BUTTON
This option is particularly
useful for heavily soiled loads
and can be used only on
some programmes as shown
in the programmes table.
Detergent for this programme
should be added to the
compartment of the soap
drawer labelled “1” (Please
refer to Detergent Drawer
Section of manual). We
recommend you use only
20% of the recommended
quantities shown on the
detergent pack and fabric
conditioner should not be
used for this programme.
G
ES
OPCIÓN BLOQUEO TECLAS:
Esta función es útil para evitar
que los niños jueguen con las
opciones interfiriendo con el
programa de seleccionado.
Una vez seleccionado el
programa y las funciones
deseadas, accionar la tecla
START /PAUSA y
sucesivamente la opción
“BLOQUEO TECLAS” durante
unos segundos hasta que se
encienda el símbolo “ ”. De
esta manera el panel de
mandos se bloquea. Es
posible anular esta función
manteniendo presionado
“BLOQUEO TECLAS” hasta
que se apaga el símbolo “ ”.
Las teclas de opción
deberán estar seleccionadas
antes de pulsar la tecla de
START.
En caso de que se haya
seleccionado una opción no
compatible con el programa
elegido, la luz del botón
primero parpadeará y
después se apagará.
TECLA “PRELAVADO”
Esta opción es útil, sobre
todo, para la ropa muy sucia
y se puede utilizar sólo en
algunos programas tal y
como indica la tabla de
programas". Verter el
detergente para este
programa en el
compartimiento de la cubeta
marcado con “1” (para más
información, véase el
apartado “Cubeta del
detergente” de este manual).
Se recomienda utilizar sólo el
20% de la cantidad
recomendada en el
compartimento del
detergente.
H
16
“DELAY START” BUTTON
This button allows you to pre-
programme the wash cycle
to delay the start of the cycle
for up to 24 hours.
To delay the start use the
following procedure:
Set the required programme.
Press the button once to
activate it (h00 appears on
the display) and then press it
again to set a 1 hour delay
(h01 appears on the display);
the pre-set delay increases
by 1 hour each time the
button is pressed, until h24
appears on the display, at
which point pressing the
button again will reset the
delay start to zero.
Confirm by pressing the
“START/PAUSE” button (the
light on the display starts to
flash). The countdown will
begin and when it has
finished the programme will
start automatically.
It is possible to cancel the
delay start by taking the
following action:
Press and hold the button for
5 seconds until the display will
show the settings for the
programme selected.
At this stage it is possible to
start the programme
previously selected by
pressing the “START/PAUSE”
button or to cancel the
process by setting the
selector to the OFF position
and then selecting another
programme.
EN
F
TECLA “INICIO DIFERIDO”
Esta tecla permite programar el
inicio del ciclo de lavado con
un retraso máximo de 24h.
Para programar el inicio
retardado, proceder del
siguiente modo:
Seleccionar el programa
deseado.
Pulsar el interruptor una primera
vez para activarlo (en el display
se visualizará la leyenda 00h) y
pulsar nuevamente para
programar un retraso de 1 hora
(en el display se visualizará la
leyenda 01h). Pulsándolo
sucesivamente, el retraso
programado aumenta a razón
de 1 hora hasta un máximo de
24h, mientras que
presionándolo nuevamente se
vuelve a poner a cero el inicio
retardado.
Confirmar pulsando la tecla
“INICIO/PAUSA” (el indicador
del display empezará a
parpadear) para iniciar la
cuenta, al final de la cual el
programa se iniciará
automáticamente.
Es posible cancelar el inicio
retardado mediante la
siguiente operación:
Mantener pulsada la tecla
durante 5 segundos hasta que
se visualicen en el display los
parámetros del programa
elegido.
En este punto es posible iniciar
con antelación el programa
elegido pulsando la tecla
“INICIO/PAUSA” o cancelar la
operación llevando el selector
a la posición OFF y
seleccionando sucesivamente
otro programa.
ES