Summary of PL 604
Page 1
1 93786156 g b instruction for the installation and operation of the electric hob ~~~ pl 604.
Page 2: Contents
2 unpacking the appliance .......................................................................... 3 recommendations .................................................................................... 3 • installation safety instructions ..............................................................
Page 3: Unpacking The Appliance
3 unpacking the appliance inside the appliance you will find a plastic bag containing the fixing brackets to install the hob in the worktop. Please read the following carefully in order to get the best from your appliance. Please keep the operating and installation instructions in a safe place for f...
Page 4: Installation
4 installation installing a domestic appliance can be a complicated operation which, if not carried out correctly, can seriously affect consumer safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in accordance with the technica...
Page 5
5 to proceed to the new connection, you mus adhere the following instructions • before making the connection, make sure that the installation is protected by a suitable fuse, see table on next page, and that it is fitted with wires of a large enough section to supply the appliance normally. 1 - oper...
Page 6: "electrical Connection"
6 installation: "electrical connection" 1rst phase shunt 1 - 2 shunt 2 - 3 2nd phase shunt 4 - 5 earth 1rst phase shunt 1 - 2 shunt 2 - 3 neutral shunt 4 - 5 earth 1rst phase shunt 1 - 2 2nd phase shunt 3 - 4 3rd phase 5 earth 1rst phase 1 2nd phase 2 3rd phase 3 neutral shunt 4 - 5 earth for the co...
Page 7: "building-In"
7 installation: "building-in" both the unit into which the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower part of the casing is adjacent to an area normally accessible when...
Page 8: "building-In"
8 the body of the hob is fitted with 4 location holes to take the fixing brackets that secure the intended to fix the hob in the unit. Place the 4 fixing brackets in such a way that the hob surface is placed perfectly in the support unit. Location for fixing brackets installation: "building-in" fixi...
Page 9: Pl 604
9 overall dimensions (cm) : width : 59 depth : 51 building-in dimensions (cm) - (see chapter "installation") width : 56 depth : 4 8 total electrical power : 7 kw in order to improve the quality of the products, candy may carry out modifications linked to technical improvements. Appliance meeting wit...
Page 10
1 0 the hot plate the rapid self-protecting electric hot plate this is a cast-iron hot plate, controlled by a 7 position switch. As with the previous hot plate, each position corresponds to a permanent and progressive temperature according to the marks 1, 2, 3, 4, 5 and 6. An internal thermostat cut...
Page 11
1 1 cooking with the electric hot plate to gest the best results from your appliance it is important to observe the following : • use thick, flat-bottomed cooking vessels, a completely flat bottom prevents the overheating of some points which cause food to stick. Thick metal allows for good heat dis...
Page 12: • General Maintenance
1 2 maintenance before all cleaning or dismantling operation, it is imperative to : . Disconnect the hob to the mains supply. . Let all parts of the hob cool down. Never use : . Harsh abrasives, scouring pads or sharp object to clean the hob. • general maintenance the enamelled hob . Enamelled steel...
Page 13
1 3 sa des usines de rosieres - 30, rue y. Lacelle - rosières - 18400 lunery rcs bourges b 553 720 053 - capital de 18 000 000 f tél. 02.48.55.78.00 - télex 780868f - fax 02.48.68.01.75.