Cannon this heater is approved for use with natural and propane gases. Please leave instructions with the owner canterbury inbuilt models user instructions installation instructions service instructions 24 part no: f2901 revision e- 2009 cannon for service to this appliance for service to this appli...
2 contents contents 2 warranty 3 ❍ distributor safety warnings 4-5 ❍ what to do if you smell gas ❍ warnings ❍ standards user instructions 6-8 ❍ operating instructions ❍ cleaning ❍ flame characteristics heater specifications 9 installation instructions 10-15 ❍ clearances ❍ installation into a masonry...
3 the cannon appliance is warranted against defects in materials and work- manship for a period of one, (1) year from its date of original purchase, for residential use in australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available thro...
4 please read this manual before installing and using the heater. What to do if you smell gas 1. Turn off the main gas supply. 2. Extinguish any open flame. 3. Open windows. 4. Do not touch electrical switches. 5. Do not use your telephone. 6. Call your gas supplier immediately from a neighbour’s ph...
5 8. If removed, the glass window must be put back onto the unit prior to operating the heater. 9. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number. 10. For installation into a non-combustible fireplace, i.E.: masonry or bri...
6 operating instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. 2. For control lay-out refer to figure 2 3. To turn heater on press switch to power on position. There is a 5 second delay before the burner i...
7 5. To increase the fan speed to med, press switch for med setting. Refer figure 5. 6. To increase the fan speed to high, press switch for high setting. Refer figure 6. 7. To turn the burner to low setting, press switch for low setting. Refer figure 7. On low burner setting it is more efficient to ...
8 cleaning all cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. For heater fitte...
9 gas type: natural or propane gas, as indicated on data label gas consumption: 26 mj/hr input energy output: 21.45 mj/hr (5.96 kw) energy star rating: 4 stars heater type: approved to as4553:2008 operating pressure: natural gas: 0.75 kpa (at the burner) propane gas: 2.65 kpa gas regulator: integral...
10 1. This appliance is to be installed by a licensed service person only. 2. This appliance shall be installed in accordance with the manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, and as5601 the australian stand- ar...
11 refer as5601. For “air movement not to affect appliance” see clause 5.3.1. For ‘air supply to appliance’ see clause 5.4.1. For ‘ventilation requirements’ see clause .5.4.3. 11 installation with a flue connected 14 11. Remove the inner glass. Slacken off screws in top clamp and remove side clamps....
12 installation without a flue connection. 12 13 13 6. Prepare electrical and gas connections. Remove the lower front cover, see figure 16. A 10 amp wall socket needs to be located within 1.5m of the heater. If using a power point in the chimney, route the plug and cord through cord access at lower ...
12 installation without a flue connection. 12 13 13 6. Prepare electrical and gas connections. Remove the lower front cover, see figure 16. A 10 amp wall socket needs to be located within 1.5m of the heater. If using a power point in the chimney, route the plug and cord through cord access at lower ...
11 refer as5601. For “air movement not to affect appliance” see clause 5.3.1. For ‘air supply to appliance’ see clause 5.4.1. For ‘ventilation requirements’ see clause .5.4.3. 11 installation with a flue connected 14 11. Remove the inner glass. Slacken off screws in top clamp and remove side clamps....
10 1. This appliance is to be installed by a licensed service person only. 2. This appliance shall be installed in accordance with the manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, and as5601 the australian stand- ar...
9 gas type: natural or propane gas, as indicated on data label gas consumption: 26 mj/hr input energy output: 21.45 mj/hr (5.96 kw) energy star rating: 4 stars heater type: approved to as4553:2008 operating pressure: natural gas: 0.75 kpa (at the burner) propane gas: 2.65 kpa gas regulator: integral...
8 cleaning all cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. For heater fitte...
7 5. To increase the fan speed to med, press switch for med setting. Refer figure 5. 6. To increase the fan speed to high, press switch for high setting. Refer figure 6. 7. To turn the burner to low setting, press switch for low setting. Refer figure 7. On low burner setting it is more efficient to ...
6 operating instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. 2. For control lay-out refer to figure 2 3. To turn heater on press switch to power on position. There is a 5 second delay before the burner i...
5 8. If removed, the glass window must be put back onto the unit prior to operating the heater. 9. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number. 10. For installation into a non-combustible fireplace, i.E.: masonry or bri...
4 please read this manual before installing and using the heater. What to do if you smell gas 1. Turn off the main gas supply. 2. Extinguish any open flame. 3. Open windows. 4. Do not touch electrical switches. 5. Do not use your telephone. 6. Call your gas supplier immediately from a neighbour’s ph...
3 the cannon appliance is warranted against defects in materials and work- manship for a period of one, (1) year from its date of original purchase, for residential use in australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available thro...
2 contents contents 2 warranty 3 ❍ distributor safety warnings 4-5 ❍ what to do if you smell gas ❍ warnings ❍ standards user instructions 6-8 ❍ operating instructions ❍ cleaning ❍ flame characteristics heater specifications 9 installation instructions 10-15 ❍ clearances ❍ installation into a masonry...
Cannon this heater is approved for use with natural and propane gases. Please leave instructions with the owner canterbury inbuilt models user instructions installation instructions service instructions 24 part no: f2901 revision e- 2009 cannon for service to this appliance for service to this appli...