Use, care and installation instructions for your new cannon wood heater model no. Cawdfs12 installer: please ensure these instructions remain with the owner. Prior to operating your brand new wood heater thoroughly read and understand these instructions. Warning: improper installation, adjustment, a...
Product specifications unit net weight : 120kg heat output : 12kw heating efficiency : 62% particulate emissions : 1.7g/kg heating capacity : up to 22 squares (205 m2) overall dimensions : (h) 760mm x (w) 680mm x (d) 609mm (does not include handle) plinth dimensions : (h) 20mm x (w) 658mm x (d) 540m...
Cautions : read this first your cannon wood heater has been designed and tested to rigorous australian standards, and will provide you with beautiful, environmentally sustainable home heating for many years. However, we must remember that these appliances are very powerful, and need to be both insta...
Cautions model no – cawdfs12 if the power supply cord is damaged, it must be replaced by the manufacturer, its service agent or a suitably qualified person in order to avoid electrical hazard. Install strictly according to these instructions this heater and flue system must be installed in accordanc...
Installation this heater and flue system must be installed in accordance with the latest version of as/nzs 2918, relevant building and local government regulations, using the clearances and requirements outlined in these instructions. Note: you may need to obtain local government approval prior to i...
Installation model no – cawdfs12 flue requirements your cannon wood heater must be installed with an approved “default” flue kit available from your retailer. You must not modify the kit in any way or mix components from other kits. One of the most important factors that determine the performance of...
Installation model no – cawdfs12 page 6 clearances it is mandatory that the heater is installed sufficiently clear of combustible material. See the diagram and table below for minimum clearances for both parallel to the wall and corner installation configurations. Warning: failure to observe these c...
Installation model no – cawdfs12 final assemby assembly of your cannon wood heater is very straightforward, as most of the work has been done for you at our factory. Set up the fire bricks place the bricks upright as shown in the illustration. - 3 across the back, and 2 on each side. Position the br...
Using your heater model no – cawdfs12 page 8 the importance of seasoned hardwood in our experience, there is very little difference between different types of hardwood (eg box gums, stringy bark etc). What is far more important is how well the wood is seasoned. When wood is first cut down, it has a ...
Using your heater model no – cawdfs12 creating the perfect fire the golden rule in the early stages of a fire, smaller wood pieces and more air flow is the key. Bigger pieces of wood absorb more heat before they start to burn, so they tend to lower the temperature of the firebox. This is why you sho...
Using your heater model no – cawdfs12 page 10 other useful tips overnight burns to set up for an overnight burn, ensure there is a hot bed of coals to begin. Load up with large logs, and turn the air control to high until the fire is burning strongly. Then move the air control down to low. To restar...
Care and maintenance model no – cawdfs12 cleaning all cleaning should be done when the heater has completely cooled. This should be done in the beginning of winter and once or twice during the season, depending on heater usage. With higher usage, cleaning more often is advised. Excess ashes should b...
Care and maintenance model no – cawdfs12 page 12 maintenance at the beginning of each winter season, you should check the following to ensure proper running of your heater. Any worn or cracked parts should be replaced immediately using replacement parts specified by the manufacturer. • door glass • ...
Wood heater limited warranty model no – cawdfs12 1. This warranty against defects for your newly purchased cannon product is proudly prepared by sampford ixl pty ltd of 1/391 boundary road, truganina, vic 3029, phone 1300 727 421. Sampford ixl products come with guarantees that do not exclude the fo...
Care and maintenance model no – cawdfs12 page 14 c. Will not apply where the defect in or failure of the product is attributable to misuse, abuse, accident or non-observation of the manufacturer’s instructions. This product must be used in accordance with the manufacturer’s instructions; d. Will not...
1/391 boundary road truganina vic 3029 model no – cawdfs12 t 1300 727 421 f 1300 727 425 e service@ixl.Com.Au w cannonappliances.Com.Au.
