Cannon Fitzroy Inbuilt Power Flue Instruction Manual - page 3
Cannon Fitzroy Inbuilt Power Flue | 3
8. If removed, the glass window must be put back onto
the unit prior to operating the heater.
9. Installation and repairs should be performed by a
licensed service person only, refer to back of brochure
for service number.
10. For installation into a non-combustible fireplace, i.e
masonry or brick or into a mock fireplace, i.e. timber
or plasterboard, the chimney and base should be
of sound construction.
Note: when installing into a mock fireplace a
mock fireplace installation kit must be used.
11. testing the effectiveness of the flue. before testing the
flue confirm air vents are unobstructed. If an exhaust
fan or other heating appliances are present switch
them on. this is to test that there is no interaction
between the Cannon heater and other appliances.
Refer to Australian Standard Gas Installations AS 5601.
For ‘air movement not to affect appliance’ see clause 5.3.1.
For ‘air supply to appliance’ see clause 5.4.1.
For ‘ventilation requirements’ see clause 5.4.3.
12. the appliance should be inspected prior to use,
with regular inspections (annually) to be made by a
licensed service person. It is important that circulating
air passageways of the appliance be kept clean, dirt
and lint free, for a safe and efficient operation of
the heater.
13. On first lighting your heater a smell may occur due to
its new condition. this is quite normal and will disap-
pear after a few hours use at the maximum
control position.
Important: When this heater is operating the mesh
guard/glass front is hot. The mesh guard, or glass
front is fitted to this appliance to reduce the risk of
fire or injury from burns and no part of it should be
permanently removed. For protection of young chil-
dren or the infirm, a secondary guard is required.
this appliance meets the following standards:
Standards australia
aS/nzS 3100
aS 5601
aS 4553:2008
safety warnings
Please read this manual before installing and using
the heater.
Safety Warnings
1. Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage.
refer to the sections of this manual for correct proce-
dures, or consult with place of purchase, a licensed
plumber, a gas supplier or the CannOn distributor
listed in this manual.
2. Install the heater only in locations that are referred to
in the installation instructions. Do not build the heater
into bookcases, walls or enclosures (combustible
materials) without the use of a Mock Fireplace kit.
3. Due to high temperatures the room heater should be
located out of traffic and away from:
Furniture and draperies
Combustible materials
gasoline and other flammable liquids
Do not place clothing or other flammable
material on or near the heater.
4. Keep curtains*, clothes, furniture and other
flammable materials at least 900mm from front
and sides of heater.
* at the owner’s discretion curtain clearance can
be less than 900mm as long as they are restrained
from the front, top and sides of the heater.
the manufacturer takes no responsibility if curtain
clearance is less than 900mm and not restrained.
5. Children and adults should be alerted to the hazard
of high surface temperature and should take care to
avoid burns or clothing ignition.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they have
been given supervision or instruction concern-
ing use of the appliance by a person responsible
for their safety. Children should be supervised to
ensure that they do not play with the appliance.
6. never attempt to burn paper or any other material in
the heater.
7.
Do not place articles on or against this appliance.
Do not use or store flammable materials near
this appliance.
Do not spray aerosols in the vicinity of this
appliance while it is in operation
Do not modify this appliance.