1. DL manuals
  2. Cannondale
  3. Bicycle
  4. Trigger 26ER
  5. Owner's Manual

Cannondale Trigger 26ER Owner's Manual

Manual is about: Cannondale Trigger Bicycle Owner’s Manual

Summary of Trigger 26ER

  • Page 1

    Cannondale usa cycling sports group, inc. 172 friendship road, bedford, pennsylvania, 15522-6600, usa (voice): 1-800-bike-usa (fax): 814-623-6173 custserv@cyclingsportsgroup.Com cannondale europe cycling sports group europe, b.V. Mail: postbus 5100 visits: hanzepoort 27 7570 gc, oldenzaal, netherlan...

  • Page 2: Warning

    This manual meets en standards 14764, 14766, and 14781. Vélo certifié conforme aux exigences du décret n 95-937 du 24 août 1995 norme nfr030 in this supplement, particularly important information is presented in the following ways: warning indicates a hazardous situation which, if not avoided, could...

  • Page 3: Safety Information

    22 safety information about this supplement cannondale owner’s manual supplements provide important model specific safety, maintenance, and technical information. They are not replacements for your cannondale bicycle owner’s manual. This supplement may be one of several for your bike. Be sure to obt...

  • Page 4: Inspection & Crash Damage of

    3 129920.Pdf 3 inspection & crash damage of carbon frames/forks warning after a crash or impact: inspect frame carefully for damage (see part ii, section d. Inspect for safety in your cannondale bicycle owner’s manual.) do not ride your bike if you see any sign of damage, such as broken, splintered,...

  • Page 5: Water Bottles

    44 water bottles side impacts to a water bottle or cage can result in damage threaded inserts due to the leverage on a very small area. In a crash, certainly the last thing you should be worried about is saving the threaded inserts in your frame. However, when you are storing or transporting your bi...

  • Page 6: Integrated Head Tube

    5 129920.Pdf 5 integrated head tube the following cannondale headset kits can be used : 45° up 45° down 12 mm - or - 1.125” kp119/ integrated headshok to 1.5 qsiseal/ upper bearing seal 58mm od hd169/ si headset bearings headshok 1.5” kp058/ integrated headshok to 1.1/8 notice cannondale headshok sy...

  • Page 7: Identification

    66 a 4 3 1 2 kf366/ kf368/ loctite™ 609 b kt010/ kt011/ 73mm 73mm 5 identification 1. Bottom bracket shell a. Bb circlip groove 2. Iscg03 mount b. Adapter drive-side groove 3. Circlip 4. Bearing 5. 73mm adapter bottom bracket bb30 the bottom bracket shell is compatible with the bb30 standard. See ht...

  • Page 8: Bearing Maintenance

    7 129920.Pdf 7 bearing maintenance inspect bearing condition annually (at a minimum) and anytime the crankset assembly is disassembled or serviced. With the crankset removed, rotate the inner bearing race of both bearings; rotation should be smooth. No play or movement inside the shell. If the beari...

  • Page 9: Fox Dyad Rt2 Pull Shock

    88 1 8 13 9 9 16 17 7 2 4 3 5 14 18 . 5” 15 11 20 19 10 8 6 12 5-10 inlbs fox dyad rt2 pull shock the dyad rt2 rear shock was engineered and manufactured by fox racing shocks in collaboration with cannondale. This supplement includes safety information, and instructions on how to set-up and operate ...

  • Page 10: Warning

    9 129920.Pdf 9 maintenance & service information warning high-pressure hazard - do not open, disassemble, modify, or attempt to perform internal service to the shock. The dyad rt2 shock is not user serviceable. Never attempt to remove the spool chamber end caps for any reason! Attempting to perform ...

  • Page 11: Setting Sag:

    10 10 flow mode (long travel) 120/130 mm fwd elevate mode (short travel) 70/80 mm setting sag: 1. Set shock to the 120/130 mm (long travel) mode with the remote lever. In this mode, the sag you set will be 100%. 2. When the dyad rt2 is switched to the 70/80 mm mode, the sag is automatically reduced ...

  • Page 12: Notice

    11 129920.Pdf 11 notice to prevent damage to the shock: 1. Follow the setting sag step in order. 2. Follow/maintain high and low pressure limits. 3. Make sure the suspension pump and dyad rt2 valves are clean before attachment. Warning use only high-pressure air pump – cannondale – 1mp01/slv to set ...

  • Page 13: Setting Rebound

    12 12 setting rebound rebound controls the rate at which your rear wheel returns after it has been compressed. The proper rebound setting is of personal preference, and varies with rider weight, riding style and conditions. A basic rule of thumb is to set rebound to be as quick as possible, without ...

  • Page 14: Dyad - Remote Lever

    13 129920.Pdf 13 dyad - remote lever the handlebar remote lever is used to change dyad between travel modes. Press the lever button to release the locking mechanism. The travel positions are shown below. Trigger 29’er - 80 mm trigger 26’er - 70 mm trigger 29’er - 130 mm trigger 26’er - 120 mm.

  • Page 15: Remote Cable Installation

    14 14 remote cable installation attach remote cable with shock unmounted from frame. 1. Place bike in a work stand with the rear wheel supported so the linkage does not move and the shock can be positioned and reconnected. 2. Determine cable housing length. Allow sufficient slack for proper shock op...

  • Page 16

    15 129920.Pdf 15 left handlebar right handlebar 8. Install the dyad rt2 back into the bicycle frame. Clean the mounting bolt threads, apply loctite 242 (blue) and tighten to 8.0 nm, 71 inlbs. 9. Secure the housing to the dt frame guide. 10. Test the lever for normal operation between the 120/130 mm ...

  • Page 17: Notice

    16 16 35 mm 5 m m 4 m m 1 2 13 14 12 13 1 600mm sram 650mm shimano 155mm note orientation of dt clamps. Small plate should be positioned under the housing (parallel with lines) with the rounded sides up as shown. It is not side-specifi c, however. Notice incorrect clamp placement can result in damag...

  • Page 18: Main Pivot

    17 129920.Pdf 17 always loosen the pinch bolts first. Before assembly, inspect all bearings for good condition. Replace if necessary. Always clean and apply loctite 242 (blue) to the pinch bolt threads. Always tighten with a torque wrench to 5 nm, 44 inlbs. Main pivot notice incorrect installation s...

  • Page 19: About This Supplement

    18 18 about this supplement this supplement includes information for the proper installation and set up of xfusion shocks in the following cannondale models: trigger 29’er alloy and both jekyll and scarlet. In addition to this supplement, follow the owner’s manual supplement infor- mation for your s...

  • Page 20

    19 129920.Pdf 19 rebound dial damping remote negative air valve max pressure: 175 psi, 12 bar positive air valve max pressure: 475 psi, 33 bar shock mounting bolt 8.0 nm (71 inlbs) loctite 242 (blue) shock mounting bolt 8.0 nm (71 inlbs) loctite 242 (blue) remote cable front of bike.

  • Page 21

    20 20 press the small top button to release the lever. When the remote lever is up, the shock is open. Press the remote lever down until it locks to change the shock to firm. The handlebar remote changes the shock performance between “open” and “firm”. See the illustrations below. Xfusion pull shock...

  • Page 22: Trigger 26 Carbon (Us Only)

    21 129920.Pdf 21 trigger 29’er alloy recommended sag: 25% (32 mm ) use the table below to set intial air pressure(s) accord- ing to rider weight; measure sag, then add or release air pressure in small amounts to set sag. Xfusion shock info: cannondale p/n travel eye-to-eye bushing width 128870 130 m...

  • Page 23: Dropout - Trigger 26’Er

    22 22 6 8 1 m3x10 loctite 242 (blue) 2.5 nm (22 inlbs) 5mm loctite 242 (blue) 7 nm (62 inlbs) 5mm loctite 242 (blue) 10 nm (88.5 inlbs) 5 5 4 4 2 3 7 10 9 dropout - trigger 26’er identification 1. Seat stay 2. Left dropout 3. Right dropout 4. Pivot spacers 5. Pivot axle bolts 6. Rear derailleur hang...

  • Page 24: Identification

    23 129920.Pdf 25% 1 c d 2 4 b 7 d c 3 6 m6x30 6 m6x30 5mm loctite 242 (blue) 8 nm (71 inlbs) m5x16 5mm loctite 242 (blue) 5 nm (44 inlbs) 9 m5x16 7 9 5 kp169/ 8 5mm loctite 242 (blue) 8 nm (71 inlbs) 23 23 shock link - trigger 26’er identification 1. Shock link 2. Link pivot 3. Ss pivot 4. Main shim...

  • Page 25: Trigger 26’Er

    24 kp252/ a b b kp175/ kp176/ kp177/ kp178/ kp187/ kp240/ a a b a m6x30 kp181/ m6x30 kp238/ m5x16 m5x16 m5x20 m5x20 m5x12 1mp01/slv kp169/ kp121/ kp237/ kp180/ code description kp121/ kit, der. Hanger kp175/ kit, adapter, si12 pm/160 kp176/ kit, adapter, si12 pm/180 kp177/ kit, adapter, si12 pm/185 ...

  • Page 26: Trigger 26’Er

    25 129920.Pdf kp236/* kp054/ b b qsiseal/ 12 mm kf103/ kp058/ kp119/ kp182/ qc616/ kp018/ kb6180/ kf368/ kp189/ kp170/blk kp170/red 73mm kf115/ hd169/ headshok 1 1/8” 1.5” bhcs m5x16 fhcs m4x16 fhcs m4x8 shcs m5x12 kp205/ taper code description kp170/blk, red kit, seatbinder, mtn qr, 34.9, blk kp182...

  • Page 27: Geometry

    26 26 a b k p h i j f l m f g e c o astm condition 3 xc racing astm f2043 for rough off-road riding and jumps less than 24” (61 cm) geometry / specifications - trigger 26’er geometry sizes (cm/in) s m l xl a seat tube length 43.2/17.0 45.7/18.0 48.3/19.0 50.8/20.0 b top tube horizontal 55.7/21.9 58....

  • Page 28: Specifications

    27 129920.Pdf 27 specifications frame material ballistec carbon travel w/ dyad rt2 (120 mm, 70 mm) / w/ xfusion (120 mm) headtube headshok, 1.5in, 1.125in (see replacement parts for kit info.) chainline 50 mm bb shell width bb30 73 mm seat post diameter use a seat post with a 31.6 mm diameter only. ...

  • Page 29: Dropout - Trigger 29’Er

    28 28 4 7 3 4 10 9 2 8 1 5 m4x8 m4x16 m4x13 m4x13 6 5mm loctite 242 (blue) 7 nm (62 inlbs) 5mm loctite 242 (blue) 10 nm (88.5 inlbs) 5mm loctite 242 (blue) 7 nm (62 inlbs) loctite 242 (blue) 2.5 nm (22 inlbs) 12 11 dropout - trigger 29’er identification 1. Seat stay 2. Left dropout 3. Right dropout ...

  • Page 30: Identification

    29 129920.Pdf 5mm loctite 242 (blue) 7 nm (62 inlbs) 1 c d 2 3 a b 6 5 5 m8x30 m5x16 8 5mm loctite 242 (blue) 5 nm (44 inlbs) 5 5mm loctite 242 (blue) 8 nm (71 inlbs) 7 4 kp169/ 12 11 9 c 3 b b d c 3 b b d 29 shock link - trigger 29’er identification 1. Shock link 2. Link pivot 3. Main shim 4. Link ...

  • Page 31: Trigger 29’Er

    30 code description kp173/ kit,der.Hanger;si12 kp174/ kit,spacer,si12,142 to 135mm kp175/ kit,adapter,si12 pm/160 kp176/ kit,adapter,si12 pm/180 kp177/ kit,adapter,si12 pm/185 kp178/ kit,adapter,si12 pm/203 kp190/ kit,axle,syntace,x12,142x12mm kp291/ kit,spacer,f.Der,trigger29 kp183/ kit,zip ties, c...

  • Page 32: Trigger 29’Er

    31 129920.Pdf code description kp170/grn kit,seatbinder,mtn qr,34.9,blk kp290/ kit,guide,housing,bolt kp291/ kit,spacer,f.Der,trigger29 kf103/ kit,guard,scuffguard-8pk kh118/097ht kit,steer,supermax, 1.5” kh118/109ht kit,steer,supermax, 1.5” kh118/122ht kit,steer,supermax, 1.5” kh118/134ht kit,steer...

  • Page 33: Geometry

    32 32 m h n f b p i d e’ k l j a o c e astm f2043 for extreme off-road riding astm condition 4 all-mountain g geometry sizes (cm/in) small medium large x-large a seat tube length 42.5/16.7 44.5/17.5 48.5/19.1 50.9/20.0 b top tube horizontal 56.8/22.4 59.6/23.5 62.4/24.6 65.2/25.7 c top tube actual 5...

  • Page 34: Specifications

    33 129920.Pdf 33 specifications frame material smartformed alloy travel w/ dyad rt2 (130 mm, 80 mm) / w/ xfusion (130 mm) headtube headshok, 1.5in, 1.125in (see replacement parts for kit info.) chainline 50 mm bb shell width bb30 73 mm chainguide mount iscg 03 seat post diameter use a seat post with...

  • Page 35

    34 4 2 5 3 1 3 3 1 5 1 4 5 2 4 2 5 3 1 3 3 1 5 1 4 5 2 34 cable routing - trigger 29’er 1. Rear derailleur 2. Front derailleur 3. Rear brake 4. Shock remote 5. Seat post remote.

  • Page 36

    35 129920.Pdf 35.

  • Page 37: Maintenance

    36 36 maintenance the following table lists only supplemental maintenance items. Please consult your cannondale bicycle owner’s manual for more information on basic bike maintenance. Consult with your cannondale dealer to create a complete maintenance program for your riding style, components, and c...

  • Page 38

    Cannondale usa cycling sports group, inc. 172 friendship road, bedford, pennsylvania, 15522-6600, usa (voice): 1-800-bike-usa (fax): 814-623-6173 custserv@cyclingsportsgroup.Com cannondale europe cycling sports group europe, b.V. Mail: postbus 5100 visits: hanzepoort 27 7570 gc, oldenzaal, netherlan...