- DL manuals
- Canon
- Printer
- 1450B002 - PIXMA MP510 All-in-One Photo Printer
- Quick Start Manual
Canon 1450B002 - PIXMA MP510 All-in-One Photo Printer Quick Start Manual - page 69
65
Troubleshooting
Printing on inappropriate type of paper.
z
Check to see if the paper you are printing on is not too thick or curled.
See “Media Types You Cannot Use” on page 7.
z
When performing Borderless Printing, print quality may be reduced at the top
and bottom edges of the paper. Make sure that the paper you are using is
suitable for Borderless Printing.
For details, refer to the Printer Driver Guide on-screen manual.
Paper is curled.
If you are using paper with either any of the corners or the whole printing
surface curled, the paper may become dirty, not feed properly, or both. Use such
paper after correcting paper curl as follows.
(1)With the printing side (A) facing up, cover the paper with a fresh sheet of
plain paper to avoid staining or scratching the surface.
(2)Roll up the paper in a direction opposite to paper curl as seen below.
(3)Check to see that the paper curl is corrected to within approximately 0.08 to
0.2 inches / 2 to 5 mm (B) in height.
We recommend printing curl-corrected paper one sheet at a time.
Inappropriate Paper Thickness Lever
setting.
Adjust the position of the Paper Thickness Lever according to the type of paper
you are printing on. See “Loading Printing Paper” on page 6.
Depending on the printing content, the printing surface may become scratched
even for the types of paper to set the lever to the left. In this case, set the Paper
Thickness Lever to the right.
* Reset the Paper Thickness Lever to the left when you finish printing. If the
lever is not set back to the left, the inside of the machine is more likely to get
dirty due to the wider clearance between the print head and the loaded paper. It
may also reduce print quality.
Media Type setting in the Operation
Panel does not match the actual type of
paper.
Check that the Media Type set in the Operation Panel (when performing
wireless printing, the Media Type setting in Wireless print settings) matches
the type of the loaded printing paper.
See “Changing the Print Settings” on page 17.
Printing graphics with Intensity setting
set too high.
Especially if you are using plain paper to print images with high intensity, the
paper may absorb too much ink and become wavy, causing paper abrasion. In
this case, reduce the Intensity setting in the Operation Panel and try printing
again.
Printing beyond the recommended
printing area.
If you are printing beyond the recommended printing area of your printing paper,
the lower edge of the paper may become stained with ink.
Resize your original document in your application software.
For details on recommended printing area, refer to “Printing Area” in the User’s
Guide on-screen manual.
Cause
Action
(A)
(1)
(2)
(B)
(A)
Summary of 1450B002 - PIXMA MP510 All-in-One Photo Printer
Page 1
Photo all-in-one quick start guide canon u.S.A., inc. One canon plaza, lake success, ny 11042, u.S.A. Canon inc. 30-2, shimomaruko 3-chome, ohta-ku, tokyo 146-8501, japan canon canada, inc. 6390 dixie road, mississauga, ontario, l5t 1p7, canada canon latin america, inc. 703 waterford way, suite 400,...
Page 2
Getting help from canon help us help you better before you contact canon, please record the following information. Serial number (located on the inside of the product):_________________________________________ model number (located on the front of the product): ______________________________________...
Page 3
Photo all-in-one quick start guide.
Page 4
Canon pixma mp510 photo all-in-one quick start guide. Copyright this manual is copyrighted by canon u.S.A., inc. With all rights reserved. Under the copyright laws, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of canon u.S.A., inc. © 2006 cano...
Page 5
Table of contents 1 before printing................................................2 turning the machine on and off ....................2 handling the original document.....................4 loading printing paper ...................................6 changing the print settings ........................
Page 6
2 before printing before printing turning the machine on and off turn on the machine before printing. Turning on the machine before turning on the machine, confirm the following. Z the print head and ink tanks are set into place. If you are using the machine connected to a computer, confirm also the...
Page 7
3 before printing turning off the machine 1 to turn off the machine, press the on/off button. When the power lamp stops flashing, the machine is turned off. Z the screen-saver mode the lcd goes out if the machine is not operated for 5 minutes. Press any button to restore the display. You cannot chan...
Page 8
4 before printing handling the original document this section describes how to load the original document on the platen glass. Original document requirements the original documents you load on the platen glass for copying or scanning must meet these requirements: loading original documents load orig...
Page 9
5 before printing 2 gently close the document cover. Important z do not place any objects weighing more than 4.4 lb / 2 kg on the platen glass. Z do not press or put weight on the original with pressure exceeding 4.4 lb / 2 kg. Doing so may cause the scanner to malfunction or the platen glass to bre...
Page 10
6 before printing loading printing paper this section describes how to load printing paper in the auto sheet feeder and the front feeder. Paper handling z recommended paper and requirements media type model *1 paper support load limit paper thickness lever printer driver setting for media type auto ...
Page 11
7 before printing paper with a model number is canon specialty media. You may not be able to purchase some canon genuine papers depending on your country. *1 paper is not sold in the us by model number. Purchase paper by name. *2 available only when printing from your computer. *3 feeding this paper...
Page 12
8 before printing z postcards affixed with photos or stickers z envelopes with double flaps z envelopes with sticker flaps z envelopes with an embossed or treated surface z any type of paper with holes z paper that is not rectangular z paper bound with staples or glue z paper with adhesives z paper ...
Page 13
9 before printing using the auto sheet feeder and the front feeder this machine offers two paper sources to load printing paper; the auto sheet feeder, found at the top of the machine, and the front feeder, found at the front of the machine. (a) auto sheet feeder (b) front feeder z when printing for...
Page 14
10 before printing z to change the paper source the auto sheet feeder lamp lights up when feeding from the auto sheet feeder, and the front feeder lamp lights up when feeding from the front feeder. Before you print, make sure that the paper source selection matches the paper source where you actuall...
Page 15
11 before printing changing the paper source before printing, confirm that the location where you have loaded paper is selected as the paper source. Press the paper feed switch to change the paper source. (a) auto sheet feeder lamp (b) paper feed switch (c) front feeder lamp important when printing ...
Page 16
12 before printing loading paper important z if you cut plain paper to 4" x 6" / 101.6 x 152.4 mm, 5" x 7" / 127.0 x 177.8 mm, or 2.13" x 3.39" / 54.0 x 86.0 mm (credit card-size) for a trial print, it can cause paper jams. Z you cannot print on postcards affixed with photos or stickers. Z always lo...
Page 17
13 before printing z loading paper in the auto sheet feeder 1 flatten the four corners of the paper before loading it. 2 prepare to load paper. (1) open the sheet feeder cover and pull out the paper support. (2) open the front feeder. (3) extend the paper output support. (4) press the paper feed swi...
Page 18
14 before printing 3 load the paper. (1) load the paper in the auto sheet feeder with the print side facing up. (2) align the paper stack against the cover guide on the right side of the paper support. (3) pinch the paper guide and slide it against the left side of the paper stack. Z loading paper i...
Page 19
15 before printing 3 load the paper with the print side facing down. (1) load the paper in the front feeder with the print side facing down and the leading edge to the far side. (2) align the paper stack against the right edge of the front feeder. (3) align the near and the left edges of the paper w...
Page 20
16 before printing loading envelopes envelopes must be fed from the auto sheet feeder. Use either european dl or us comm. Env. #10-sized envelope. 1 retract the paper support. 2 load the envelope against the cover guide (the right side of the paper support). Load with the front face up and the rear ...
Page 21
17 before printing changing the print settings this section describes the settings screen that can be specified on the operation panel when copying or when printing from a memory card. To change the print settings you can change the print settings such as page size, media type, bordered or borderles...
Page 22
18 before printing 4 change the setting. (1) use the [ or ] button to change the setting. Example: change to 4" x 6" (101 x 152) here. 5 complete setting. (1) press the settings button. The lcd returns to the settings screen. Print setting items each tab contains the following setting items. To chan...
Page 23
19 before printing (3) adjust image quality according to the original. Fast, standard, high (4) you can specify the reduction or enlargement method. Same magnification, preset ratio, zoom (25-400%), fit-to-page tab 2 you can specify auto intensity. (5) specify if auto intensity is performed. Auto in...
Page 24
20 before printing (1) select the page size. 8.5" x 11" (215 x 279), a4, 4" x 6" (101 x 152), 5" x 7" (127 x 177), credit card (2) select the media type. Plain paper, photo paper pro, photo plus glossy, matte photo paper, glossy photo paper (3) select the print quality. Standard, high (4) select bor...
Page 25
21 before printing (4) activate/deactivate face brightener function. Brightens a darkened face on the photo taken against the light. Face brightener on, face brightener off (5) activate/deactivate image optimizer function. Corrects and smooths the jagged contours for printing. Image optimizer on, im...
Page 26
22 printing from your computer printing from your computer this section describes the procedure for basic printing. Printing with windows 1 turn on the machine and load the paper in the machine. See “turning the machine on and off” on page 2 and “loading printing paper” on page 6. 2 make sure that t...
Page 27
23 printing from your computer printing with macintosh 1 turn on the machine and load the paper in the machine. See “turning the machine on and off” on page 2 and “loading printing paper” on page 6. 2 make sure that the proper paper source is selected. See “changing the paper source” on page 11. 3 c...
Page 28
24 scanning images scanning images you can scan images from the machine to a computer without printing them and save them in popular file formats, such as jpeg, tiff, bitmaps, or pdf. If you are scanning printed text, you can use the ocr (optical character recognition) software to convert it to text...
Page 29
25 copying copying making copies this section describes the basic procedure to make copies. 1 turn on the machine, and load the printing paper. See “turning the machine on and off” on page 2 and “loading printing paper” on page 6. 2 make sure that the proper paper source is selected. See “changing t...
Page 30
26 printing from a memory card printing from a memory card memory cards supported by this machine the following memory cards are compatible with this machine. *1 requires purchase of a separate compact flash card adapter for xd-picture cards. *2 use the special adapter provided with the card. Memory...
Page 31
27 printing from a memory card inserting the memory card 1 turn on the machine. See “turning the machine on and off” on page 2. 2 open the card slot cover. 3 insert one and only one memory card into the card slot. * be sure to attach the memory card to the special adapter before inserting it into th...
Page 32
28 printing from a memory card removing the memory card 1 open the card slot cover. 2 make sure that the access lamp is not flashing, then remove the memory card. 3 close the card slot cover. Printing photographs (single-photo print) 1 turn on the machine, and load printing paper. Load paper other t...
Page 33
29 printing from a memory card photo index print prints an index of all the photos saved on a memory card. Dpof print prints according to the digital print order format (dpof) settings on your digital camera, if you have specified them. Printing using the photo index sheet 1 turn on the machine, and...
Page 34
30 printing photographs directly from a compliant device printing photographs directly from a compliant device printing from a pictbridge compliant device you can connect a pictbridge compliant device such as a digital camera, camcorder, or mobile phone and print recorded images directly without usi...
Page 35
31 printing photographs directly from a compliant device (1) make sure that the pictbridge compliant device is turned off. (2) connect the pictbridge compliant device to the machine using a usb cable recommended by the manufacturer of the device. The device turns on automatically. If your device doe...
Page 36
32 printing photographs directly from a compliant device the following sizes and types of printing paper can be loaded according to the paper size and paper type settings. *1 exclusively used to print photo stickers. When printing on sticker paper, select 10x15 cm/4" x 6" in paper size. *2 can be se...
Page 37
33 printing photographs directly from a compliant device z date/file no. Print setting you cannot change this setting on this machine. The setting on the pictbridge compliant device is applied. If the images already have dates superimposed when shot, set this pictbridge setting item to off. If you s...
Page 38
34 routine maintenance routine maintenance replacing an ink tank when ink runs out, replace the ink tank. The machine will not print if the wrong type of ink tank is used, or if it is installed in the incorrect position. The machine uses the following ink tanks. Getting the ink level information you...
Page 39
35 routine maintenance knowing when to replace ink tank identify the empty ink tank on the lcd and replace it. If the “!” symbol is displayed above an ink tank if the machine detects low ink when you start printing, an error message such as the following appears on the lcd. Obtain a replacement tank...
Page 40
36 routine maintenance replacing ink tanks when ink tanks run out of ink, replace them using the following steps. 1 open the front feeder. 2 make sure that the machine is turned on, lift the scanning unit (printer cover) open, and set the scanning unit support to hold the cover. The print head holde...
Page 41
37 routine maintenance 4 prepare the replacement tank. (1) remove the new ink tank from its packaging, then pull the orange tape in the direction of the arrow (a) so that the protective film does not remain on the air hole (b). Then remove the film completely (c). (2) remove the orange protective ca...
Page 42
38 routine maintenance 5 install the ink tank. (1) insert the front end of the ink tank into the print head. (2) press on the mark on the ink tank until the ink tank snaps firmly into place. (3) make sure that the ink tank lamp lights up red. 6 lift the scanning unit (printer cover) slightly to set ...
Page 43
39 routine maintenance keeping the best printing results to avoid drying of the print head and clogging of the nozzles, note the following. When you turn off the machine follow the procedure below to turn off the machine. (1) press the on/off button to turn off the machine. (2) confirm that the powe...
Page 44
40 routine maintenance when printing becomes faint or colors are incorrect when printing becomes faint or colors are incorrect even if ink remains in the ink tanks, the print head nozzles are probably clogged. Print the nozzle check pattern to confirm the condition of the nozzles and then perform pr...
Page 45
41 routine maintenance printing the nozzle check pattern print the nozzle check pattern to determine whether the ink ejects properly from the print head. 1 make sure that the machine is turned on, open the front feeder, and extend the output paper support. 2 load a sheet of a4 or letter-sized plain ...
Page 46
42 routine maintenance examining the nozzle check pattern follow the procedure below to examine the nozzle check pattern, and perform cleaning if necessary. 1 check the nozzle check pattern you printed. (1) check if lines in this pattern are missing. (a) good (b) lines are missing (2) check if there...
Page 47
43 routine maintenance z if lines are missing or white streaks are present (1) select also b and press the ok button. The cleaning confirmation screen is displayed. (2) select yes and press the ok button to start print head cleaning. See “print head cleaning” on page 44. (1) (2).
Page 48
44 routine maintenance print head cleaning clean the print head if lines are missing or if white streaks appear in the printed nozzle check pattern. Cleaning unclogs the nozzles and restores the print head condition. Note that cleaning the print head causes used ink to be absorbed in the ink absorbe...
Page 49
45 routine maintenance note if the problem is not resolved after performing steps 4 and 5 twice, try print head deep cleaning. See “print head deep cleaning” on page 46..
Page 50
46 routine maintenance print head deep cleaning if print quality does not improve by standard print head cleaning, try print head deep cleaning, which is a more powerful process. Note that cleaning the print head causes used ink to be absorbed in the ink absorber. Print head deep cleaning consumes m...
Page 51
47 routine maintenance (3) if this does not solve the problem, the print head may be damaged. Contact your canon service representative..
Page 52
48 routine maintenance aligning the print head if ruled lines are printed misaligned or print results are otherwise unsatisfactory, adjust the print head position. Automatic print head alignment 1 make sure that the machine is turned on, open the front feeder, and extend the output paper support. 2 ...
Page 53
49 routine maintenance 5 adjust the print head position. (1) for each row in the print head alignment sheet (a, b, c, etc.), select the pattern that has the least noticeable streaks, and fill in the corresponding circle ( ) with a dark pencil or a black ink pen. (2) load the print head alignment she...
Page 54
50 routine maintenance 4 print the print head alignment sheet. (1) press the menu button. (2) use the [ or ] button to select maintenance/settings, then press the ok button. The maintenance/settings screen is displayed. (3) use the [ or ] button to select maintenance, then press the ok button. The m...
Page 55
51 routine maintenance (a) less noticeable white streaks (b) more noticeable white streaks (4) check the printed patterns and use the [ or ] button to input the number of the pattern in column l that has the least noticeable horizontal streaks. (5) when you have finished inputting all pattern number...
Page 56
52 routine maintenance cleaning your machine this section describes the cleaning procedure that is needed to maintain your machine. Cleaning the platen glass and document cover moisten a clean, soft, lint-free cloth and wring out excess water. With it, wipe the platen glass (a) and the inner side of...
Page 57
53 routine maintenance cleaning the paper feed rollers (roller cleaning) clean the paper feed rollers if paper is not fed properly. Z cleaning the paper feed rollers of the auto sheet feeder cleaning the paper feed rollers of the auto sheet feeder will wear the rollers, so perform this only when nec...
Page 58
54 routine maintenance 3 hold the rear cover lever and then press to the right and pull to remove the rear cover. 4 manually rotate the paper feed roller toward you and apply a cotton swab or the like to wipe off dust or stain. (a) do not touch these. (b) paper feed roller 5 reattach the rear cover....
Page 59
55 routine maintenance 4 load this and only this sheet of paper in the auto sheet feeder with the open side to the front. Set the paper thickness lever to the left. 5 perform bottom plate cleaning. (1) press the menu button. (2) use the [ or ] button to select maintenance/settings, then press the ok...
Page 60
56 troubleshooting troubleshooting this section describes troubleshooting tips for problems you may encounter when using the machine. Z “error message is displayed on the lcd” on page 57 z “lcd cannot be seen at all or is hard to see” on page 59 z “an unintended language is displayed on the lcd” on ...
Page 61
57 troubleshooting if an error occurs when the machine is connected to a computer when an error occurs in printing such as the machine is out of paper or paper is jammed, a troubleshooting message is displayed automatically. Take the appropriate action described in the message. The message may vary ...
Page 62
58 troubleshooting “print head is not installed. Install the print head.” “the type of print head is incorrect. Install the correct print head.” follow the directions given in the easy setup instructions to install the print head. If the print head is already installed, remove the print head once an...
Page 63
59 troubleshooting lcd cannot be seen at all or is hard to see an unintended language is displayed on the lcd cause action the display on the lcd is hard to see. If the contrast of the lcd is too strong or too weak, adjust it in the adjust contrast menu in the maintenance/settings. Refer to “changin...
Page 64
60 troubleshooting cannot install the mp drivers cause action unable to proceed beyond the printer connection screen. If you were unable to proceed beyond the printer connection screen, follow the procedure below to reinstall the mp drivers. (1)click cancel on the printer connection screen. (2)click...
Page 65
61 troubleshooting cannot connect to computer properly printing speed is slow / usb 2.0 hi-speed connection does not work “hi-speed usb device plugged into non-hi-speed usb hub” or “this device can perform faster” message is displayed (windows xp only) the setup cd-rom is defective. Click start, sel...
Page 66
62 troubleshooting print results not satisfactory cannot print to end of job part of the page is not printed colors are unclear cause action size of the print data is extremely large (windows xp/windows 2000 only). In windows xp and windows 2000, click print options on the page setup sheet. Then, se...
Page 67
63 troubleshooting ink does not come out/printing does not start/printing is blurred/ colors are wrong/straight lines are misaligned cause action ink tank is empty. Open the scanning unit (printer cover) and check the ink lamps. If an ink lamp is flashing red slowly at about 3-second intervals, ink ...
Page 68
64 troubleshooting white streaks printed paper curls or has ink blots printed surface is scratched/paper is smudged the media is loaded with the wrong side facing upwards. Many types of paper are made to be printed on only a particular side of the paper. Printing on the wrong side may cause unclear ...
Page 69
65 troubleshooting printing on inappropriate type of paper. Z check to see if the paper you are printing on is not too thick or curled. See “media types you cannot use” on page 7. Z when performing borderless printing, print quality may be reduced at the top and bottom edges of the paper. Make sure ...
Page 70
66 troubleshooting colors are uneven or streaked printing problems when copying cause action print quality is not set appropriately. In the operation panel, set print quality in the copy mode or memory card mode to high. Especially when printing a document that requires a lot of ink, increasing the ...
Page 71
67 troubleshooting printing does not start cause action the machine is not powered on./the power cord is not connected. Make sure that the power cord is securely plugged into the power connector of the machine. Plug the power cord all the way in, since it may be difficult to plug. Ink tank is empty....
Page 72
68 troubleshooting paper does not feed properly unnecessary print jobs are left in queue. / computer problems. Restarting your computer may solve the problem. If there are any unnecessary print jobs, follow the procedure below to delete them. (1)open the printer properties dialog box. Refer to “open...
Page 73
69 troubleshooting paper source selection is inappropriate. Z you cannot load paper other than a4, letter, or b5-sized plain paper in the front feeder. When using any other type of paper, load it in the auto sheet feeder. Z make sure that the proper paper source is selected. If not, change the paper...
Page 74
70 troubleshooting paper jams cause action paper jammed in the paper output slot, the auto sheet feeder, or the front feeder. Remove the paper following the procedure below. (1)slowly pull the paper out, either from the paper source or from the paper output slot, whichever is easier. (a) when printi...
Page 75
71 troubleshooting paper jammed inside the machine at the transport unit. Remove the paper following the procedure below. (1)hold the rear cover lever and then press to the right and pull to remove the rear cover. (2)if you can see the jammed paper, slowly pull the paper out. Z be careful not to tou...
Page 76
72 troubleshooting error message appears on the screen writing error/output error/communication error cause action the machine is not ready. Confirm that the power lamp is lit. If the power lamp is off, turn the machine on. While the power lamp is flashing green, the machine is initializing. Wait un...
Page 77
73 troubleshooting error no.: 300 is displayed error no.: 1700/1710 is displayed cause action the machine is not ready. Make sure that the machine is turned on, and that it is connected securely to the computer. If the power lamp is off, turn the machine on. While the power lamp is flashing green, t...
Page 78
74 troubleshooting error no.: 2001 is displayed cannot print properly from a digital camera the following are the possible errors that may occur when printing directly from a digital still camera or digital video camcorder*, and the actions to resolve them. * hereafter, the digital still cameras and...
Page 79
75 troubleshooting *1 to resume printing, you can also press the ok button on the machine instead of selecting continue on the camera. *2 the ink absorber absorbs ink used during cleaning, for example. If this message appears, you will need to call for servicing to replace the absorber and to check ...
Page 80
76 troubleshooting cannot print properly from a photo index sheet cause action “failed to scan photo index sheet.” is displayed. Z make sure the photo index sheet is set in the correct position and orientation on the platen glass. Z make sure the platen glass and the photo index sheet are not dirty....
Page 81
77 appendix appendix reading the on-screen manuals along with this quick start guide, on-screen manuals are also supplied with your machine. For detailed instructions on installing the on-screen manuals, refer to your setup sheet. You can view the on-screen manuals in the following way: to view the ...
Page 82
78 appendix specifications general specifications printing resolution (dpi) 4800 (horizontal)* x 1200 (vertical) * ink droplets can be placed with a pitch of 1/4800 inch at minimum. Print speed * * based on canon standard pattern. Print speed may vary depending on system configuration, software, doc...
Page 83
79 appendix copy specifications copy speed * based on canon standard pattern. Copy speed may vary depending on document complexity, copy mode, page coverage and the number of copies. Black & white: fast mode approx. 25 cpm color: fast mode approx. 17 cpm multiple copy 1 - 99 pages intensity adjustme...
Page 84
80 appendix *1 conform to the operating system’s requirement when it is higher than this. For updated compatibility, visit our website. *2 operation can only be guaranteed on a computer with built-in usb or usb 2.0 hi-speed port and pre-installed windows xp, 2000, me, 98, or mac os x v.10.2.8 - v.10...
Page 85
81 appendix menu items when you press the menu button, the settings button, or the photo index sheet button, the menu will be displayed on the lcd. Use the menu items to specify various settings of the machines’s functions and to perform machine maintenance. Note z maintenance and settings can be pe...
Page 86
82 appendix z memory card mode menu button single-photo print multi-photo print special photo print layout print sticker print print all photos photo index print dpof print maintenance/settings settings button page size media type print quality bordered/borderless date/file no. Vivid photo photo opt...
Page 87
83 safety precautions safety precautions please read the safety warnings and cautions provided in this manual to ensure that you use the machine safely. Do not attempt to use the machine in any way not described in this manual. Warning you may cause an electric shock, fire, or damage the machine if ...
Page 88
84 safety precautions maintaining the machine do not attempt to disassemble or modify the machine. There are no user serviceable parts inside the machine. The machine contains high-voltage components. Never attempt any maintenance procedure not described in this guide. Working around the machine do ...
Page 89
85 safety precautions working around the machine never put your hands or fingers in the machine while it is printing. Do not place any object on the machine. Do not place metal objects (paper clips, staples, etc.) or containers of flammable solvents (alcohol, thinners, etc.) on top of the machine. I...
Page 90
86 safety precautions legal limitations on use of your product and use of images it may be unlawful to make copies of, scan, print, or use reproductions of the following documents. The list provided is non-exhaustive. When in doubt, check with a legal representative in your jurisdiction. Z paper mon...
Page 91
87 safety precautions users in the u.S.A. Regulatory information fcc notice (u.S.A. Only) for 120v, 60hz model model number: k10281 this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) th...
Page 92
88 safety precautions this limited warranty shall only apply if the product is used in conjunction with compatible computers, peripheral equipment and software. Canon usa shall have no responsibility for such items except for compatible canon brand peripheral equipment covered by a separate warranty...
Page 93
89 safety precautions original purchaser of the product or the person for whom it was purchased as a gift, and states your exclusive remedy. Canon usa offers a range of customer technical support* options: z interactive troubleshooting, e-mail technical support, the latest driver downloads and answe...
Page 94
90 safety precautions ** instantexchange warranty service is subject to the availability of refurbished or new replacement units. Canon u.S.A., inc. One canon plaza lake success, ny 11042 usa ©2006 canon u.S.A., inc. Canon is a registered trademark of canon inc. In the united states and may also be ...
Page 95
91 index index a appendix 77 b before printing 2 c changing the print settings 17 copy mode 18 memory card mode 19 cleaning inside 54 platen glass and document cover 52 roller 53 cli-8c cyan 34 cli-8m magenta 34 cli-8y yellow 34 copying 25 i ink level information 34 l legal limitations on use of you...
Page 96
Copyright © 1990 the regents of the university of california. All rights reserved. Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other...
Page 97
Getting help from canon help us help you better before you contact canon, please record the following information. Serial number (located on the inside of the product):_________________________________________ model number (located on the front of the product): ______________________________________...
Page 98: Quick Start Guide
Photo all-in-one quick start guide the following ink tanks are compatible with this product. Qt5-0454-v02 xxxxxxxx ©canon inc.2006 printed in vietnam.