1. DL manuals
  2. Charmglow
  3. Grill
  4. 720-0677
  5. User Manual

Charmglow 720-0677 User Manual

Manual is about: STAINLESS STEEL LP GAS GRILL

Summary of 720-0677

  • Page 1

    Item / article / articulo # 296477 stainless steel lp gas grill model / modÈle / modelo # 720-0677 example only: serial # ________ mfg. Date ________ purchase date: _________ questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-323-5263...

  • Page 2

    2 safety information….…………………………………………………....………………...………...3 package contents list………………………………………………………………………..……..7 preparation……………….…………………. ……………………….…………….………………..9 assembly instructions…………………………………………………………….…..……..………9 installation instructions…………………………………………………………….....…….……...18 operatio...

  • Page 3

    3 safety information warning – hazards or unsafe practices which could result in severe personal injury or death. Caution – hazards or unsafe practices which could result in minor personal injury. Warning caution warning do not try lighting this appliance without first reading the “lighting instruct...

  • Page 4

    4 before lighting inspect the gas supply hoses prior to turning on the gas. If there is evidence of cuts, wear, or abrasion, it must be replaced prior to use. Only the pressure regulator and hose assembly supplied with the unit should be used. Never substitute regulators for those supplied with the ...

  • Page 5

    5 do not use indoors. Safety practices to avoid injury when properly cared for, your grill will provide safe, reliable service for many years. However, extreme care must be used as the grill produces intense heat that can increase accident potential. When using this appliance basic safety practices ...

  • Page 6

    6 do not use aluminum foil to line the grill racks or grill bottom. This can severely upset combustion airflow or trap excessive heat in the control area. For proper lighting and performance of the burners, keep the burner ports clean. It is necessary to clean them periodically for optimum performan...

  • Page 7

    7 package contents list a. Main cart grill-----------1pc. B. Side burner lid----------2 pcs. C. Bottle opener--------------1pc. D. Bottom panel ----------1pc . E. Swivel caster ------------2 pcs. F. Left side panel----------1pc. Warning electrical grounding instructions for electrical equipment– thi...

  • Page 8

    8 g. Right side panel----------1pc. H. Back panel---------------1pc. I. Charcoal grill firebox -----1pc. J. Charcoal grill lid----------1pc k. Crank handle --------------1pc. L. Charcoal tray ----------1pc . M. Small drawer ----------- 1pc. N. Big drawer -----------------1pc. O. Big drawer handle --...

  • Page 9

    9 pack description quantity aa 1/4-in. X 23-mm main lid screw 2 pcs. Bb 1/4-in. X 12-mm truss head screw 36 pcs. Cc 1/4-in. X 15-mm truss head screw 12 pcs. Dd 5/32-in. X 10-mm truss head screw 9 pcs. Ee 1/4-in. Nut 4 pcs. Ff 1/4-in. Flat washer 10 pc. Gg 1/4-in locking washer 44 pc. Hh 5/32-in lock...

  • Page 10

    10 2. Side burner lids assembly mount the two side burner lids (b) onto each side burner using eight 1/4-in. X 15-mm truss head screws (bb), eight 1/4-in. Locking washers (gg) and eight 1/4-in. Washer (ff) as shown in fig. 1. Note: two screws and two washers for each side of each lid. 3. Bottle open...

  • Page 11

    11 5. Side panel assembly use two 1/4-in. X 15-mm truss head screws (bb) and two 1/4- in. Locking washers (gg) to connect the bottom of the left side panel (f) to the bottom panel (d). Make the left side panel flush with the rear of bottom panel and tighten the screws as shown in fig. 5. Repeat for ...

  • Page 12

    12 7. Firebox assembly remove the firebox assembly (i) from the carton and carefully place onto the grill cart shown in fig. 8 note: take care when moving the firebox assembly as the bottom flanges can be bent ,which would misalign the holes. Attach the firebox assembly (i) to the grill cart using f...

  • Page 13

    13 8. Charcoal lid assembly take out the lid (j) from carton, then attach lid (j) to the firebox (i) using two 1/4-in. X 23- mm main lid screws (aa), 1/4-in. Flat washers (ff), 1/4-in. Lock washers and 1/4-in. Nut (ee) to keep this lid in place as shown in fig. 10. Note: secure all of the above scre...

  • Page 14

    14 use two 1/4-in. X 15mm truss head screws (bb) and two 1/4-in. Nuts (ee) to keep the charcoal firebox in place. (two screw holes are located in the top of left side charcoal grill firebox panel) as shown in fig. 12. Note: the top 2 screws of the firebox should be screwed from main firebox inside t...

  • Page 15

    15 12. Charcoal handle installation remove the charcoal handle (k) from the carton, then screw it into the hole on the charcoal door by turning the handle clockwise as shown in fig. 15. 13. Push bar installation take out the push bar (o) from carton, align it to the right top side panel of the charc...

  • Page 16

    16 use two 5/32-in. X 10mm truss head screw (aa) to keep the support piece in place as shown in fig. 18. Note: two screws for each bottom side of the push bar. 14. Side shelf tray installation remove the side shelf tray (p) from carton, and put it onto the push bar as shown in fig.19. 15. Lamp wire ...

  • Page 17

    17 16. Liquid propane tank tray assembly put the liquid propane tank tray (u) inside the bottom panel of the cart grill, then use four 5/32-in. X 10mm screws (aa) and 5/32-in. Locking washer (bb) to fix the tank tray as shown in fig. 21. Move the tank tray lock piece up to unlock the tank tray, then...

  • Page 18

    18 17. Battery installation unscrew the ignition button housing, insert the battery (ii) into the housing with the positive terminal (+) facing outward. Replace the ignition button housing after the battery has been installed as shown in fig. 24. 18. Liquid propane hook-up attach the regulator insid...

  • Page 19

    19 liquid propane cylinder requirements (20-lb cylinder) a dented or rusty liquid propane cylinder may be hazardous and should be checked by your supplier. Never use a cylinder with a damaged valve. The liquid propane cylinder must be constructed and marked in accordance with the specifications for ...

  • Page 20

    20 leak testing general although gas connections on the grill are leak tested prior to shipment, a complete leak test must be performed at the installation site. Before each use, check all gas connections for leaks using the procedures listed below. If the smell of gas is detected at any time, you s...

  • Page 21

    21 it is very important to keep your appliances clear and away from any combustible materials. Maintain at least 24 inches of clearances from sides and back and do not use under overhead combustible construction. Operating instructions general use of the grill each main burner is rated at 10,000 btu...

  • Page 22

    22 using the rear burner your grill is capable of performing back burner rotisserie cooking. Light the rear burner as described in the lighting instructions on page 22. Once lit, the rear burner will reach cooking temperature in about 1 minute. Rotisserie kits are sold as accessory items. Please fol...

  • Page 23

    23 warning when lighting, keep your face and hands as far away from the grill as possible. Caution when using a match to light the grill make sure to use the attached lighting rod. Caution remove the warming rack when using a match to light the rotisserie burner. To match light the grill if a burner...

  • Page 24

    24 searing main burner and side burner 1. If you have already attempted to light the searing main burner or side burner with the igniter, allow 5 minutes for any accumulated gas to dissipate. 2. Insert a match into the lighting rod as shown in fig.27. Ignite the match and insert through the cooking ...

  • Page 25

    25 halogen lights light operation instructions 1. Make sure the light power switch on the control panel is in the “off” position. 2. Connect power plug to properly grounded outlet. 3. Turn the light power switch to “on.” halogen bulb replacement 1. Make sure that the grill has cooled before changing...

  • Page 26

    26 6. Use a flathead screwdriver to loosen the four screws locking the bulb in place. Loosen but do not remove the bottom two screws under the light first. Then loosen but not remove the upper two screws above the light. 7. Pull out the light bulb and replace with a new bulb. Tighten the four screws...

  • Page 27

    27 bulb specification bulb type: halogen wattage: 10 watts per bulb voltage: 12 volts please contact customer service at 1-877-323-5263 for assistance on bulb replacement information. Gas conversion from lp to ng this grill is portable and configured for use with liquid propane (lp gas), which is de...

  • Page 28

    28 1．install the regulator hose (short hose) to the end of the regulator marked "out". Install the brass connector to the other end of the regulator marked "in." (if regulator, hose, and brass connector are pre- assembled, you may disregard this step.) 2．turn all knobs to off. Turn off lp gas supply...

  • Page 29

    29 6mm nut driver 1. Remove the warming rack, cooking grids, flame tamers from the firebox. Remove the main tube burners by removing the screw securing the burners near the back wall of the firebox and the screws near the front of the firebox that secure the igniter brackets to the burners. Gently l...

  • Page 30

    30 6 mm nut driver 1. Loosen the igniter wire screws, searing main burner brace screws, and back two screws securing searing side burners. 2. Take out the searing side burner from the firebox. Locate orifice on end of valve and remove by turning counterclockwise with a 6mm nut driver. 3. Insert ng o...

  • Page 31

    31 6mm wrench 1. Remove cooking grid from question mark side burner. Remover the two screws securing the question mark burner pipe, which are underneath the side burner shelf. Then take off the side burner pipe by hand. 2. Locate and remove the lp orifice at the end of each valve with a 6mm nut driv...

  • Page 32

    32 2. Use a 7 mm nut driver to remove the lp orifice located in the center of side burner tube. 3. Replace with a ng orifice to the valve then tighten it with a 6mm nut driver. And replace the side burner ring. Rear burner conversion tools required: phillips head screwdriver (+) 6 mm wrench monkey w...

  • Page 33

    33 2. Use a pair of pliers to steady the orifice holder and use a 6mm wrench to unscrew and remove the lp orifice. Replace with ng orifice. 3. After the orifice is replaced, put the cover of the rear burner back to its original location and the rear burner heat shield as well. Note: the 3 steps belo...

  • Page 34

    34 remove all packages before using this unit. Installation instructions ¾ before using your unit • remove the exterior and interior packing. • before connecting the unit to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the coo...

  • Page 35

    35 ¾ food storage • use plastic warp to keep food and place evenly on wire rack or drawer. • allow hot food to cool before put into this refrigerator. • allow space between different foods inside refrigerator. • keep food dry before storage. ¾ installing your unit • remove food from refrigerator if ...

  • Page 36

    36 y do not use this product in a manner other then its intended a purpose. It is not intended for commercial use. It is not intended to be installed or used in or on a recreational vehicle and/or boats. Y do not store this unit near gasoline or other combustible liquids or where other combustible v...

  • Page 37

    37 the bucket after the unit has cooled down completely. With a full load of fresh charcoal on the pan, raising the pan higher than the middle setting is not recommended. Charcoal lighting instructions y open grill lid. Y remove cooking grates using tool provided. Y adjust charcoal tray to the cente...

  • Page 38

    38 care and maintenance stainless steel there are many stainless steel cleaners available. Always use the mildest cleaning process first, scrubbing in the direction of the grain. Do not use steel wool as it will scratch the surface. To touch up noticeable scratches in the stainless steel, sand very ...

  • Page 39

    39 to clean the grill burners: 1. Clean the exterior of the burner with a wire brush. Use a metal scraper for stubborn stains or debris. 2. Clear clogged ports with a straightened paper clip. Never use a wooden toothpick as it may break off and clog the port. 3. Check and clean burners / venturi tub...

  • Page 40

    40 troubleshooting problems possible solutions grill will not light. 1. Push and turn the knob and check for sparks. 2. If there is a spark, check to make sure gas is supplied to the burner. A. Purge the line of any trapped air. B. Check to see if you can match-light the burner. C. Check to see that...

  • Page 41

    41 problems possible solutions burner blows out. 1. Check for any burner defects. 2. Check for proper burner installation. 3. Make certain the fuel mixture is not too lean. 4. Make sure the gas supply is sufficient. 5. See if the lp tank is empty. Low heat, lp gas. The propane regulator assembly inc...

  • Page 42

    42 limited warranty (model # 720-0677) nexgrill warrants to the original consumer-purchaser only that this product (model #720-0677) shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on th...

  • Page 43

    43 replacement parts list for replacement parts, call our customer service department at 1-877-323-5263, 8 a.M. – 6 p.M., pst, monday – friday and 8 a.M. – 12 p.M. Pst, saturday. Ref# description warranty coverage qty ref# description warranty coverage qty 01 temperature gauge 2 35 door magnet 2 02 ...

  • Page 44

    44 ref# description warranty coverage qty ref# description warranty coverage qty 69 drawer w/ panel, small 1 104 charcoal cook grid 1 70 drawer slide 4 105 grid lifter 1 71 bottom panel, (charcoal grill) 1 106 ventilation piece handle 1 72 right side panel, (charcoal grill) 1 107 ventilation piece 1...

  • Page 45

    45 figure 246 csa international project 2078110 46 of 46.